I have two Cisco Location Appliances 2700 devices that has version 6.0.101.0 on. I'm having problems getting it to work. Any that can assist with this?
View 1 RepliesWe plan on buying a Cisco 2700 wireless location appliance but I need to know if it will be compatible with our 2500 WLC.I've tried to look but cant find any document for this. Also can you deploy the location appliance without a WCS?
View 7 Replies View RelatedThe compatibility matrix shows no support for a Location Appliance 2700 for any version 7.0.x.x for WCS and WLC. However, I did see a thread here where a v6.0.x.0 had compatibility. v6.0.202.0 is MD. Is it compatible with v7 WCS and WLC?
View 3 Replies View RelatedI upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?
View 2 Replies View RelatedWe have an ACE Appliance in a DMZ and the ACE Appliance's Admin Context IP is translated between ACE and ANM. The ANM Server does not get translated. It is just the opposite then in another Community discussion.
Our Problem: When adding the ACE4710 Appliance to the ANM imported Device List, we use the ACE's NATed Admin Context IP. Import works well, but ANM reflects the Admin Context IP with it's real configured IP. Polling the ACE Appliance does not work therefore.
Is there a possibility of telling the ANM, that the ACE has to be polled through a NATed IP? I could not find a field to set a NATed Mgmt IP.
Configured IP on ACE Admin Context: 192.168.0.10
NATed ACE Admin Context IP: 172.16.0.10
Imported ACE with IP 172.16.0.10 into ANM, but ANM polls for Rserver, Vserver, Probes, etc. via 192.168.0.10 - which is not reachable from the ANM.
I am trying to enter a 'command' in what should be the diagnostics tab in other routers. Where I can enter this information in the new EA2700 advanced settings?
View 1 Replies View RelatedI'm having issues with a newly bought EA 2700 router, I'm getting disconnected every 30-60 minutes. (It's a brief disconnect for about 10seconds, perhaps a huge packet loss or something?)I've tried connecting directly to the modem and that seemed to have fixed the problem, so I think that it is a router issue...? Also, my download/upload/ping is 35mbps download, 35ish mbps upload, and 8ms. (I have a 35mbps connection so that's fine) But when I connect my PC to the modem directly, my MS becomes 5, and my upload jumps to 77mbps. The download stays the same...
View 9 Replies View RelatedWhy is the 2700 faster if the 3500 is more expensive ? 2. will cisco put out a firmware that allows me to block more then 100 urls and keywords cuz as it is now i find that limiting it to only 8 urls makes the new linksys routers useless and NO i wont use opendns they are slow and charge you to remove the ads thats why i use the keyword blockin to block popups and ads 3.will a firmware upgrade make the 3500 faster then the 2700 later on ?
View 4 Replies View RelatedWe have an SRP541W on which I thought I had disabled DHCP, its turns out that in fact I haven't. After seaching again for the DHCP on/off funtion I found it under the Vlan settings (Wierd place to put it I thought).
The Router has a static ip address on the LAN side of 192.168.1.254 and is connected to a Cisco 2700 series on the WAN side. Our network DHCP is served by an SBS 2011 server hence my reason to switch off DHCP on the router. However when I select Static IP address from the Address Type in the VLAN settings and try and save the changes I get an error that is IP Address / Subnet Mask value is illegal. Great but why when the router has and IP address assigned and the subnet mask is set do I get this error. On the VLAN settings page there is no option to set an IP Address
I would like to explain my situation. My house has 2 floors. My broadband modem is on the 2nd floor. I have an ea 2700 linksys router there, connected to the broadband modem. However, i can't get a good wireless signal on 1st floor, therefore i bought a second router, an e 4200 linksys.
I searched the web, and connected both routers via Ethernet cable, plugging them in lan ports. The ea2700 was only configured wireless security passwords. The e4200 had it's ip renamed to 192.168.1.2 and DHCP server turned off. Well, i have a problem here. the second router, doesn't give me access to internet.
I'm essentially looking to extend an existing network in a primary warehouse for our company across a parking lot to a secondary warehouse with no network drops. I need to keep the ability to assign addresses in the existing scheme over to two computers in the secondary warehouse.
View 1 Replies View RelatedI'm looking for getting a Cisco prime NCS appliance (PRIME-NCS-APL-K9). I'm a little bit confused regarding to the license scheme:
1. Does the appliance has any license coming with it or we need to order the license separately?
2. If I have an WLC 5508 (license support 12 APs) & 12 3500 APs, then number of devices counted will be 1 (WLC) or 12 (APs) or 13 (WLC + APs) ?
We have 2 5508 WLC's on site (5508-1 & 5508-2) and at the completion of this project we will have around 150 access points. We are also using WCS. 5508-1 is set as the primary/master controller. 5508-2 is the secondary controller, serves as backup if/when 5508-1 fails. All LAPs connect to 5508-1 by default, so 5508-2 is basically sitting there doing nothing. Is this the best way to take advantage of the resources that are available? Would wireless clients see improved performance if the access points were split between the two controllers? If we do split LAPs between the controllers should I make sure that all of the LAPs on a particular floor are connected to the same controller or does that matter?
