Cisco Wireless :: AP 1041 - Copy Aironet IOS Configuration?
Dec 6, 2012
I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies
ADVERTISEMENT
Nov 16, 2012
I have a Cisco Aironet 1041 , what a good repeater/wireless extender that works with it to cover an area of 50 squared meters ?
View 4 Replies
View Related
Oct 30, 2012
I have 2 SSIDs mapped to 2 VLANs (other VLANs are configured, but not used) Security is set to WPA2
What do I need to change to get higher connection speed? What is the highest for this model? Why won't it let me select 40Mhz channel width? Telnet says on 20Mhz available (GUI says it is in "Least congested" mode even though it is not)
View 5 Replies
View Related
Oct 5, 2011
I have done a wireless site survey at a library and one AP541N will cover everything pretty well. They do have one spot where the radio strenth is not quite as strong, but you would never buy a second access point for just that one area. I did the SIte Survey using a 541N Access point.
Here is my question. I see that the Aironet 1041 is very similar in price and according to the documentation has a stronger power rating and higher antenna gain. Why would I not buy an Aironet 1041?
We are just mounting to a wall and are planning on using the pwrin4 to provide POE for whichever we buy.
View 1 Replies
View Related
Sep 11, 2012
I am trying to setup a Cisco Aironet 1041 on my network for WiFi authinentication and access and I do not have a Radius server and was wondering if it is possible to configure the 1041 to authenticate with just WPA or WPA2 and a PSK without any of the other configurations? This setup is only going to be temporary untill I can get the appropriate infrastructure in place to facilitate the Radius server setup I really want in 12 to 18 months from now.
View 9 Replies
View Related
Jul 7, 2011
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies
View Related
Feb 22, 2011
When I try to import configuration from the controller 4400 to my WCS it gives the following message:
Status Refresh succeeded but some records were dropped because their key fields failed validations.
When i see the config in the WCS, all of my light access points are not on it. I check for the logs and this is What I get: (its a lot of info, so I am putting an example!)
02/23/11 14:18:46.784 ERROR [general] [TP-Processor7] THROWcom.cisco.server.common.errors.InternalException: [COMMON-1]: COMMON-1com.cisco.server.common.errors.ObjectNotFoundException: COMMON-
[code]......
View 3 Replies
View Related
Mar 21, 2012
We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies
View Related
Oct 11, 2012
I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
View 3 Replies
View Related
Sep 1, 2012
I don't know how to copy / paste the ip config so I ss'd it:(url) internet provider is RCN, I have AVG and Malwarebytes installed, I've tried disabling them both and didn't fix it! Anyways my internet was working fine, until one day it just suddenly stopped working. We have multiple computers hooked up to the network (5) and all work except mine. This same problem happened to my sister's computer, she has almost the same model as mine. We fixed it by switching it to wireless, but I was wondering if there was any way around that. It's a HP Pavilion. The box thingie lights up green and everything. I can access the other computers through the network, it's just the internet that won't work.
View 3 Replies
View Related
Dec 16, 2012
We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies
View Related
Oct 8, 2012
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies
View Related
Jun 6, 2013
I have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies
View Related
Jul 17, 2012
I have an Aironet 1142 access point.
Is it possible to direct it to a webfilter hardware firewall for internet access. For example the IP of the firewall with webfiltering capabilties would be 192.168.0.1
We are hoping to provide customer wifi web access but need to filter what they can access.
View 2 Replies
View Related
Jun 11, 2013
I have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
I tried seeing if it would pull a DHCP address on my network but it didnt.
View 1 Replies
View Related
Jan 10, 2012
I am using multiple cisco 2811, 3745 routers and 2950,3550 switches if I need to copy running configuration I have to go to each device and say copy run tftp: <address> Is here any way that automatically by schedule one a week or a month configuration copy from all devices to tftp server?
View 2 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
May 29, 2013
I bought a Cisco Wireless AIR-CAP2602i-E-K9 and have some practice on Cisco routers, but can not log in "Global Configuration Mode", not existe the command "Configure". How active configuration?
View 10 Replies
View Related
Mar 17, 2012
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies
View Related
Feb 1, 2012
We have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies
View Related
Mar 19, 2013
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies
View Related
May 21, 2013
I have two access points that I recently purchased from ebay. I updated them both to c1140-k9w7-mx.152-2.JB and I have been unsuccessful at getting either of them to connect at faster than 39MBps. After scouring google for answers I found several with the issue of not using the correct WPA2/AES configuration and that was me. However after changing the configuration, I am still unable to connect to either of the APs at faster than the 39Mbps. [code]
View 4 Replies
View Related
Sep 18, 2012
There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
View 3 Replies
View Related
Apr 3, 2012
I have a wireless network using the cisco ap 1041 converted into the anonymous. however it seems like every morning or evening I have to attached it back to the SSID all over again. it will not give me an ip address. I also would have to put the encryption key in again. I am using WEP 40 bit.
View 4 Replies
View Related
Apr 20, 2012
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Mar 7, 2013
Okay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.
View 14 Replies
View Related
Jul 25, 2012
how I can configure the Aironet 3600e by Cisco without a WAN Controller. I know it's a controller based AP but I bought it in preparation for my new WiFi Network Design as I'm planning to deploy these APs together with a controller but at this stage all I need is just basic config so that I can see how good it will work in the environment I want to implement it. So I was wondering if there is some kind of default IP and Admin/ Password as I could not find the info on Cisco's website.
View 4 Replies
View Related
May 3, 2012
We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies
View Related
Jul 4, 2012
With this customer they have 4 floors with on each floor a Cisco Aironet 1130AG. At the moment they are using WEP as a protection with a really long key. The users find this annoying, but I am more concerned about the security perspective. So I want to implement WPA2 with a shorter key for the people to remember. On one floor, I also want to add a public network when other people want to connect and just need internet access. How to change the current set-up and regarding the security and implementation. If all of the Access Points could work togheter and just be 1 wireless network. I don't know if this is possible and how to do it? For the public network I know there also need to be some changes in VLAN's. The firewall is a cisco ASA5505.
At the moment I am running this configuration: I tried setting up this with the GUI, but it doesn't look like the configuration at the moment is shown in the GUI or maybe I am just looking in the wrong places. [code]
View 1 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
View 2 Replies
View Related
Jun 25, 2012
I can't figure out how to get the config right for the 802.11n channel to work.
View 4 Replies
View Related
