I have a wireless network using the cisco ap 1041 converted into the anonymous. however it seems like every morning or evening I have to attached it back to the SSID all over again. it will not give me an ip address. I also would have to put the encryption key in again. I am using WEP 40 bit.
View 4 Repliesconfigure WPA2 on a 1041 access point? I am trying to get it configured through the GUI and part way through I keep getting locked out of the AP due to WPA2 being partially configured..
View 1 Replies View RelatedIs there any possibility to set linksys E4200 for support anonymous acces to ftp server in read and write mode ?
View 1 Replies View RelatedI am trying to setup a Cisco Aironet 1041 on my network for WiFi authinentication and access and I do not have a Radius server and was wondering if it is possible to configure the 1041 to authenticate with just WPA or WPA2 and a PSK without any of the other configurations? This setup is only going to be temporary untill I can get the appropriate infrastructure in place to facilitate the Radius server setup I really want in 12 to 18 months from now.
View 9 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
I have successfully converted my lap1242ag-c-k9 to autonomous mode. But when i try to set ssid or wep then hit apply it won't the changes i made.
View 3 Replies View RelatedI am using a linksys wrt600N with easylink advisor version 1.6.0042. I am trying to install a video camera and the instruction manual says under "known issues": LinkSys routers have a factory default setting in the firewall menu called "filter anonymous internet requests". If you want to access your camera from the internet you have to uncheck this option."I see this option in the WRT600N manual, but it references a software choice that I don't have.I have gone to the website and downloaded the latest compatible software version, and I still don't have the choice to uncheck this option.
View 2 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I have a Cisco Aironet 1041 , what a good repeater/wireless extender that works with it to cover an area of 50 squared meters ?
View 4 Replies View RelatedI have two access points that I recently purchased from ebay. I updated them both to c1140-k9w7-mx.152-2.JB and I have been unsuccessful at getting either of them to connect at faster than 39MBps. After scouring google for answers I found several with the issue of not using the correct WPA2/AES configuration and that was me. However after changing the configuration, I am still unable to connect to either of the APs at faster than the 39Mbps. [code]
View 4 Replies View RelatedI have 2 SSIDs mapped to 2 VLANs (other VLANs are configured, but not used) Security is set to WPA2
What do I need to change to get higher connection speed? What is the highest for this model? Why won't it let me select 40Mhz channel width? Telnet says on 20Mhz available (GUI says it is in "Least congested" mode even though it is not)
There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies View RelatedI'm about fed up with with having this issue that no one can seem to solve. It dates back to when I owned a WRT54G router. I started experiencing random disconnects with the router, both wired and wireless. I only owned the router a year and figured it was going bad.
So I purchased this WRT120N router late August. Soon after I set the router up, low and behold the same problem started. I've called my ISP a couple occasions and they tell me that everything is fine from their end. I've spoken with Linksys tech support on 3 seperate occasions. I have changed the MTU to 3 different values and upgraded the firmware. The 2nd support tech suggested that I do those two things. To my surprise this worked for 2 or 3 weeks with no problem. The same problem started again just last night disconnecting intermittingly. I spoke with another support tech and they suggested that disable the SPI Firewall protection and Anonymous internet request. That did not work for the brief time I had this disabled.
More into the problem, when it disconnects the modem seems fine but the activity light on it stops as it should. The router itself appears to reboot, then when it comes back up the connection restores. What could possibly cause this? I currently have version 1.0.02.This is getting very frustrating and I am getting very near not using Linksys/Cisco products any longer.
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedI have done a wireless site survey at a library and one AP541N will cover everything pretty well. They do have one spot where the radio strenth is not quite as strong, but you would never buy a second access point for just that one area. I did the SIte Survey using a 541N Access point.
Here is my question. I see that the Aironet 1041 is very similar in price and according to the documentation has a stronger power rating and higher antenna gain. Why would I not buy an Aironet 1041?
We are just mounting to a wall and are planning on using the pwrin4 to provide POE for whichever we buy.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedHotel only has a wired connection to the internet so I connect to it by ethernet cables.Can I turn then turn my pc into a router?So that I can use my pc as a wifi hotspot for my iphone/blackberry for example? or as a wifi for another laptop to feed through wirelessly?
View 1 Replies View RelatedRecently my friend has been telling me about all the information websites get from you. I knew they did, but the way he made it seem was that it's a very serious thing. I don't really want people to know what I do. I don't like them knowing where I live, ect. Is there anything I can run so that it reroutes me somewhere else and makes it seem like I am a different person so that the information they gather on me will make it seem like I am a person in Hawaii. or somewhere.
View 2 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View Related