Cisco Wireless :: 5504 - Setup Back Controller From HA SKU Mode Into Standalone

Jun 17, 2013

I have two 5504 Controller. Original Liceses 100 per Controller. At the beginning the Controllers were running standalone as a Primary and secondary in a Mobility domain. Now they are running in a HA Pairing mode. One Controller as the Primary an the second as the Standby in the redundancy HA SKU mode. The first step SSO disable is done.
 
how setup back the HA SKU Standby-Controller to get again the 100 licenses?

View 4 Replies


ADVERTISEMENT

Cisco Wireless :: Aironet 2600 In Standalone Mode

Feb 18, 2013

I have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL

I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.

View 22 Replies View Related

Cisco Switching/Routing :: AIR-LAP1142n-a-k9 - Wireless AP Standalone Mode

Mar 18, 2012

I can run the Cisco AIR-LAP1142n-a-k9 access point in standalone mode? I don't want it to look for a controller when it boots up.

View 3 Replies View Related

Cisco Wireless :: 2500 Time Limitation For H-REAP Standalone Mode

Sep 4, 2012

We have a customer who is evaluating a Cisco Vs. Motorla wirless solution. He says that a Motorola AP can only work in standalone mode for 48 hrs. after it lost communication to the controller. Is there any limitation like this with a 2500 controller and 1140 series access points solution?. Is there any reference to show?

View 3 Replies View Related

Cisco Wireless :: AIR-LAP521-G-E-K9 Access Point Configuration In Standalone Mode

Aug 3, 2011

how to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.

View 4 Replies View Related

Cisco Wireless :: How To Setup A Standalone Aironet AP 1260 Series

Sep 13, 2011

I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?

View 3 Replies View Related

Cisco Wireless :: Aironet 1041N Standalone Access Points Setup Information

Jul 19, 2012

I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.

The reason why I'm writing is because I have a few questions to clarify.  
 
1) What is the best position for better signal, top side wall or corner ceiling?
 
2) How many client mac address filtering  can i do per access point?
 
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.

4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)

5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?

6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?

7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.

8) Can CCp software be used in these access points?

View 9 Replies View Related

Cisco Switching/Routing :: 3750x / Stackpower Switches Show In Standalone Mode?

May 29, 2013

I have a stack of 8 3750x switches connected via Stackwise.  In addition, I have these switches configured as two Powerstacks. When I look at the Powerstacks, they are showing as being in power-sharing mode.  When I look at the individual switches, they show as standalone.   Right now, I have 1 switch in each powerstack that has two power supplies, and then the other three have a single power supply. Below is the output for "Show stack-power detail" as well as the Powerstack configurations.
 
Power Stack           Stack   Stack    Total   Rsvd    Alloc   Unused  Num  NumName                  Mode    Topolgy  Pwr(W)  Pwr(W)  Pwr(W)  Pwr(W)  SW   PS--------------------  ------  -------  ------  ------  ------  ------  ---  ---Powerstack_1          SP-PS   Ring     2145    45      570     1530    3    3Powerstack_2          SP-PS   Ring     2860    60      760     2040    4    4Powerstack_1-1        SP-PS   Stndaln  1430    520     190     720     1    2
Power stack name: Powerstack_1    Stack mode: Power sharing    Stack topology: Ring    Switch 4:        Power budget: 700        Power allocated: 190        Low port priority value: 20        High port

[code].....

View 1 Replies View Related

Linksys Wireless Router :: Bridge Mode E2500 - Reset It Back To Normal

Nov 18, 2012

I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.

View 4 Replies View Related

Linksys Wireless Adapters :: Bridge Goes Into Sleep Mode / Loses Connection Back To EA6500

Feb 25, 2013

I use a WUMC710 bridge with desktop PC and a Printer connected to it. When those two devices have been inactive for a while the bridge goes into sleep mode and loses the connection Back to my EA6500. Trying to print something from wireless devices connected to the 6500 elsewhere in the network doesn't "wake up" the bridge. Ihave to unplug the power supply and restart it.

View 2 Replies View Related

Cisco Wireless :: 5508 Controller In HA Mode Support

Jun 6, 2011

is there a support of 1+1 mode (HA mode) at 5508 Controller? If yes Is there a HA bundle or do we have to order two identical 5508 controller ?

View 6 Replies View Related

Cisco Wireless :: 5508 - AP's In HREAP Mode Disassociate From Controller

May 22, 2013

I have been having an issue with random AP3602I's in HREAP mode disassociating from the 5508 controller.  These AP's are in remote offices with 70Mb WAN back to the controller.  Randomly one or two AP's disassociate from the controller and I have to bounce the switchport to bring them back online.  The WLC is running 7.2.  Again this only occurs to one or two AP's not all of the AP's. 

