Cisco WAN :: 3825 - Voice Command Support
May 19, 2013We have the below. Does this support Voice commands ? Or do we need a change of the router itself ? Or any licensing ?
C3825-ADVENTERPRISEK9-M, Version 12.4(24)T8
We have the below. Does this support Voice commands ? Or do we need a change of the router itself ? Or any licensing ?
C3825-ADVENTERPRISEK9-M, Version 12.4(24)T8
We recently purchased the Cisco Router 2951 router with the IOS 15.0. I have tried to put in my VIC2-4FXO card in it. When I did show invetery, it detected the card.[code] When I tried to configure the voice port by typing voice port, it shows % Invalid input detected at '^' marker. I have tried to reset the cad and replace with another one.
View 3 Replies View RelatedI want to know the number of routes supported by CISCO3825-HSEC/K9(512MB DRAM).
View 2 Replies View RelatedI have one 2821 router. Which ios will support both voice and vpn?
View 1 Replies View RelatedAny way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
Critical voice vlan feature, used to place a newly authenticating phone when radius server is dead into appropriate voice vlan, seems to be a new feature and I find the documentation to be incomplete. Do the following switches support this feature in any IoS versions? WS-C4510R, 4506, 3560, 3550,2960s.
View 1 Replies View RelatedI have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View RelatedThe Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View RelatedI have got a cisco 887 router with ios CC880data-UniversalK9-M Version 15.0(1) M6. I am trying to enable sip alg and setup a class map for Stun nut the router does not support the command for stun.
View 3 Replies View RelatedI am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
Whether ISE-3315-K9 with ise version: Service Engine: 1.0.4.573 , supports the command level accounting
Bascially , we have integrated Cisco Switches with Cisco ISE for Device Authentication using Radius , we are able get the authentication logs on to the devices , but for any command changes or update done on Cisco devices we are not able to get the command accounting.
I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
The process is IP Input and I'm not really sure how to troubleshoot it. I've read through all the doc's on high cpu load if I shutdown the port that feeds that network, CPU drops to around 30%, bring it back up and it jumps up to 90%+. I've got a policy map on the interface shaping the traffic
[code]...
I am trying to upgrade the IOS on cisco 3825 from 124-9.T1.bin to 124.24.t6.bin, after I upload the configuration to the CF and verify the file, everything appears fine but when I try to load the new image it fails with following error and falls back to old image :-
System Bootstrap, version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Readonly ROMMON intializedboot: cannot open "flash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "c3825-advsecurityk9-mz.124-24.T6.bin"
Then after few minutes it boot to the Old 12(4).9 ios again.
What are the prerequisites before doing this? I have to upgrade a router this Wednesday evening if there is an opportunity to move it to a code that is more current that the one the client is currently running which is 12.4(25b). I see on the Cisco Support site that after this code, everything moves to 15.
View 5 Replies View RelatedI have a 3825 with a 16 port etherswitch card installed that I'm trying to setup rate-limits on. Interface G0/0 is the connection to the outside world and int g0/1 has a couple of 2950 switches attached to it.
The etherswitch card, f1/0, f1,1 etc has corresponding vlans, 902, 903 etc each with an IP 10.110.1.x, 10.110.2.x and all part of access-group 111. The switches connect on sub-interfaces g0/1.101, g0/1.102 etc and have IP's 10.55.1.x, 10.55.2.x and part of access-group 101.
What i'm trying to achieve is that every port / IP that is on access-group 111 shares 3Mb of bandwidth in/out and access-group 101 shares a separate 3Mb of bandwidth in/out.
I've created two access-lists as follows;
access-list 101 permit ip 10.55.0.0 0.0.255.255 any
access-list 111 permit ip 10.110.0.0 0.0.255.255 any
And on int g0/0 I've created the following rate-limits;
rate-limit input access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit input access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
Now instead of both access-groups having 3Mb each they all seem to be sharing 3Mb! I've tried class-maps and policy-maps but to no avail..
LAN subnet conflicts with WAN subnet. My router is d-link 825 and my cable modem is Cisco EPC-3825. Op system is W7. Everything worked great with an older cable modem (Cisco 3000).
View 4 Replies View RelatedIs there any way to configure 3825 to ensure that all packets have a source IP address that matches the correct source interface (similar to ASA's 'ip verify reverse-path interface')? Currently, we manage anti spoofing with a bunch of ACLs, however I'm looking for a more manageable solution.
View 2 Replies View RelatedI want to configure PAT on the router I have no configuration yet
View 1 Replies View RelatedWe need to upgrade the RAM on our 3825 Cisco Router. Currently, it's 512MB and we want to upgrade it to 1GB. So do I just order another 512MB DRAM Memory? What is the part number that I need to order?
Here is the show ver:
Cisco IOS Software, 3800 Software (C3825-ADVENTERPRISEK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 19-Oct-09 21:05 by prod_rel_team(code)
am downloading 3825 security IOS there are two IOS of advance security, am confused what’s the difference in both Advance Security Image
ADVANCED SECURITYc3825-advsecurityk9-mz.124-15.T7.bin.ASK9-ASK9 FEAT SET FACTORY UPG FOR BUNDLESc3825-advsecurityk9-mz.124-15.T7.bin
This is a multi site network. Site A has a Cisco 3825 router and connects to 3 other sites over ISP A and 2 other sites over ISP B. Both ISP A & B provide a layer 2 full mesh network. ISP A provides a 100mb pipe while ISP B provides a 20mb pipe.
