Hotel only has a wired connection to the internet so I connect to it by ethernet cables.Can I turn then turn my pc into a router?So that I can use my pc as a wifi hotspot for my iphone/blackberry for example? or as a wifi for another laptop to feed through wirelessly?
View 1 RepliesI converted my old telephone wiring (Cat5e wire) to Ethernet by adding keystone jacks and then tied all the rooms together. I test every room for continuity with a LAN tester and everything showed up OK. I then plug my Ethernet in one of the keystone jack and check for internet in every room with my laptop received no connection. I connect the same cable to my laptop and everything works fine
View 18 Replies View RelatedI just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
I am trying to setup time service on two devices. Once is a UC520, the second an 1840 router. I would like to use the FQDN of the time server which is north-america.pool.ntp.org. This is the recommended procedure as per ntp.org due to changes of IP addresses of time servers.
On the UC520 this is not a problem. I type in "ntp server north-america.pool.ntp.org" and this is how the command stays in the config. On the 1800 the FQDN is resolved and inserted into the config as an IP address. This works for now but kinda defeats the purpose of using a FQDN.
How can I keep the 1800 from converting to IP?
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
I have successfully converted my lap1242ag-c-k9 to autonomous mode. But when i try to set ssid or wep then hit apply it won't the changes i made.
View 3 Replies View RelatedI have a wireless network using the cisco ap 1041 converted into the anonymous. however it seems like every morning or evening I have to attached it back to the SSID all over again. it will not give me an ip address. I also would have to put the encryption key in again. I am using WEP 40 bit.
View 4 Replies View RelatedI have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies View RelatedWhy there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies View RelatedWe have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies View RelatedIs the Linksys E4200 Dual Band Router compatible with DHCP and VPN?
View 1 Replies View RelatedThe router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies View RelatedThe standard Verizon router doesn't have Wireless N capability, so I got the WRT600N (first floor) a while back and connected it to one of the ports on the Verizon router (basement). I have the wireless turned off on Verizon router. My problem is that anything connecting to the WRT600N has extremely intermittent connectivity.
View 1 Replies View RelatedI just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies View RelatedI I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
View 5 Replies View RelatedBEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies View RelatedI currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedI have a Thomson TG585 v7 router which is in bridge mode. I also have a NetGear DGND3300v2 router which I would like to connect to the Thomson (eventually I will purchase a switch and connect another device along with the NetGear). The problem is that the NetGear only has 4 LAN ports and no WAN ports, which I assume you would need to set this up.
View 4 Replies View RelatedI have a Netcomm router which I've had working as my ADSL and my wireless AP.I connected a DLink router via ethernet so as to extend the range of my WIFI.This has worked, but now I cant log in to my DLink router.It started with IP 10.1.1.1After setting it up to not do automatic dhcp and then plugging it in to my Netcomm (which is on 192.168.1) I can no longer find the DLink, whether connected over ethernet or wireless. How it might have had its IP changed as it join the network?
View 14 Replies View RelatedUnable to access router admin page for Haier model R800
View 1 Replies View RelatedI have a WRT54GS which works fine with Linux both from both wired and wireless computers using Linux. But I reinstalled Win XP and now I can't reestablish a connection following the EasyLink advisor. I did have a connection under Win XP before.
The last instruction on the Easylink advisor tells me to look for something marked "local" I don't find that word on the screen.
I just reset my router to the factory settings in order to make some changes to it. However, when I tried to change the SSID to a unique name, I was unable to connect my computer to the wireless network. I then reset my security settings and left the SSID to the default name "linksys_SES_54125" and it is working just fine. I tried to connect with two separate computers both running Windows 7. My router is the WRT54G v8
why I wouldn't be able to connect to my wireless network when I change the SSID?
My home computer accesses the Internet through an ADSL modem and a phone line. I added a wired router (Linksys BEFSR41).I've since bought a laptop computer, an iPhone4 and a wireless router (Linksys WRT160N).Again, on the advice of a friend, I ADDED the wireless router, so now have two routers connected.The devices are connected as follows:
-Wall jack to ADSL modem
-ADSL modem to BEFSR41
-BEFSR41 to WRT160N
-WRT160N to desktop computer.
As I understand Linksys routers, the default IP address for ALL Linksys routers is 192.168.1.1.Both the iPhone4 and the laptop are unable to connect to the wireless router.I'm assuming the two routers are conflicting with each other, so I thought I would remove the wired router..Can I change the IP address of the BEFSR41 router from 192.168.1.2?
Would this resolve the conflict between the two routers and allow the wireless devices to "see" the wireless router? What's the correct procedure for removing the BEFSR41 router from the system?
There is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies View Relatedhad problem with isp after they fixed problem router shortcut disappeared
View 1 Replies View RelatedOk, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
View 2 Replies View RelatedHave an Actiontec GT704 feeding DSL into a BEFSR41 which is connected to a WRT610N. Can access internet, modem and wired router from desktop. Can access wireless router from laptop. Cannot access internet from laptop or wireless router from desktop. Changed ip address for wireless router to 192.168.2.1 so no conflict with modem or wired router.
View 3 Replies View RelatedIs it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies View RelatedRouter 1: I have a WRT120N wireless router connected to the Internet. It has IP 192.168.1.1 and DHCP is enabled with address range 192.168.1.100 up.
Router 2: I have a WRT310N router connected to the LAN via LAN port to ethernet jack in the wall (not WAN/Internet port). It has ip 192.168.1.2 and DHCP is DISABLED.
All the devices on my network can see each other. Devices connecter to router 1 can see devices connected to router 2.The problem is, devices connected to router 2 cannot get to the Internet. I verified clients connecting to router 2 are assigned the same DNS addresses and the same gateway 192.168.1.1 as the clients connected to router 1. But for some reason router 2 doesn't know how to router Internet traffic out through router 1?
I tried plugging the LAN cable into the Internet/WAN port on Router 2 but then devices on Router 2 can no longer see devices on Router 1. I've seen discussions of setting up router 2 on its own subnet: 192.168.2.1 instead of 192.168.1.2 but then supposedly devices on router 2 will still not be able to see devices on router 1.
I'm guessing router 2 can't access the Internet because it is default configured to send Internet traffic to the Internet port, no t the LAN port. how to configure it so all devices on both routers see each other and router 2 devices can get to the Internet.
I have an e2000 wireless router. I have the latest software version for the Cisco software.I have noticed that Cisco sets up the same password to access the router setup page as the wireless password..Anyone that connects to the main SSID will be able to connect to the setup page at 192.168.1.1...I know that I can change the password in the linksys setup page to whatever I want, but then when I open the Cisco software, it wants me to change the password to match what the administrator password is.Don't they realize that a wireless password is different than the Administrator password to access the router settings?
View 5 Replies View Related