I am trying to enter a 'command' in what should be the diagnostics tab in other routers. Where I can enter this information in the new EA2700 advanced settings?
View 1 RepliesI'm having issues with a newly bought EA 2700 router, I'm getting disconnected every 30-60 minutes. (It's a brief disconnect for about 10seconds, perhaps a huge packet loss or something?)I've tried connecting directly to the modem and that seemed to have fixed the problem, so I think that it is a router issue...? Also, my download/upload/ping is 35mbps download, 35ish mbps upload, and 8ms. (I have a 35mbps connection so that's fine) But when I connect my PC to the modem directly, my MS becomes 5, and my upload jumps to 77mbps. The download stays the same...
View 9 Replies View RelatedWhy is the 2700 faster if the 3500 is more expensive ? 2. will cisco put out a firmware that allows me to block more then 100 urls and keywords cuz as it is now i find that limiting it to only 8 urls makes the new linksys routers useless and NO i wont use opendns they are slow and charge you to remove the ads thats why i use the keyword blockin to block popups and ads 3.will a firmware upgrade make the 3500 faster then the 2700 later on ?
View 4 Replies View RelatedI have two Cisco Location Appliances 2700 devices that has version 6.0.101.0 on. I'm having problems getting it to work. Any that can assist with this?
View 1 Replies View RelatedThe compatibility matrix shows no support for a Location Appliance 2700 for any version 7.0.x.x for WCS and WLC. However, I did see a thread here where a v6.0.x.0 had compatibility. v6.0.202.0 is MD. Is it compatible with v7 WCS and WLC?
View 3 Replies View RelatedWe plan on buying a Cisco 2700 wireless location appliance but I need to know if it will be compatible with our 2500 WLC.I've tried to look but cant find any document for this. Also can you deploy the location appliance without a WCS?
View 7 Replies View RelatedI need command for Script reboot (linksys E2000)
View 2 Replies View Relatedhow to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View RelatedI recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.
View 4 Replies View RelatedRegion : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : India
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968
Code:
Pinging 10.0.0.1 with 64 bytes of data:
Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1
Ping to Internet
Code:
Pinging 8.8.8.8 with 64 bytes of data:
Request timed out.
We have an SRP541W on which I thought I had disabled DHCP, its turns out that in fact I haven't. After seaching again for the DHCP on/off funtion I found it under the Vlan settings (Wierd place to put it I thought).
The Router has a static ip address on the LAN side of 192.168.1.254 and is connected to a Cisco 2700 series on the WAN side. Our network DHCP is served by an SBS 2011 server hence my reason to switch off DHCP on the router. However when I select Static IP address from the Address Type in the VLAN settings and try and save the changes I get an error that is IP Address / Subnet Mask value is illegal. Great but why when the router has and IP address assigned and the subnet mask is set do I get this error. On the VLAN settings page there is no option to set an IP Address
I would like to explain my situation. My house has 2 floors. My broadband modem is on the 2nd floor. I have an ea 2700 linksys router there, connected to the broadband modem. However, i can't get a good wireless signal on 1st floor, therefore i bought a second router, an e 4200 linksys.
I searched the web, and connected both routers via Ethernet cable, plugging them in lan ports. The ea2700 was only configured wireless security passwords. The e4200 had it's ip renamed to 192.168.1.2 and DHCP server turned off. Well, i have a problem here. the second router, doesn't give me access to internet.
I am Using Windows 7 32-Bit, and my Network usually works fine, and my internet has been working fine up until recently. However about a month (maybe more) I noticed a problem that kept cutting me off occasionally and said Diagnostic Policy was not started, I troubleshooted it and it was fine. Much more recently this has been happening more frequently and troubleshooting it doesn't solve the problem. I can get online for 10-15 Mins then I am cut off again. Restarting the computer often fixes it but not always. I went to Services and found the Diagnostic Policy Service is not running, I press start and receive this error message.
The Diagnostic Policy Service service on local computer started and then stopped. Some services stop automatically if they are not in use by services or programs.I am quite sure my loss of Internet is due to this as this is a network related service and what the troubleshooter always finds to be the problem. Other Computer/Devices in the house connect to the internet fine with no loss of connection so it has nothing to do with that. I have tried various fixes like uninstalling network adapter drivers, and checking permissions in Registry but it has not worked.
I think I may have a bad port on a 5548, does the NX-OS has any sort of self-diagnostic test on its port?
