Linksys Wireless Router :: E1200 Management Mode And Faulty Setup
Aug 5, 2012
I can not even get in to management mode. In next program that just keeps trying to auto repair the connection and never displays any radio button option the direction state like "advanced settings".At the very least your PDF should match your user friendly **bleep** ware!The instructions even refer to itself wrong! It states "for manual set up go use browser connection section" then in that section it describes an auto set up and instructs you to follow the set up steps on the CD.
View 7 Replies
ADVERTISEMENT
Aug 25, 2012
I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it.
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar.
View 1 Replies
View Related
Dec 3, 2012
I installed an E1200 router today. It automatically upgraded the firmware to the latest when I did this. Everything went smoothly.
I connected my desktop wired and my laptop wireless. I ran three different speed tests: Xfinity, speedtest, and cnet. All three showed 25-35 Mbps download and 4-5 Mbps upload. That is what my old router had too. So far, so good.
I ran the speed test that came with the E1200 router. It showed 0.30- 0.66 Mbps download and 0.58 - 2.09 Mbps upload. Note the decimal points!
Bottom line: The E1200 seems to be working fine, except that its internal speed test seems to be broken, at least when testing from a wired machine.
View 2 Replies
View Related
Oct 12, 2011
Well I accidentally put the router in bridge mode. It's a e1200 or 2500 I'm not exactly sure. But I was wondering how I can get it out? I can't access the web interface at 192.168.1.1 however I can access my modem's interface at 192.168.254.254.
View 4 Replies
View Related
Oct 17, 2011
I've DMZ'd my computer using the the E1200's Web Browser Config screen (192.168.1.1) yet when I try to test the ports not a single one is open.
I've used this test to see if they were open: [URL]
And almost none of them were. Is there any issue that could be causing this?
Also when I try to open a single port the site says it times out. Opening single ports didn't work either. I've also tried to DMZ via the IP and the MAC address of my PC and still no luck.
View 9 Replies
View Related
Mar 18, 2013
I have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies
View Related
Jan 19, 2012
I have been attempting to set up a linksys wireless-n e1200 router on my hp p6-2007c (Windows 7 SP1, 64-bit) desktop pc for the last day and have exhausted everything i can think of. The previous router was a linksys WRT54G and it worked fine. However, upon setting up this new router i get a "no internet access" message accompanied by the little yellow triangle and the ability to still connect to my router via its ip address to alter its configuration. The connection status for the network and the internet is identical for all the laptops in my house. I originally attempted setting up the router using Cisco's setup program. At its conclusion, the setup program informs me that i am connected to the router, but my internet connection has been lost (even though it was never there) I have tried starting over from scratch by resetting the router back to its default settings and using a variety of different channels (Auto, 1, 6, and 11), frequencies, etc. I have uninstalled norton antivirus, disarmed the windows security programs, made sure of TCP/IP settings, rolled back, uninstalled, and finally updated firmware, uninstalled/reinstalled driver for wireless card, disabled/enabled the card itself, deleted all other previous network profiles still present in the "Manage Wireless Networks" screen, and probably some other suggestions i came across in this forum. They all failed with the same results, i.e. the ability to connect to the network locally and having no internet access.
View 1 Replies
View Related
Jan 3, 2013
I wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies
View Related
Sep 19, 2012
My macbook is able to detect my router, but the router cannot connect to the internet. I was wondering if the E1200 requires a modem, where as FIOS only offers ONT?
View 1 Replies
View Related
Jan 20, 2013
I have E1200 router and I have a problem with setup my ISP Connection. The ISP requires PPPOE connection but with static IP Address but in E1200 I didn't find any option for that. The possible ways are PPPOE or Static IP Address.
View 1 Replies
View Related
Apr 4, 2012
Im running a pre intel mac g5 with 10.5.8 on it and when i insert my setup disc for my new e1200 router there is a slash through the start up icon and then i get a message that its not supported by my architechure. Is my computer to old to set up this router???
View 2 Replies
View Related
Nov 29, 2012
I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
View 6 Replies
View Related
Sep 12, 2011
The browser-based settings utility for my E1200 can't setup MAC address filtering. I go to the "Wireless MAC Filter" page and enable MAC filtering.When I click the “wireless client list” button, a new window opens saying “IE cannot display the webpage”. This always happens when I have a wireless connection active.When there are no active connections, then IE properly displays the MAC address table, but it is empty since there aren't any computers connected to the router.
View 5 Replies
View Related
Aug 23, 2011
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
View 7 Replies
View Related
Sep 19, 2012
I'm having the same problem. How do I switch the wireless mode? Google searches have been of no use.
