Repeater / Wireless Extender For Cisco Aironet 1041?
Nov 16, 2012I have a Cisco Aironet 1041 , what a good repeater/wireless extender that works with it to cover an area of 50 squared meters ?
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: 1041 Aironet AP Not Reaching N Speeds
Oct 30, 2012I have 2 SSIDs mapped to 2 VLANs (other VLANs are configured, but not used) Security is set to WPA2
What do I need to change to get higher connection speed? What is the highest for this model? Why won't it let me select 40Mhz channel width? Telnet says on 20Mhz available (GUI says it is in "Least congested" mode even though it is not)
Cisco Wireless :: AP 1041 - Copy Aironet IOS Configuration?
Dec 6, 2012I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies View RelatedCisco Wireless :: Range Of AP541N Versus Aironet 1041
Oct 5, 2011I have done a wireless site survey at a library and one AP541N will cover everything pretty well. They do have one spot where the radio strenth is not quite as strong, but you would never buy a second access point for just that one area. I did the SIte Survey using a 541N Access point.
Here is my question. I see that the Aironet 1041 is very similar in price and according to the documentation has a stronger power rating and higher antenna gain. Why would I not buy an Aironet 1041?
We are just mounting to a wall and are planning on using the pwrin4 to provide POE for whichever we buy.
Cisco :: How To Setup Autonomous WPA Access On Aironet 1041 AP
Sep 11, 2012I am trying to setup a Cisco Aironet 1041 on my network for WiFi authinentication and access and I do not have a Radius server and was wondering if it is possible to configure the 1041 to authenticate with just WPA or WPA2 and a PSK without any of the other configurations? This setup is only going to be temporary untill I can get the appropriate infrastructure in place to facilitate the Radius server setup I really want in 12 to 18 months from now.
View 9 Replies View RelatedWireless Repeater And Extender Same Thing?
Jan 21, 2013I struggle getting a wireless internet signal in some parts of my house downstairs and all upstairs. Is a wireless router or repeater the same thing and which do I need.
View 3 Replies View RelatedLinksys Cable / DSL :: WAG200G As Wireless Extender / Repeater
Jun 19, 2012I got myself a HW500G as my main Wireless router. But as I moved to a new home with a very large space, I did start to have alot of dead spots which made me think about getting my old WAG200G out of the box and use it as Wireless extender.Is that possible with WAG200G and If yes, can you provide me with guidelines on how to do so.
View 2 Replies View RelatedD-Link DIR-655 :: Wireless Range Extender Or Repeater / Booster
Nov 20, 2011I am moving my office from one side of the house to the other which has real spotty wireless coverage. Most likely I will not be able to move the modem or wireless router, so I have to somehow increase the range.I did some research and poking around on forums, but I can't find a clear cut, number 1. What you think would be the best option to pair with the DIR-655.
View 1 Replies View RelatedWLR 4000 - How To Use A Linksys Wireless G Access Point As A Repeater / Extender
Aug 10, 2011I have a Sitecom WLR 4000 wireless router. I also have a Linksys Wireless G Accespoint. Can I use that AP as a extender/repeater for the Sitecom router? If yes, how to configure one and other?
View 4 Replies View RelatedLinksys Wireless Router :: Using DIR-600 As Repeater Or WLAN Range Extender?
Oct 11, 2012Can I use the WIRELESS 150 ROUTER DIR-600 as repeater or WLAN range extender?
View 1 Replies View RelatedTp-link 150mbps Wireless :: Wr700n Difference Between Wifi Range Extender And Repeater
Apr 9, 2013Region : Singapore
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
Since i know there's a "Repeater Operation Mode" in TL-WR700N Wireless Lan Mini Pocket Router, so what's the difference between TL-WA850RE WiFi Range Extender?I know the maxium speed support is different, but.... what else ?
Cisco Wireless :: Setting Up Aironet 1142n As Repeater?
Aug 9, 2012I've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
Cisco Wireless :: Can The Aironet 1310 Setup As A Repeater
Jul 10, 2012Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies View RelatedCisco Wireless :: Set Aironet 1232AG-A-K9 As Repeater While Using 4402 Controller
Oct 8, 2012Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.
View 2 Replies View RelatedCascading Routers - Using As Extender / Repeater With 2nd Router?
