Cisco :: Searching With Question Mark

Oct 2, 2012

Is there any way to do,i on the help menus (what you get when you put in "?")?

View 3 Replies


ADVERTISEMENT

Searching For Available Wireless Networks

Jan 26, 2011

I've just reformatted my computer and reinstalled windows xp but i can no longer find the window where you search for available wireless networks. It used to be a little icon in the bottom right of the task-bar.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 Multiple Domain Prefix Searching?

May 23, 2011

We have an ACS 5.2 server connected to an AD domain controller which has several trusted domains.  (domain1, domain2, domain3)  We currently have to specify which domain each user belongs to (ie, domain1user) in order to connect.  We would like to only have to enter the user name without the prefix, (ie, user1) and have ACS automatically check each domain for a match.  Is this possible with ACS 5.2?  I seem to remember this was possible with ACS 4.2.

View 2 Replies View Related

Cisco Wireless :: PCEX-3G-HSPA Searching For Drivers

Oct 11, 2011

I have found in my storage a device: PCEX-3G-HSPA (attached a photo of it)

And wanted to use it, but cant find any drivers for it. My OS is Windows 7 64bit. How to make this device to work under Win 7?

View 1 Replies View Related

Application Searching Access On Wrong IP Address?

Nov 2, 2011

I have an application for work that I need to access true vpn connection :I have Sbs server 2008 with vpn support , I can access my folders and exchange and ... , this works fine.Now I have an application that search to connect to the server via local ip at work but when I use vpn to access it then the application goes searching on my local ip adress and not on the vpn ip adress.vpn has same ip as local ip at work).Now my question is: Can I set the application to search on the range of my vpn connection instead of searching on my local ip when i am not at work but on a different site ?I tryed almost anything but the application still looks directly on my local ip instead of the ip of my vpn

View 8 Replies View Related

Cisco WAN :: 2821 Searching High And Low For Blank Stencil To Fill In Module

Apr 25, 2010

I've been searching high and low for a "blank" stencil to fill in module and WIC areas of a 2821 router that I'm diagraming. Where I can get a hold of something that will work?  It seems that Cisco is somewhat lax lately on their visio stencil offerings.

View 6 Replies View Related

Mark Traffic Coming From S1 To R1 - S2 To R2 - And S3 To R3 On Switch 2

Mar 25, 2013

I have a small problem and I'm a bit confused, Cisco suggested that you should mark traffic as close to the end devices as possible. So I wanted to try marking the traffic coming from S1 to R1, S2 to R2, and S3 to R3 on Switch 2 (Cisco Catalyst 2960) with the following config:

[code]...

View 9 Replies View Related

Yellow Mark In Device Manager

Feb 18, 2011

Next to network adaptors there are yellow marks in my device manager...as follows.

-??(yellow mark) Other devices
-??? (yellow mark) Unknown device
-??? (Yellow mark) Unknown device

View 1 Replies View Related

Yellow Mark Over Network Icon?

Apr 2, 2012

I am using a Sony Vaio with the following Configurations Win 7 Professional 64 Bit SP 1 The Wireless adapter is Intel Centrino N 6230 with the drivers updated The LAN adapter is Realtek PCIe GBE Family Controller

This laptop is pretty new and I had been experiencing some problems with Wifi and LAN connectivity to internet.

Initially there was a yellow mark over network icon but it allowed me to access Internet. I was not bothered then..Offlate this has turned ugly. The yellow icon would not allow me to connect to internet through wifi or LAN

Sometimes LAN would connect but now a days connecting to wifi has become a real task with most of the time having to trouble shoot the connection.

Troubleshooting gives me different suggestions which are as follows

a) DHCP not enabled over wireless networks....Trying to repair the same does not work

b) Your computer seems to have been configured properly.

c) Troubleshooting cannot solve the problem

I cannot connect to wifi in office and home. I had mcafee before but removed it completely using mcafee removal tool..

View 13 Replies View Related

Cisco WAN :: ASR903 - Mark BFD Control Packets In Routers?

Dec 18, 2012

Is there a way to mark BFD control packets in Cisco routers (such as ASR903) with high priority, so it gets treated with priority in swithcing network between two routers, in turn not suffers from packet loss and delay   ? 

View 3 Replies View Related

Cannot Connect SSID - Yellow Mark With Limited Connection

Jan 15, 2012

i'm using win7 and linux mint in my laptop. when i'm on linux i 'm able to connect in a specific ssid with my b43 driver. when i switch back to windows(broadcom a/b/g) i can not connect to this ssid-there is a yellow mark with limited connection. what do you think? is this a driver problem with win7. or win 7 driver has ''less power'' than linux's?

View 2 Replies View Related

IP Address Displays A Question Mark On The Command Prompt

Mar 15, 2011

When I went to the cmd prompt and typed in ipconfig/all I got...

Ethernet adapeter Wireless Newtork Connection 4:
Description- Dell Wireless Mini Card
Physical Address-00-1E-4C-05-99-B3

[Code].....

View 1 Replies View Related

Security / Firewalls :: Getting Yellow Triangle With An Exclamation Mark?

Nov 27, 2011

I tried to plug in the internet cable in my laptop i kept getting that yellow triangle with an exclamation mark on it (down in the right). i kept plug in and out the cable until i got connected. i use a cable/dsl router, having 2 computers connected in the same time. only mine gave this error, as the other ran perfectly in the meantime. what seems to be the problem? a virus/trojan?

View 1 Replies View Related

Yellow Question Mark Showing On Ethernet Controller

Nov 26, 2012

I am showing a yellow question mark on my Ethernet controller.

