I have got a cisco 887 router with ios CC880data-UniversalK9-M Version 15.0(1) M6. I am trying to enable sip alg and setup a class map for Stun nut the router does not support the command for stun.
View 3 RepliesI want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
[Code].....
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View RelatedWe have the below. Does this support Voice commands ? Or do we need a change of the router itself ? Or any licensing ?
C3825-ADVENTERPRISEK9-M, Version 12.4(24)T8
I am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
Whether ISE-3315-K9 with ise version: Service Engine: 1.0.4.573 , supports the command level accounting
Bascially , we have integrated Cisco Switches with Cisco ISE for Device Authentication using Radius , we are able get the authentication logs on to the devices , but for any command changes or update done on Cisco devices we are not able to get the command accounting.
I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies View RelatedWe are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
I use a C892 router with the IOS c890-universalk9-mz.152-1.T.bin. I just ran the command "debug ip packet 151 detail" and then the router stopped to work because it was overloaded. The ACL151 I used is as follow:
Extended IP access list 151
10 permit ip host 10.1.1.1 host 91.1.1.1
In the syslog then I got hundred of messages from IPSec:
Jan 11 09:43:35.677: IP: s=10.80.10.254, d=10.64.19.99, pak 8A7453CC consumed in output feature , packet consumed, IPSec: to crypto engine(70), rtype 1, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[code]....
For me it seems just like that this ACL is not applied and that I have a debug then for the whole traffic.
what happens internally when no shut command is given on the interface of router.The router interface goes up. How? What happen internally on the interface of the router?
View 8 Replies View RelatedWe have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
Is there any way to see on what ports a Cisco 5510router is listening to just like a "netstat -an" on UNIX would do. I could easily do a portscan to give me this report but would prefer having the information through a show command.
View 4 Replies View RelatedTransitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedI am trying to set up vpn tunnel between ASA and router C2921 for site-to-site routing. This was described on many sites. However I do not have required option under crypto command.
g1c1router1(config)#crypto ? key Long term key operations pki Public Key components
g1c1router1(config)#crypto
There are no crypto map etc options.
Some people suggested that I need crypto IOS. I have:
boot system flash:c2900-universalk9-mz.SPA.152-4.M3.bin
license udi pid CISCO2921/K9 sn FGL171910C1
Do I have to generate some keys? How do I do it? crypto key generate ?
My Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedIm having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View RelatedNeed to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
I am trying to enter a 'command' in what should be the diagnostics tab in other routers. Where I can enter this information in the new EA2700 advanced settings?
View 1 Replies View RelatedI need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
[Code].....
I need command for Script reboot (linksys E2000)
View 2 Replies View RelatedI'm probably overlooking something very simple but is there a command to show the uptime of a router interface in days,hours,minutes?
View 3 Replies View RelatedI am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedI have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View Relatedhow to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View RelatedI recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.
View 4 Replies View RelatedI got a Cisco 870 router. running C870-ADVSECURITYK9-M), Version 12.4(15)T7, does this support two link from different ISP.
View 2 Replies View Relateddoes Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies View RelatedI am trying to spec out some routers for a small DMVPN network.I was thinking 2801's for my hub routers.will these run DMVPN out of the box or do they need additional hardware modules?according to the below linkyou need a "AIM-VPN/SSL-2" module in order for it to work, but then according to"The Cisco 2800 Series supports IPSec Digital Encryption Standard (DES), Triple DES (3DES), Advanced Encryption Standard (AES) 128, AES 192, and AES 256 cryptology without consuming an AIM slot."
View 1 Replies View RelatedI was just thinking about this the other day, iirc I read somewhere about hooking up a dial up modem to the aux port on a router so that if your service failed you could dial the router directly to get access and diagnose faults.
Does anyone still do this? or do you use other methods? Cause it seems a bit old hat to me and I figured if you are paying a line rental on a phone line why not get dsl as well?
how many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View Related