I am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
I need to know if Cisco Switch 2960 support Netflow. If it doesn't, how do I configure the switch to enable Netflow?
View 3 Replies View RelatedI can't seem to find any information on the Nexus 5000 support of netflow. I assume that means it doesn't do netflow.
View 5 Replies View RelatedI'm looking at implementing a new DMZ and wanted Netflow capability for security monitoring.The architectural principles I have to adhere to dictate that the switches within the DMZ are layer 2 however to get Netflow I need a minimum of a 3560/3750X, Network Services module, IP Base IOS with ip routing and CEF enabled.To do this and still keep the switch functioning as a layer 2 device the intention was not to configure SVI's or any static/dynamic routing protocols.Will Netflow still work in that scenario?
View 4 Replies View RelatedI know the Nexus 5548P hardware does not support Netflow.I just need to know that if we introduce the layer 3 Daughter Board N55-D160L3 does this add Netflow support?
View 3 Replies View RelatedI've been researching the 3750-x Netflow support but I'm not 100% sure of how much support it has. From what I've read the only way to get NetFlow support is to install a specific module that provides NetFlow. I also heard about how it might support s-flow but I haven't found out for sure.
View 8 Replies View RelatedI have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
Currently i've a cisco ws-c4506-e edge swith loaded with cat4500e-ipbasek9-mz.122-53.SG4.bin image file. Can i use this image file on a ws-c4503-e as well?
View 1 Replies View RelatedAny major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedDo you know if the following Cisco switches ME3600X ME3800X support Netflow? I need to collect data on interfaces and export it to an external Netflow collector installed on a server. In other word, I need to be sure that those switches support the following command (or similar):
ip flow-export destination <IP> ip flow-export source <Interface> ip flow-export version 5 ip flow-cache timeout active 1 ip flow-cache timeout inactive 15 snmp-server ifindex persist !
[Code].....
What are the limitations of Net flow v9 support on the 7600 platform for the SR code releases?
I know that Flexible Net flow is only available on newer releases with some newer hardware. Flexible Net flow gives you the ability to provide full support for Netflow v9 as well as IPFIX.
However, the documentation indicates that Net flow v9 is still supported in the SR code. So I am just trying to find out what are the limitations in how Net flow v9 is implemented without "Flexible Net flow". The Cisco TAC was unable to provide me any documentation about this.
I was working with Opmanager software to monitor my network, and i downloaded the Netflow plugin, i tried to enable the netflow on my core switch c3560 but I was surprised that it does not support the NetFlow, after many resersh most of URL's say it does not support until i found another URL from Cisco Says that it support Flexble netflow now, but i think we should update the IOS.
[URL]
I currently have Netflow enabled on all of my routers in my network. However, I have a Cat3750, which does not support Netflow. The 3750 is at a larger remote site and I need visibility into the traffic that is traversing internal to that switch. All VLANs are configured on the 3750. I have an extra Cisco router, which I have theorized I could use as a Netflow probe.
The 2811 Router has to FastEthernet ports.F0/0 would be configured with no IP Address and would be connected to the 3750 on G0/1 with no VLANs configured.F0/1 would be configured with a static IP and connected to the 3750 on port G/02 with the appropriate VLAN to ensure network connectivity.
On the 3750, configure a monitor session with a destination of Interface G0/1.On the 2811, configure netflow to sent to the Netflow server and set F0/0 for ip flow ingress.Obviously, it doesn't work. But I cannot figure out why.
I searched around but did not see any valuable info on this so I guess it doesn't. But wanted to get confirmation from you guys.
View 2 Replies View RelatedI have a SR520 just deployed at a remote site with Internet Access.
Working Environment:
Remote sites have SR520 with IPSEC VPN back to HQ and netflow v.5 works through the VPN back to our PRTG server.
Non-Working:
I cannot get Netflow data to our PRTG with this first SR520 implemented with Zone Base Security. I am not able to get my netflow traffic out. VPN is up and running. Internet is a dialer0 interface. I have a Kron job that does the copy run to tftp backup daily to the same PRTG server and it works fine.
Both my source interface and address on the TFTP command and the netflow commands are the same interfaces (VLAN75) and IP. The Destination ip is the same too (through the VPN tunnel).