Dec 2, 2011Do I have to hard wire both routers to use cascading routers technique? I've been reading up on how to do this, but have not yet quite tried. I know someone will say extender and/or repeater, but I want to know if I can use a second router to extend the wireless signal further; i.e., bounce it from modem/gateway/wireless router (dlink) to wireless router (linksys wrt160n) then to my laptop? I have to go from one building to another and currently the wireless signal is quite weak (hence, someone will likely say repeater/extender). I already have the linksys. The dlink belongs to someone else, but I have permission to access through their dlink. I can do the initial setup, connecting LAN (main router - dlink) to WAN (2nd router - linksys), but I cannot leave them connected.
View 9 Replies View RelatedAsus RT-N66U / Range Extender Or Repeater?
Feb 3, 2013going to be setting up my cable modem and Asus RT-N66U router in my basement in the work room/laundry room. My townhouse is 3 stories tall so just in case I wanted to look at my options for a range extender or repeater.
View 1 Replies View RelatedNetgear WN2000RPT / Wi-Fi Range Extender / Repeater Recommendations
Jul 17, 2011I recently bought a Netgear WN2000RPT from Best Buy and I couldn't manage to get past the setup (wouldn't connect with my existing router), and I'm returning it tomorrow.
I just need to repeat the wireless-G signal downstairs to the other side of the house upstairs.What are your recommendations?
Cisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point
Feb 12, 2013In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
Cabling / Cards :: Using Second Belkin F7d1301 Router As Repeater Or Range Extender?
Apr 7, 2011i have beetel adsl2+router connected to my main computer through ethernet cable but its wifi signal is very low. its signal hardly reach the other end of my house where my bedroom is, and i want to surf on my laptop or mobile from my bedroom only so basically i want to extend my wifi range or boost the signal the thing is i have a belkin f7d1301 basic n150 wireless router, i want to know whether i can use it as range extender or any other thing to boost my signal.
View 7 Replies View RelatedCisco Wireless :: 1041 Or 1141 Won't Go Faster Than 39Mbps
May 21, 2013I have two access points that I recently purchased from ebay. I updated them both to c1140-k9w7-mx.152-2.JB and I have been unsuccessful at getting either of them to connect at faster than 39MBps. After scouring google for answers I found several with the issue of not using the correct WPA2/AES configuration and that was me. However after changing the configuration, I am still unable to connect to either of the APs at faster than the 39Mbps. [code]
View 4 Replies View RelatedCisco Wireless :: Captive Portal On AP 1041 / 1042
Sep 18, 2012There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
Cisco Wireless :: 1041 Access Point Converted Into Anonymous?
Apr 3, 2012I have a wireless network using the cisco ap 1041 converted into the anonymous. however it seems like every morning or evening I have to attached it back to the SSID all over again. it will not give me an ip address. I also would have to put the encryption key in again. I am using WEP 40 bit.
View 4 Replies View RelatedCisco Wireless :: Convert 1041 In Autonomous AP Mode To Lightweight?
Apr 20, 2012Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedCisco Wireless :: 1041 / 1042 - Apple Ipad Intermittent Wi-Fi Connectivity?
May 3, 2012We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedCisco Wireless :: AP 1041 Conversion From Autonomous Mode To Lightweight Mode
Mar 4, 2012We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies View RelatedCisco :: WLC 2500 And AP 1041 - To Use HTTP For Web Authentication
Jun 4, 2013We are using WLC 2500 and AP 1041 with web authentication. Due to we do not have the trusted/public certificate and want to get rid of the certificate warning during the user login. Is this possible to change the web authentication method from HTTPS to HTTP.
View 1 Replies View RelatedCisco :: Configure WPA2 On 1041 Access Point?
Dec 27, 2011configure WPA2 on a 1041 access point? I am trying to get it configured through the GUI and part way through I keep getting locked out of the AP due to WPA2 being partially configured..
View 1 Replies View RelatedWireless Extender Not Working
Jun 6, 2012I have exactly the same problem as tywanda46. I can't ping to 192.168.2.2 and i can't connect to http://extenderXXXXXX. I used de 6 characters from my access key.I can't attach the printscreen that i have made from the IPconfig /all in a DOSbox. The TSG editor asks for an URL with an image.
View 3 Replies View RelatedWireless Extender Will Not Work On PCs?
Sep 25, 2012I recently purchased a wireless extender to use on my PC, PS3, and kindle since I have such a low signal in my bedroom. I connected the extender to the PS3 and kindle with no problems. Great signal. Increased from 1 bar to 3 bars. However I can't connect either one of my PCs to it. It connects but says no internet access.