View 7 Replies View RelatedI have 2 Cisco WLC 4400's connected to a WCS. I want to use this Location Tracking feature within the WLC 4400s so that i can track movement of particular network devices throughout my facility. I cannot find anything on how to set this up on the internet. I found a PDF explaining the 4 different ways you can track objects but nothing more.
Is this service still supported in the newest versions?
where is the button to turn on the wireless for a HP 2000 notebook pc?
View 1 Replies View RelatedI will be staying at a rental property that has ethernet cable & modem. If I bring my E4200 v2 router from home & connect it to their modem, will my Toshiba 16GB Thrive be able to access the internet via WiFi? When I initially set up the router, I ran the router CD on my laptop, and the Thrive automatically accessed the internet. Will the Thrive automatically do the same when I connect the router at the new location. There is no computer there to run the router software. Will the the network be secured as it is at home? Same network name & password?
View 1 Replies View Relatedusing a Cisco 5508 controller (code version 7.4.100.0) with an ACS appliance running version 4.1 or 4.2?I've found that the ACS constantly reports a 'Bad request from NAS' (Invalid message authenticator in EAP request). message. This usually indicates a mismatched shared secret but this isn't the case.The controller works fine opposite a Microsoft NPS Radius Server.
View 6 Replies View RelatedI have a existing wireless setup of 4400 WLC with some AP's connected remotely,now i am migrating the whole setup to the new WLC 5500. All the AP has been registered to the new WLC 5500 except the remote location AP's.As there was no option of giving IP address in GUI of the controller in 4400 WLC, i have changed the controller name and restarted the AP, but even though it is going back to the old controller.
View 15 Replies View RelatedI am trying to set a wireless connection and it says that the Wifi isn't on, which I believe, because I don't even know where the Wifi button is. And the computer didn't come with an owner's manual with a diagram of where and what every button is. Trying to set up PC for bf for Christmas. I am a mac user :P so I have lost my touch with PC's.
View 1 Replies View RelatedHow to connect laptop#2 to wireless router when you donot know security key code?
View 2 Replies View RelatedUsing win7 64 bit 1 pc upstairs and laptop down stairs,no need for file or printer sharing so its disabled. Is it right that the public location setting is the safest setting with the sharing option disabled,and that wpa etc is not used, If you know you won’t need to share files or printers, the safest choice is public network.
View 6 Replies View RelatedWhere is wireless on/off switch for Inspiron E1705 with Dell wireless 1500 Draft 802.11n WLAN mini-card? I'm told the wireless card has been turned off. It shows as enabled and working in Devices.
View 12 Replies View RelatedWhile trying to connect to WiFi at remote sites APs, the connection is getting time out.User are getting error as 'Unable to connect to <WiFi-SSID>' The APs at corporate office are functioning properly and user are able to connect to the APs.
Wifi Controller: 2504 Software ver: 7.3.101.0
Authentication 802.1x
I have wireless N router and just got wireless G usb adapter... but i dont get it to work.... can i manage to get it working or i need another adapter?
View 2 Replies View RelatedI recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?
View 6 Replies View RelatedWe have a client that moved to a new office and WAP4400N can no longer reach entire office so we need to put in repeater. However, we have already tried one that isn't compatible so which model of wireless repeater is compatible with WAP4400N. Note, we do not use Wireless N and will not be any time soon due to older devices.
View 1 Replies View RelatedI have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies View RelatedHave just received an AOL wireless modem; have a belkin wireless adapter for my PC (running Wndows XP) but doesn't give a reliable connection to AOL.Is there any specific adapter I should be using? Modem isSL 2680
View 1 Replies View Relatedif the Cisco Power Injector (AIR-PWRINJ3=) is compatible with the 541n AP ? I find info about compatility with other AP models but didn't find any related with this SMB model.
View 2 Replies View RelatedLooking to set up a small office cheaply and quickly and was thinking about ordering a 2006 and some 1130s off EBay. Are the lightWeight 1130s compatible with the 2006?
View 9 Replies View Relatedi have MiFi2200 internet service .when router is down stairs in main part of house , signal is weak upstairs on desktop. i am using Linksys speedbooster on desktop to receive wifi signal. what can i do to increase MiFi signal to upstairs desktop computer?
View 1 Replies View RelatedI have just spent an hour with TalkTalk technical support being told that the new router they supplied today can only be used wirelessly for Vista or W7 but not both together. Am i going mad. Both connect to the router but my Vista laptop will not connect to the internet and will only show as an unidentified public network.
View 5 Replies View RelatedI was successful in configuring a new e1200 in bridge mode to extend my network. I did this with the routers side by side. In then moved the e1200 to a new location 150 feet away and it will not work. I previously had this working with an older linksys router. It will not deliver a Internet connection.
View 8 Replies View Related