I have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
I tried seeing if it would pull a DHCP address on my network but it didnt.
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies View RelatedI have a PC running my server application and several iPad Clients, and therefore need a WLAN to connect them.
Can I simply plug an access point such as a Cisco Aironet 1602i into the LAN port of the PC to accomplish this?
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies View RelatedI have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL
I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.
For some time now I have been looking for a good business class wireless AP. I've narrowed it down to the Cisco Aironet 1140 standalone (no controller). I'm no stranger to Cisco products. I've worked with their routers, switches and Pix/ASA firewalls. However, I've not had the opportunity to work with their wireless AP's. Anyone using these AP's (more specifically the 1140 standalone), can provide information on the reliability and security of these devices. Some of the features I would like to have like Radio Mgmt. and Rogue AP Detection I see are only available on the controller based units. Does not having these features on the standalone unit reduce its reliability and security? This is for a small business and the budget does not allow to drop for a controller at this time.
View 7 Replies View RelatedI'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedI just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
I am using an Aironet 1142 standalone AP and want to use Apples Bonjour Service between iOS devices e.g. iPad and Apple TV.I have found here some posts that suggest to disable igmp snopping but this didn't worked for me.All devices are in the same vlan/subnet. Do I need to configure something special?
View 3 Replies View RelatedI recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
We have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
how to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.
View 4 Replies View Relatedhow to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies View RelatedWe are planning a wireless network using the 1602i APs. Some of our APs might or might not be within the 100m limit from the switches, so we'll be running them as repeaters instead. Right now, we are planning on buying power injectors for everything, but I can't seem to find an answer to this question:
If I'm running an AP as a repeater (no ethernet running back to a switch), can it still receive power from a power injector and a short ethernet run between the injector and the AP? Or will I need to use a power adapter?
i have currently a 2504 WLC and some 1602i AP's.Basically so far i have configured the WLC as per the guidelines on the startup and now i want to join the AP's (which i haven't managed to do yet) and the setup the wireless network.I can get the AP to join and pickup an ip address and that is it. It comes up with different error messages from the WLC, and through hyper terminal, none of which i understand but the main jist is the following:
*spamApTask4: Feb 19 15:05:56.171: #CAPWAP-3-DECODE_ERR: capwap_ac_sm.c:3844 Error decoding Join request from AP 6c:20:56:0e:23:e0
AND
0Tue Feb 19 15:06:19 2013AP with MAC 6c:20:56:0e:23:e0 (AIR-CAP1602I-E-K9 ) is unknown.
AND
We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies View RelatedNeed simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies View RelatedI have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies View RelatedI have an Aironet 1142 access point.
Is it possible to direct it to a webfilter hardware firewall for internet access. For example the IP of the firewall with webfiltering capabilties would be 192.168.0.1
We are hoping to provide customer wifi web access but need to filter what they can access.
I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies View RelatedI bought a Cisco Wireless AIR-CAP2602i-E-K9 and have some practice on Cisco routers, but can not log in "Global Configuration Mode", not existe the command "Configure". How active configuration?
View 10 Replies View RelatedHow can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies View RelatedWe have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies View RelatedOkay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.
View 14 Replies View Relatedhow I can configure the Aironet 3600e by Cisco without a WAN Controller. I know it's a controller based AP but I bought it in preparation for my new WiFi Network Design as I'm planning to deploy these APs together with a controller but at this stage all I need is just basic config so that I can see how good it will work in the environment I want to implement it. So I was wondering if there is some kind of default IP and Admin/ Password as I could not find the info on Cisco's website.
View 4 Replies View RelatedWith this customer they have 4 floors with on each floor a Cisco Aironet 1130AG. At the moment they are using WEP as a protection with a really long key. The users find this annoying, but I am more concerned about the security perspective. So I want to implement WPA2 with a shorter key for the people to remember. On one floor, I also want to add a public network when other people want to connect and just need internet access. How to change the current set-up and regarding the security and implementation. If all of the Access Points could work togheter and just be 1 wireless network. I don't know if this is possible and how to do it? For the public network I know there also need to be some changes in VLAN's. The firewall is a cisco ASA5505.
At the moment I am running this configuration: I tried setting up this with the GUI, but it doesn't look like the configuration at the moment is shown in the GUI or maybe I am just looking in the wrong places. [code]
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
I can't figure out how to get the config right for the 802.11n channel to work.
View 4 Replies View RelatedI'm looking at creating WLANs using standalone APs for the first time. I know this can all be done with trivially a controller, but this project can't stretch to that...Can I use MAC filtering on standalone APs to restrict which clients associate?I think these will be 1240AG devices but I assume the answer is the same for all models?Can I mix MAC filtering with WEP/WPA? And use MAC filtering without encryption?
View 2 Replies View RelatedI have a Brand new AP that was bought for a site which has a controller, however it was never installed. I was wondering can you downgrade this AP to make it work in stand alone mode as a normal AP?
View 1 Replies View RelatedOne of Cisco Wireless AP 1242 installed in my premises restarts itself; AP is getting power from Catalyst 2960 POE. I am using multiple SSID on this AP. I have issued the show tech-support. I have seen below in tech-support System was restarted by unknown reload cause - reason ptr 0xF, PC 0x46FEB8, address 0x0? what could be the reason of restarting of AP. AP is in production since 1 year and it restarts seldom.
View 2 Replies View Related