Snipped:
flow exporter prtg
destination x.x.x.x
source Vlan75
[Code]....
I am trying to figure out the Flexible Net-flow on Cat 4510R+E Switch running IOS-XE code. My Neflow flow software is manageengine 7.X. I am able to see the netflow interfaces but the traffic itself is not displayed. On the Switch I can see the netflow exporter statistics counter being incremented thereby confirming as being exported.
View 2 Replies View RelatedI have a 370 with C3KX-NM-10G module & i want to enable NetFlow on it did the specified configs
Step 1 Flexible NetFlow Flow Recordsflow record miketestmatch datalink source-vlan-idmatch datalink dot1q prioritymatch datalink mac source-addressmatch datalink mac destination-addressmatch ipv4 versionmatch ipv4 tosmatch ipv4 ttlmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport source-portmatch transport destination-portmatch interface input physical snmpcollect interface output snmpcollect counter flowscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime last flow record miketestegressmatch datalink destination-vlan-id match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 version match ipv4 tos match ipv4 ttl match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port match interface output physical snmp collect interface input snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last Step 2 Flexible NetFlow Flow ExporterFlow exporter export-to-samplicatorDestination 10.1.1.8source Vlan1Transport udp 2055option interface-table timeout 60 Step 3 Flexible NetFlow Flow Monitors# Tie the Flow Monitor to the Flow Recordflow monitor mikektestrecord miketestexporter export-to-samplicatorcache timeout active 60flow monitor mikektestegressrecord miketestegressexporter export-to-samplicatorcache timeout active 60
& Applied it to g1/1/1 but without any luck , if netflow works on the
TenGigabitEthernet1/1/1 &
TenGigabitEthernet1/1/2
Only i have four switches stacked and nothing plugged to the
C3KX-NM-10G module
router 7200 (12.2(33)SRE1)
two interfaces with traffic going through, placed in a Data-VRF
Another physical interface and loopback interface in the global routing-table.
ip flow ingress on all physical interfaces configured
It was running for at least a year: I was getting netflow packets on my analyzer from the box. Since a couple of weeks I get no netflow-packets anymore.debug ip flow export tells me "IPFLOW: Sending export pak to ... port 2055"
But the packet is not leaving the box. By setting up an ip sla monitor udp-echo I simulated some traffic (udp/2055) which is leaving the box.
[code]...
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
Ive tried to configure NetFlow on layer 2 without success. I configured the recondmonitorexporter like the configuration guide said. but still i dont receive any netflow traffic. I checked the firewall on the VM and it looks fine.
i have done the command under the ethernet interface :" layer2-switch flow monitor TEST input" - for layer2 input.
Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 Replies View RelatedIf a Supervisor 6-E will support NetFlow on a Catalyst 4507R-E?If not, what are my options for NetFlow on a 4507R-E?
View 7 Replies View RelatedTo enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies View RelatedIt is possible to configure the IOS NetFlow 122-58.SE2 in a Catalyst 3560?
View 5 Replies View RelatedI have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View RelatedWe have Cisco Catalyst 6509-V-E VSS Switch with Sup2T und IOS Version 15.0(1)SY2. We are gettin input netflow information from the gi2/3/7 but not output ... I am not sure why it does not work.
View 1 Replies View RelatedHow to get a summary of netflow statistics on NX-OS? On IOS you could do sh ip cache flow which would show what I need? Can't find a similar command on the Nexus Platform.
View 4 Replies View RelatedI have problems in exporting translations of NAT from my router through NetFlow v9 ASR1006, to my server nfdump, any opensource or licensed software (collector) that I recommend.
ip nat log translations flow-export v9 udp destination 10.1.1.15 1181
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
I have a problem with the 6500 not exporting netflow data. They are not exported due to no fib.I have read somewhere that this has something to do with VRF. VRF are running on the router.ip flow ingress has been applied to desired ip int.Is there anything I could do to make it export netflow data?
VSS-core-XXX-rs1#sh ip flow export
Flow export v5 is enabled for main cache
Export source and destination details :
VRF ID : Default
Source(1) xxx.xxx.83.253 (Unknown)
[code]....
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....