View 9 Replies View RelatedCisco Wireless :: Proper WDS Extender For RV180W
Oct 6, 2012I recently replaced my working WRVS4400N v2 Router with an RV180W. Unfortunately I am now stymied, as I am unable to use WDS to connect my WAP4410N to the RV180W to fill a dead spot. I tried calling support (case # 623405011) but we were unable to get communications working correctly - even when the two devices were less than 5 feet apart. The engineer's final suggestion wwas to put the WAP4410N bact to factory default, connect it to a laptop, and compare settings side-by-side...thats 2 hours of my life I will never get back as it was a useless endeavor. The WAP4410N is on 2.0.5.3, and the RV180W is on 1.0.1.9 (Both are on the latest available firmware).
My question would be what Cisco device would be best matched with this RV180W so I can use WDS and fill in the hole. I have no problem, just as long as it works and stays stable, as I had with the WRVS4400N / WAP4410N setup. Optionally, is there some other setting the engineer missed? The RV180W is my gateway router and primary wireless access point, I just need to fill some spaces where there is interference.
Extending A Wireless Network From An Extender
Dec 28, 2012Is it possible to extend a wireless network from an existing extender?I have a BT Home Hub extended to a Netgear Extender.I have tried to extend this on from the netgear with an Edimax without success.Is there anything from www.ebuyer.com that I could try.
View 2 Replies View RelatedCannot Connect To Netcomm Wireless N Extender?
Jul 9, 2012I recently just bought a Netcomm NP124 wireless extender as a computer on the other side of my house does not get within the range of my routers wireless.So i have opened the package and followed the step by step manual of how to set it up. it is as follows:
1. to initially set up the product we recommend you plug the NP124 into a power socket near both you existing router and computer (DONE successfully)
2. Plug the supplied Ethernet cable into your NP124 and connect the other end to the computer (DONE successfully)
*this is where the problem lies*
3. you can connect your devises through the web user interface. to open the web browser (internet explorer, Firefox, etc) and type 192.168.20.1 into the address bar and hit enter.
4. When prompted add in the username and password.
Before i keep going i must tell you that my desktop computer doesnt have wireless but my modem/router does so i connect my computer to my router via an ethernet cable.There are further steps but i cannot get past step 3. When i attempt to type the IP in the URL it says "problem loading page", "unable to connect". At all times my phone line is connected to my modem/router. These are the cable variations i have tried:
a) -ethernet from computer to NP124
-No ethernet connection from modem/router to computer
**this is the procedure outlines in the manual, does the manual assume i have a wireless connection
to the internet in my desktop?**
b) -ethernet from the computer to the modem/router
-ethernet from the NP 124 to the moder/router
c) now using an Ethernet hub:
-(ALL) NP124, modem/router and desktop connected to the hub at the same time
I cannot see why the IP does not connect, without this stage i cannot enter the wireless settings of the NP124. I have tested to see if other IP addresses work in the URL (eg the modems 192.168.1.1) and it works but the NP124 doesnt.
Wireless Extender Not Keeping A Connection?
Oct 17, 2012I have a wireless repeater (NETGEAR Universal Wifi Range Extender WN2000RPT) thats been giving me issues lately when attempting to use it to connect an xbox 360 I have to xbox live. The Xbox and the repeater are connected by an ethernet cable so there is no wireless connection going on between them. My router (Cisco WRVS4400N Wireless-N Gigabit Security Router with VPN) located in the basement of my house, and the extender is on the second floor of my house. The xbox that I want to connect to the internet is located on this second floor and because of the distance between it and my router a normal xbox wireless networking adapter doesn't seem to be working.Anyway, if I plug in the extender and let it get a connection, and use it right away to connect, i have no issues. The connection will also usually remain working for a while after I first get it working. The problem comes after I'm done using the xbox and i shut off the console and the tv. When I come back to the xbox later and turn it on, the networking extender still shows it has a full connection and is working properly on the outside with the green lights, but the xbox will not connect and it will tell me the extender is not assigning an IP automatically (DHCP turned off), when I know for a fact it is turned on. It is almost like the extender freezes after I leave it alone and on for a while. When this happens I usually unplug it and let it connect, and everything works as it should again. After a while its gotten a little annoying having to do this every time I need connection.
View 5 Replies View Related