View 8 Replies View Related

Cisco Wireless :: 5508 After Rebooting Primary Controller Changed Into Maintenance Mode

Feb 10, 2013

custommer of mine tried to configure HA AP-SSO with two 5508 controllers. After rebooting the primary controller changed into Maintanence Mode. [code]

View 15 Replies View Related

H3 Wx5004 Setup H3c Wireless Controller

Feb 16, 2012

I have a h3 wx5004 wireless controller, I want to setup as such that the wirless clients could be Authenticated using domain credentials. I am using RADIUS and as far as my understanding , i have completed all the steps to make it work, but still it doesn't work.I have configured RADIUS Server on win 2008 R2 with proper settings with AD and certificates.

View 5 Replies View Related

Cisco Wireless :: How To Setup 5508 Series LAN Controller

Sep 23, 2010

how to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and  Management interface IP. The device IP is using what type service or management interface.

View 2 Replies View Related

Cisco Wireless :: WLC 2504 - Setup Guest Wi-Fi On Controller?

Jun 4, 2012

I have setup guest access on the controller and this is not working at the moment.
 
DHCP server setup on the controller for the Guest users.
 
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.

View 2 Replies View Related

Cisco Wireless :: WLC 2504 - Setup Guest Access On The Controller

Jun 4, 2012

I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.

View 10 Replies View Related

Cisco Wireless :: WAP200 Repeater Mode Setup?

Oct 19, 2010

I have 3 WAP200 wireless-G access points. I have one set up as an AP the other two are set up as repeaters to the main AP.
 
My question is Do I need a lan connection to each repeater ?
 
also, do I need to create SSIDs for all three? & if so, do they need to be the same?

View 7 Replies View Related

Cisco Wireless :: Setup 2504 WLAN Controller And 1142N Access Point?

Jun 13, 2013

We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?

View 1 Replies View Related

Cisco Switches :: SG300-10 / Setup Multiple Routed VLANs Going Back To FiOS Actiontec Router

Aug 13, 2011

I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode.  I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router.  My configuration is as follows.
 
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
 SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
 
I have a static route set on the fios router for both subnets setup as follows.
 
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
 
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1.  DNS set to the fios router (192.168.1.1). 
 
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan.  Traffic routes between vlans/and the default subnet on the fios without issue.
 
When I ping out, DNS resolves, but will not go past the fios router.  Am I missing a setting somewhere?

View 3 Replies View Related

Cisco Wireless :: SAP1602i - Setup For AP Running In Autonomous Mode For Clients?

Apr 25, 2013

I am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.

So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...

View 1 Replies View Related

Linksys Wireless Router :: E2500 - Way To Setup In Bridge Mode?

Sep 14, 2011

I just bought an E2500.  Wanted to set it up in bridge mode.  I can't seem to find any way of doing this.Cisco Knowledge Base article # 4194 shows what I am attempting to do.

View 1 Replies View Related

Linksys Wireless Router :: E1200 Management Mode And Faulty Setup

Aug 5, 2012

I can not even get in to management mode. In next program that just keeps trying to auto repair the connection and never displays any radio button option the direction state like "advanced settings".At the very least your PDF should match your user friendly **bleep** ware!The instructions even refer to itself wrong! It states "for manual set up go use browser connection section" then in that section it describes an auto set up and instructs you to follow the set up steps on the CD.

View 7 Replies View Related

Linksys Wireless Router :: WAG200G - Unable To Get 192.168.1.1 Setup Console In Bridge Mode Only

Jun 13, 2012

I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.

View 3 Replies View Related

RFS6000 Controller To Run Single AP650 Or It Can Be Set In Stand-alone Mode

Oct 28, 2012

Will i need another RFS6000 controller to run a single AP650 (isolated remote location) or it can be set in stand-alone mode ? I might consider install one antenna per location in 5 different store.

View 6 Replies View Related

Cisco Switching/Routing :: ATM 8510 Back To Back With 7206vxr 155Meg Only Get 44Meg?

Nov 25, 2012

I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-

kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled:  AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712   <====  

I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-

atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest  redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?

View 4 Replies View Related

Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card

Dec 4, 2011

What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?

View 1 Replies View Related

Cisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?

Apr 11, 2013

I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?

View 1 Replies View Related

Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?

Nov 25, 2011

I have 2650XM  router and 2620 Router Both routers have built in WIC  T1 CSU/DSU cards
 
2620Router --
 
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: DTE  side
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, loopback not set

[code]....
 
My question is that cisco website says there are two type of cable connections for this type of config --which are  --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable  it did not work.So for this type of connection i know i need T1 cross over cable--  which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over  --  will this cable work in my router to router connection.

View 5 Replies View Related

Cisco Switching/Routing :: 2611 / 2801 - Configuration For Back To Back Support

Oct 19, 2012

I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .

View 1 Replies View Related

Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?

Jan 8, 2013

I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire.  Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?

View 7 Replies View Related

Cisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection

Apr 14, 2013

I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?

View 2 Replies View Related

Cisco WAN :: E1 Clocking Back To Back 3925 Routers

Feb 29, 2012

Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved