I have a h3 wx5004 wireless controller, I want to setup as such that the wirless clients could be Authenticated using domain credentials. I am using RADIUS and as far as my understanding , i have completed all the steps to make it work, but still it doesn't work.I have configured RADIUS Server on win 2008 R2 with proper settings with AD and certificates.
View 5 Replieshow to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and Management interface IP. The device IP is using what type service or management interface.
View 2 Replies View RelatedI have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies View RelatedI have two 5504 Controller. Original Liceses 100 per Controller. At the beginning the Controllers were running standalone as a Primary and secondary in a Mobility domain. Now they are running in a HA Pairing mode. One Controller as the Primary an the second as the Standby in the redundancy HA SKU mode. The first step SSO disable is done.
how setup back the HA SKU Standby-Controller to get again the 100 licenses?
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies View RelatedI have only one PC. I use cross cable for setup Domain controller. Than network icon show available network but it is just only send and can't received.
View 1 Replies View RelatedI'm trying to verify some behaviors I'm seeing with my 5508 controller setup, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.
I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
I can connect to the controller via 10.10.8.200 both through the web interface and telnet
while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedWe have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedWe are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies View RelatedI am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
I've got my computer set up with a 2.4 Wireless USB Network Adapter. When I play online games I get a 'Connection Interutped' everything other 30 seconds or so.Now when I installed the Verizon stuff, the over the phone person told me to uninstall the SM Bus Controller. Now everytime I start up my computer I get a 'Found New Hardware' wizard telling me I should install the SM Bus Controller.
View 17 Replies View Relatedi have internet srevice working with my wireless usb stick or ethernet wire from my gateway modum. in device maneger i have network adapters listed and a question mark before network controller. windows auto update lists no driver avalible for it, and i would like to know it function/purpose?
View 1 Replies View RelatedI am having trouble adding a new controller(2500) to the WCS.
-My WCS version 6.0.196.0
-My WLC version 7.0.116.0
If i upgrade my WCS i may add the new contoller? Even if in cisco DATA-SHEET there isnt any mention regarding this WLC(basicly it says that the WCS does not support this WLC)
Monitoring and migration of selected Cisco Aironet standalone (autonomous) access points. Monitoring of the standalone access points of Cisco 800, 1800, 2800, and 3800 Series Integrated Services Routers.
How to get a WLC on a SRE up and running. I have a WLC installed and running on a 2951 SRE connected to a L3 switch in a lab.
I've tried to follow the Cisco document:
[URL]...
My wireless clients could only receive a DHCP allocated IP address for the 55.XX subnets defined on the wireless lan controller and SRE (shown on page 12 of the pdf). All traffic seemed to be routed via the native vlan of the inside router trunk interface and all DHCP requests arriving at my DHCP server were from 55.XX. Because of this I didn't see the point of trunking
so I've changed it to a point to point routed connection, created a 55.XX DHCP scope on my DHCP server for the wireless clients and all routing works fine.I found the document rather misleading.
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
Due to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedInterface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies View RelatedI have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?
View 2 Replies View RelatedWe have two 4400 WLC's. We have around 20 access points in our network.If we assign controller1 as primary for half of the access points and controller 2 as primary for the other half, does this mean the association of the ap's indicate load balancing by the controllers. Does this mean wlc does load balancing as different ap's associate on different controllers. or does it only server as active-standby wlc.
View 2 Replies View RelatedI've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View Relatedhow I can find out what version of SSH that a cisco 2106 wireless LAN controller is using?Is there a CLI I can type to figure that out or do they only support one version?
View 1 Replies View RelatedWell I was trying to get my D-Link DIR-615 router too run DDWRT so I could use it as a wireless reciever.But things have gone wrong, the wireless controller no longer works. and I'm trying to restore the original factory firmware.(this is a spare router we had sitting around it's not an important asset) it boots up fine with DDWRT firmware the wire functions still work, but I needed the wireless functions.I just can't get the original firmware back.
View 1 Replies View RelatedI currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View RelatedCan 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies View RelatedMy customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies View Relatedi converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
By any way can I achieve HA in 2500 controller? I dont mind even I didnt get Stateful switchover.
View 5 Replies View Related