File transfers (Windows - CIFS) over ISP A's fiber are fast enough and throughput is good. However, file transfers (Windows - CIFS) over ISP B's fiber are slow, even though latency is good. On the 100MB ISP A pipe, file transfer speeds up to 6 M Bps are achieved. On the ISP B 20MB pipe, speeds up to 300KBps are seen for file transfers.
ISP A connects to an on board gig port on the 3825. ISP B connects to a fast ethernet port on an HWIC-2FE card on the same 3825. Both ports then connect to ISP Switches and then full meshed to remote site Cisco routers. What could be the issue? Why am I facing these issues only with ISP B even though the configs for ISP A and ISP B are the same?
we have some unusual issue when our core 3825 series router dealing with NAT !first off to offload traffic we have two router one 3825 and other 2821 configured to support GLBP .
interface GigabitEthernet0/0
ip address a.b.c.d 255.255.255.0
ip nat outside
ip virtual-reassembly
[Code]....
The problem is router hangs out , intenet users suffer slowness , criticle service like telnet doesnt work . the only solution i found is a reload ,not to mention this is core router sitting on campus network edge . and servicing around 1000 users !! approx assuming all users have using internet at same time .
how to check , if memory is not sufficient ?further if any users using utorrent or any thing like that , does it make enormous no of connections form same pc ?
is their any licence requird for IOS IPS ?i prefer to turn this feature on to kill torrents connections ? but i fear crashing of router as no of users are huge !any know bug with glbp , nat with ip voice image C3825-IPVOICE-M VERSION 12.4(24) T4 ???
I have 3825 router with flash size 128 and 512 RAM.i am trying to install a VIC3-2FXS on the router.the FXS is know by the router when i put show version or show diag,unfortunately the FXS is always showing orange light.i tried to upgrade the router to c3825-advipservicesk9-mz.124-20.T.bin and to c3825-advipservicesk9-mz.151-1.T3.bin with same result.
View 1 Replies View RelatedI have a 3825 with a 1Gb fiber card at one of my sites. Our ISP and MPLS provider hand off a single gigabit fiber to us that contains 2 50MB EVC's.I need to apply QoS to one of the EVC's and shape them both to 50Mb to avoid upstream rate mismatch bottlenecks. Both of the EVC's generally only push 10Mb during business hours.When I run UDP stream tests (various rates from 500k-6m that are marked as AF41) to one of my other sites I am consistently getting about 2% packet loss, despite the fact the circuit isn't even close to 50% saturation. When I remove Shaping and QoS all together, the issue nearly clears itself up, except during peak hours and I get small bursts of packet loss, which is still unacceptable.When the pipe is at near zero utilization (after hours) there also is no packet loss with or with out the shaping/qos applied.
View 1 Replies View RelatedWe use a 3825 router to screen alot of the junk from the internet side or our firewall. Its worked well for the last 4 years buthas rebooted multiple times in the last month for no apparent reason.At this point I think I would prefer to replace it.Our current internet link is 100Mbps and this router handles that quite well. Is there an equivalent that I should replace it with, or should I just buy another 3825 ?One with an OOB management port would be nice.
View 6 Replies View RelatedI want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies View RelatedI have a remote customer who is having issues with their 3825 router - since I can't be on site troubleshooting is difficult but so far all that seems to happen when the device is powered on is the "SYS PWR" light goes solid green, and no other lights come on. Fans seem to be operating normally. Console access doesn't appear to be working.
View 2 Replies View RelatedI have a 3825 configured as an EZVPN server with 881 routers as clients. One issue I am seeing is that sessions don't seem to time out, such as when a peer's public IP changes. Show crypto ISAKMP peer shows the same host (using device certificates for authentication) with multiple public IPs establishing sessions. I have ISAKMP keepalives configured on the router.
View 2 Replies View RelatedI want to configure HSRP between two different series routers. In my case the router are 3825 and 3925.
View 7 Replies View RelatedI have a NMWLC6 module connected to a 3825 ISR using 1140N APs. Latest (but one) code. I had two SSIDs configured and deployed in the default AP group. Last week I needed to deploy a third SSID for unencrypted webauth, I created the interface and WLAN associated with the interface and the sub interface/svi on the WLAN-controller 0/1 with dot1q. All created with no problem and enabled, however the SSID was not available to clients and did not show up as available WLANs under AP groups menu. Out of desperation I created a new AP group and added an AP to it and hey presto all three WLANs were available and the third is now visible to clients! Is this normal behaviour? Is the default AP group limited to two SSIDs? (a quick google failed to find any documented limitation!) or is something weird going on?
View 2 Replies View RelatedI have three Hub routers that I'm wanting to compare DMVPN scalabiltiy capabilities (3825 versus 3945 and 3845). I know it must be there somewhere and I'm just not looking in the right place. But I've read and read and read about DMVPN designs and I'm not finding anything. This is turning into a time killer. What are the DMVPN limitations of these three routers are?
View 6 Replies View Related