View 6 Replies View RelatedWhat you can try:Diagnose Connection Problems,This is what is displayed evry third or fourth page when I surf...I could just be finishing a survey and bam this pops up and when you have 56 K dial up and your computer is already slow, you dont need this slowing you down....what can I do ? I am afraid to do my online banking....
View 11 Replies View RelatedI have "Xtreme" internet service with Time Warner Cable, and it isn't so Xtreme. The modem/wireles router is the Ubee DDW3611.I was doing some work earlier this morning, and the lawn mower guy was here in the back doing his thing. All of a sudden the internet goes out. I see that damn dreaded yellow exclamation mark in the taskbar superimposed over the wireless internet icon. My first thought was that the lawn dude ran over some wires.I went outside to see if any wires were exposed or had been damaged. I noticed about a yard of wire was exposed above ground, but did not appear to have any damage.Anyway, I've been trying for the past few hours to fix this darn thing (before the technician gets here around 4pm). I've tried all the simple stuff like reset the modem, restart, mess with dns settings, but I have no idea where to go after this.
Here is what I get when I go to cmd > ipconfig /all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Xenfi_Javier
Primary Dns Suffix . . . . . . . :
[code]....
We have two C2960s switch stacked and I have started a full diagnostic on them.
We have receive a failed result with the tests details Test: TestPortAsicCam, Result: Failed Is there possible to receive a diagnostic of this failure
dhcp server failed while running network diagnostic test for windows xp
View 1 Replies View RelatedWe just replaced our Cisco 1240 AP in one of our shops with a Cisco 1141 AP. This is not controller based.
We use several wireless (infrastructure mode) auto diagnostic tools which connect to the AP. We also have many laptops which run the diagnostic software.
We had no problems with our 1240AP. With our 1141, we cannot connect to the wireless tools if both the laptop and the tools are connected to the 1141. If I connect one to the 1240 and one to the 1141, they can see each other and work fine. IF they are both connected to the 1141, they show up as connected in the AP, they can ping each other, but the software does not communicate.
[URL]
I want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies View RelatedThe following error was seen on the switch and the Diagnostic Test Loop back failed following a new WS-6748-SFP module installation.Fabric in slot 5 detected excessive flow-control on channel 3 (Module 4, fabric connection 1)
Tried Hard reset of the module and still the error persist.
I installed WS-C4506-E 3 day ago. I discovered someting different module status Right at the end of the module ( WS-X4648-RJ45-E ) show red led. this is not port led i try to reset module several time. but it's same status. but this is operating now nomally I upload picture.. and this is module status and diagnostic result
Error code ------------------> 3 (DIAG_SKIPPED)
This Case is DOA(Dead of arrival ?
C4506#sh modChassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E ABCDE1234562 24 1000BaseX (SFP) WS-X4624-SFP-E ABCDE123456 6 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E ABCDE123456
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 b0fa.ebe5.16c0 to b0fa.ebe5.16c5 1.1 15.0(1r)SG3 03.03.00.SG Ok 2 b0fa.ebc6.5b70 to b0fa.ebc6.5b87 1.2 Ok 6 10f3.1197.1490 to 10f3.1197.14bf 2.1 Ok
[code]....
I had a sw/reset on my 6509 switch. The info in the crashinfo file pointed me to bug CSCso89550.
The workaround for this issue is to disable the gold diagnostics tool.
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View RelatedNeed to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
is it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?
View 3 Replies View Relatedwhat happens internally when no shut command is given on the interface of router.The router interface goes up. How? What happen internally on the interface of the router?
View 8 Replies View RelatedI have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies View RelatedWe are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
I have got a cisco 887 router with ios CC880data-UniversalK9-M Version 15.0(1) M6. I am trying to enable sip alg and setup a class map for Stun nut the router does not support the command for stun.
View 3 Replies View RelatedI use a C892 router with the IOS c890-universalk9-mz.152-1.T.bin. I just ran the command "debug ip packet 151 detail" and then the router stopped to work because it was overloaded. The ACL151 I used is as follow:
Extended IP access list 151
10 permit ip host 10.1.1.1 host 91.1.1.1
In the syslog then I got hundred of messages from IPSec:
Jan 11 09:43:35.677: IP: s=10.80.10.254, d=10.64.19.99, pak 8A7453CC consumed in output feature , packet consumed, IPSec: to crypto engine(70), rtype 1, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[code]....
For me it seems just like that this ACL is not applied and that I have a debug then for the whole traffic.
We have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
Is there any way to see on what ports a Cisco 5510router is listening to just like a "netstat -an" on UNIX would do. I could easily do a portscan to give me this report but would prefer having the information through a show command.
View 4 Replies View Related