View 1 Replies
View Related
Jul 22, 2011
I try to connect my IPod touch to the wireless router E4200 Firmware 1.0.02 build 13 and I got this error Unable to join the network “n2”.This is my 2.4 GHz Wireless Settings:
Network Mode: Wireless-N only
Network Name (SSID): n2
Channel Width: Auto
Channel: 9 – 2.452GHZ
Security Mode: WPA2
I spoke with customer service and I went through all the setting change possible without success, she told me maybe the problem was with my iPod and I have to call apple customer service. I can connect the iPod to my old wireless router successfully with not issues, using 2.4 GHZ only N Wireless Settings.The another issue I is when I use 2.4 GHz N is not connecting with a good speed (Max speed 64 Mbps) I know my pc have a max of 300 Mbps and again when I connected using old wireless I get max speed. I analyze all spectrum around the router is located; I change the channel to the one that are not in use for another router. Same speed, no improve of performance.
I found in the report from the Wi-Fi spectrum analyzer said band N 5 GHz max rate 450 Mbps that is the speed that is supposed to be, but for 2.4 GHz N max rate 144 Mbps, so there is a problem with the router that is no giving the right speed and standard specification for band 2.4 GHz N. I did same test with older firmware release and same issue. I tried all setting possible and I get same outcome, no iPod connection and low speed rate with a max of 144 Mbps (It’s supposed to be 300 Mbps)
View 9 Replies
View Related
Sep 14, 2011
I just bought an E2500. Wanted to set it up in bridge mode. I can't seem to find any way of doing this.Cisco Knowledge Base article # 4194 shows what I am attempting to do.
View 1 Replies
View Related
Jun 13, 2012
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies
View Related
Jan 20, 2007
How to setup WRT54G in router mode
View 9 Replies
View Related
Dec 22, 2012
I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies
View Related
Jun 5, 2012
I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies
View Related
Aug 12, 2012
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies
View Related
May 1, 2013
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies
View Related
Nov 7, 2011
I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies
View Related
Jan 4, 2012
Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies
View Related
Oct 23, 2012
Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.
View 1 Replies
View Related
Dec 29, 2011
I can't see where to set a user name on my E1200. I set a password for the web interface then it boots me out and I am promted for the password and username.I don't want to download and configure my router with some poorly written software for my mac; why can't I just do it all through the good old web interface???? I'm able to set everything else up fine but when i set the password I am basically rendering the web interface usless and have to reset the router!! (running Lion, latest build with 8gigs of ram and N wirless adaptor in lappy)
Ok, so I was given this router for free so I shouldn't complain but I do not see any speed increase over my 6 year old 54G rinning wrt, perhaps I need summin better than this $50 walmart special Getting about 10mps download which is also the theoretical max of G right)
View 6 Replies
View Related
Jun 9, 2012
I set my router to allow my xbox360's mac address, not knowing that it would kick out all of my other devices. So now I can't access my own router and I need to reset it. How do I do that?E1200 series linksys router. I'm looking for an ethernet cable and my installation disk right now to see if I can connect with the cable and maybe use something on the disk if I have to.
View 1 Replies
View Related
Dec 26, 2012
I replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies
View Related
Apr 16, 2013
my wifi router is E1200 at first it works very fine but then when the time you unplugged it and turn it on again it won't work already i mean its working the lights are on and blinking but there's no wifi... why does it happen??? i don't understand...i have already did the 30-30-30 rule the hard reset thin but still nothing's change...
View 5 Replies
View Related
Dec 29, 2012
i'm having connection issues requiring frequent reboots of my router. it starts with internet slowdown to a crawl, then it times out and lastly the webinterface is not even responding when i try to access it to reboot. Requiring me to manually unplug. this happens once a day atleast.
Sometimes it recovers after a few minutes and get on the net.i've tried flashing, reflashing, re-reflashing , resetting , re-resetting, to no end. And all the usual tricks tech support ask to do.
i didn't use to have this problem before the firmware update
08/31/2012
Ver.2.0.04 (Build 1)
i would just like to flash to the previousl version and test if this still happens.
View 9 Replies
View Related
Jan 17, 2013
I have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies
View Related
Sep 21, 2012
I can connect to the guest account but it cannot resolve DNS addresses; how should the router be set up?
The regular (non-guest) account works as advertised. The E1200 is connected to my Verizon modem/router. I have tried disable/enable of DHCP on the E1200; I have tried setting the E1200 Static DNS 1 to my Verizon router IP address without success.
View 6 Replies
View Related
