I've just reformatted my computer and reinstalled windows xp but i can no longer find the window where you search for available wireless networks. It used to be a little icon in the bottom right of the task-bar.
I understand that the PCEX-3G-HSPA requires and a sim card. I also have a PCEX-3G-CDMA-V. Does this require a sim card as well? And if so, where is the sim card installed?
Within the space of a few days we've had 2 HWIC-3G-HSPA-G cards appear to fail on different router models. In each case the sh cell x/x/x hardware output is empty i.e no firmware version or other data provided and the radio status is off. Attempts to force the interface down using the test ....modem-power-cycle or radio-power off get the same error message that the modem is still in reset. Reloading the router does not clear this so we recently tried to update the firmware using the latest version off CCO. The upgrade using the microcode commands failed with an error of "unable to determine the modem state".
We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
I want to use cisco connect with the Router E1200. There is a wireless connection between laptop and E1200 Router. When I run the "Cisco Connect" after couple minutes searching It can not find the Router and I have to put an (Router name SSID) and password.
We have an ACS 5.2 server connected to an AD domain controller which has several trusted domains. (domain1, domain2, domain3) We currently have to specify which domain each user belongs to (ie, domain1user) in order to connect. We would like to only have to enter the user name without the prefix, (ie, user1) and have ACS automatically check each domain for a match. Is this possible with ACS 5.2? I seem to remember this was possible with ACS 4.2.
I have an application for work that I need to access true vpn connection :I have Sbs server 2008 with vpn support , I can access my folders and exchange and ... , this works fine.Now I have an application that search to connect to the server via local ip at work but when I use vpn to access it then the application goes searching on my local ip adress and not on the vpn ip adress.vpn has same ip as local ip at work).Now my question is: Can I set the application to search on the range of my vpn connection instead of searching on my local ip when i am not at work but on a different site ?I tryed almost anything but the application still looks directly on my local ip instead of the ip of my vpn
I've been searching high and low for a "blank" stencil to fill in module and WIC areas of a 2821 router that I'm diagraming. Where I can get a hold of something that will work? It seems that Cisco is somewhat lax lately on their visio stencil offerings.
I need to make some perfomances (like up/down GRE tunnels) on Cisco ISR 2921 by sending SMS. It could be doing by using 3G modem like a Huawei and a server with some expect/SSH-scripts.
But ISR gen.2 has EHWIC-3G modules, which working with GSM networks and they can send/recieve SMS. I think, that it should be an EEM event or some another way to track comming SMS and process it by TCL-script — get a sender number, SMS body and make usefull perfomances on my router (up/down GRE tunnels in my case).
If I done this trick only by using an ISR router and EHWIC-3G module, it will be much more stable scheme in that we dont have extra components (server, modem) potentially may falls.
Unfortunately, there are too low information about configuring this modules (especially, SMS-part) and I dont find usefull for me.
I have many HWIC-3G-HSPA cards as backup connections and I need to keep them up for monitoring purposes. Being a backup connection they get little interesting traffic for them to spring into life but they are the source interface for a tunnel interface (we use DMVPN). The interface still insists on going down. I have even added static routes to the DMVPN hubs over the cellular interface and they still go down. What command do I enter to always keep them up? I had originally used 'dialer idle-timeout 0' and then removed it altogether which the same results. Below is what I have now.
interface Cellular0/1/0 ip address negotiated ip nat outside ip virtual-reassembly in encapsulation ppp dialer in-band dialer string gsmscript dialer-group 1 async mode interactive ppp chap hostname //username// ppp chap password //password// ppp ipcp dns request
access-list 1 permit anydialer-list 1 protocol ip list 1
line 0/1/0 exec-timeout 0 0 script dialer gsmscript modem InOut no exec transport input all transport output all rxspeed 7200000 txspeed 5760000
I've recently changed my DSL connection to HSPA because of low speed of DSL connection (2000).
Anyway, I need to build up 5 Ghz networking at home but there is no dual band HSPA modem router on the market. I need a router which supports DLNA/UPnP for NAS Server. So, I have couple of solutions...
1- I can purchase dual-band Asus RT-N66U and use HSPA/UMTS stick to use this router as main router. I can do this because RT-N66U supports sticks via USB.
2- I can connect my HSPA modem to a dual-band router via LAN and by changing IP adresses I can use dual-band router again as a main modem router. This can be no problem via WAN but my modem has no WAN connection. Is this possible via LAN?
Or do you have any other solution how I can get my 5 Ghz netwroking at home using HSPA connection.
I am having problems with these types of 3G cards(EHWIC-3G-HSPA+7) from Cisco.We are using them on ships where we have a SAT connection and the 3G connection. Fail over between the two connections are handled by an IP SLA echo and a track on the cellular interface, towards an public IP where we have configured a static route to via the Cellular interface.
Once configured the connection comes up fine, the VPN tunnels comes up and all is good.But after some time the connection dies, the track goes down because no data goes through.a sh cell 0/0/0 all however say that the profile is active.
i have a dell mini 10 that had ubuntu but i put vista on it and after i did it my network controller wont install and i downloaded almost every driver dell had and one worked but i had the 39 error code, the driver that worked was DELL_WIRELESS-5530-HSPA-MINI_A06_R220877 but had 39 error code
I am thinking about buying Dell 5550 module to my Latitude E6410. I know that for E6410 is designed 5540 module, but newer 5550 for E6420 has ability to use faster HSPA+ networks.
So my question is, any info on this combination of Latitude E6410 and Dell 5550 module?
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
I haven't been able to find any Windows 7 compatible drivers anywhere for the CB21AG card and there seems to be nothing on the Cisco site. These drivers required, when they might be released?
i recently reinstalled windows XP pro onto an msi ms-1012 laptop and after that i couldn't get internet by Wireless. and i started to install the required drivers and i could not find the wifi driver!(it has an integrated wireless 800 .11 b/g or sth like that)also, on device manager it has a missing icon (the big yellow ?) on the following devices:
PCI Modem; Network adapter
so i need to determinate, what exact wifi hardware i have, to download proper drivers.[URL]
My windows xp wireless drivers was functioning normally in my dell610.but accidentally i uninstalled it, now i am trying to install it but it ends up with an icon at the bottom which shows that it is installing but nothing is going on.i have tried this several time but i failed.
My computer crashed the other day and HDD failed. i finally got it back up and running but ive been using a usb wireless adapter. i do not have the disk anymore to install the drivers, nor will my computer install them from the internet because i dont have an internet connection on my desktop. what are my options to have them installed?