View 1 Replies View Related

D-Link DIR-655 :: Unknown With Question Mark On Map Between Wired PC And Router?

Jan 23, 2012

when using Windows 7 network map, there is a "Unknown" with a question mark on the map between my wired pc and the router.

View 10 Replies View Related

Cisco Switching/Routing :: 3750 Cannot Mark Http Traffic With DSCP

Mar 14, 2012

I am trying to mark http packets from a web server with DSCP ef, but when I am doing a traffic capture all http packets have tos 0x0.I am able to mark UDP and ICMP packets originated from this server, but not any TCP traffic.The web server is in VLAN 20This is my config mls qos ip access-list extended MARK-HTTP-ACL  permit tcp host 10.10.10.10 eq www. [code]

View 4 Replies View Related

Yellow Question Mark In Device Manager Ethernet Adapter

May 16, 2012

I have windows xp with asus motherboard p5kpl-am se. my issue is that I cannot get on the net. I know there is internet connection, but the computor won't recognise that fact. when I go to repair the internet connection, I get a message ( windows cannot detect any wired or wireless cards on your machine) things I have done is to download drivers for the ethernet card and also the motherboard chipset to see if that would work, but no change. the yellow question mark is still there.

View 4 Replies View Related

Protocols / Routing :: Network Connections Icon Have A Exclamation Mark?

May 29, 2012

my computer, my network connections icon have a exclamation mark (!) and it say i don't have internet access,but luckily i have internet access but i can't remote my computer,

View 4 Replies View Related

Laptops Wireless Signal Showing Yellow Mark No Internet?

Jan 30, 2013

in some laptops wireless signal showing yellow mark no internet, but we are getting internet

View 1 Replies View Related

Sitecom Gigabit 300N - Yellow Exclamation Mark On Connection?

Feb 3, 2013

my router is sitecom gigabit 300N. since the past week there is this yellow exclamation mark on the connection in the task bar, near the clock. if I pass the mouse over it, it says no internet connection, eventhough I'm connected to the internet and I'm writing this right now, this is on desktop pc and connected to router by cable. the same thing on my laptop that is connected through WiFi, the signal strenght is normal, but there is the same exclamation mark. I'm pretty sure its the router not the PC because this happens on two different machines with the same router. I tried turning the router off and left it that way for about 7 minutes but that didnt work. is there something in settings I should do? or throw it away and buy Linksys/D-link router?

View 6 Replies View Related

Linksys Wireless Router :: E1200 When Run Cisco Connect After Couple Minutes Searching / Can't Find Router

Mar 9, 2012

I want to use cisco connect with the Router E1200. There is a wireless connection between laptop and E1200 Router. When I run the "Cisco Connect" after couple minutes searching It can not find the Router and I have to put an (Router name SSID) and password.

View 9 Replies View Related

D-Link DCS-942L :: Searching Support Website Getting No Link

Jan 30, 2012

I have 1.00 build 0522 and searching the support website I see no link.  But reading here I see there is a later version.

View 1 Replies View Related

Cisco :: Test Fast Roaming Using A Cisco 2100 Series Controller And 2 1140 APs?

Jul 20, 2011

I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.

View 1 Replies View Related

Cisco WAN :: Does Cisco Catalyst 2960-8TC Support Bandwidth Limit Control

Aug 22, 2011

We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.

View 1 Replies View Related

Cisco Wireless :: WLAN Cisco / AP 3502e - How To Get PAT (Product Acceptance Test)

Dec 3, 2011

I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.

View 0 Replies View Related

Cisco Firewall :: Cisco ASA5510 Unable To Block Unwanted URLs

Jul 12, 2012

I have  cisco ASA5510 firewall  using in my network but  unable to bolck Url's  unwanted. can i block the [URL] on the asa by using regular exp.

View 3 Replies View Related

Cisco Switching/Routing :: Configuring COS On 2960G Switches With Non-Cisco Phones

Mar 1, 2012

I have 7 POE switches that have ESI IP phones attached.  I have two VLANS, 1 and 2.  VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
 
I have had voice quality issue between floors in my building.  Talking to others on my floor via the IP phone, there are no voice quality issues. [code]

View 1 Replies View Related

Cisco Wireless :: Connect Ap-1242AG With Non-cisco Router To Work As Repeater?

Nov 18, 2012

is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?

View 1 Replies View Related

Cisco :: Unable To Understand Cisco Syntax For Nat Rules On 5550

May 1, 2012

I am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.

View 8 Replies View Related

Cisco :: IPSec Tunnel Between Cisco ASA And OpenBSD (Access Enforcer)?

Mar 10, 2011

I currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.

View 3 Replies View Related

Cisco Switching/Routing :: Cisco 3750G Error During POST

Dec 5, 2011

I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
 
% Error: Unable to create flash:/microcode_update% Error: It must not already exist

Normally, getting an error during POST isnt a good thing.  My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change.  I next tried fsck /test flash:.   It tested 77 blocks and performed 0 erasures.  It had been running for about 15 minutes with no problems reported so far.  Multiple reboots of the switch still report the same error.
 
I have reviewed the history of what I have done on this switch and finally think I found the problem.  I noticed a microcode_update directory that I am not used to see on a 3750.  Deleted the directory using the rmdir command and rebooted the switch.  On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created.  The switch now boots up without any errors.

View 3 Replies View Related

Cisco Wireless :: 2 Cisco Aironet 1401 APs Keep Kicking Users Off

Jan 3, 2013

I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
 
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.

View 17 Replies View Related

Cisco :: CISCO Advanced Firewall On 2911 Router Using CCP?

Dec 29, 2012

Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.

View 19 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved