I haven't been able to find any Windows 7 compatible drivers anywhere for the CB21AG card and there seems to be nothing on the Cisco site. These drivers required, when they might be released?
View 11 RepliesI need to update from older Cisco 350 Aironet 802.11a/b Wireless CardBus Adapters to Cisco cb21ag Aironet 802.11a/b/g Wireless CardBus Adapters in rugged tablet pc's. I need these without the antenna cap present to utilize the tablets antenna sytem. They are pictured on the Cisco website but Cisco partners I've contacted have been unable to assist me in purchasing them.
View 1 Replies View RelatedI'm having a small issue using my external CIsco Wireless Card AIR-CB21-AG-E-K9 with a Lightweight Access Point 1552 (Outdoor) using 802.11a Radio.
Description of issue :
I can connect to a wireless network when i set the Wireless Mode to 2.4GHz 54 Mbps (802.11 g), and 2.4 GHz 11 Mbps (802.11 b) on the card but not with 5GHz 54 Mbps (802.11a).
Note that this card is compatible to 802.11 a, b and g.
All settings on the 2504 WLC is set to default regarding the radios configuration.
Both radio interfaces type (802.11 b/g/n and 802.11a/n) are operational and Admin status Enable on the WLC.
The status of the wireless card is as follows :
Profile Name - Wifi-Test
Link Status - Not associated
Wirless Mode : 5 GHz 54 Mbps
Network Type : Infrastructure
Current Channel : Scanning
I am able to view clients, rogue APs, rogue clients etc, but the information is faily inaccurate. Thus, I am trying to calibrate using the RF calibration models. I have created a new model and am attempting to add data points.After adding the client MAC, selecting the floor plan and clicking next, the floor plan loads and a message pops up stating: "Could not enable S60 across all relevant controllers on this floor". I click OK, and select "point" as the calibration method. When I place the calibration point on the map and click GO I am presented with the following message: "Failed to initiate data collection. Please make sure your client is connected on the wireless network and then try again." Both of these messages can be seen in the attached screenshots.
I have confirmed that the client is associated to an AP located on the map.I have confirmed connectivity of the client.I have used both the Cisco AIR-CB21AG-W-K9 (CCX V5) and the integrated intel wireless card (CCX V4).I am running WCS 7.0.172.0, MSE 7.0.201.204, and WLC 7.0.116.0.
I need drivers for AIR-PL21AG-A-K9 wireless PCI card which works on windows 7.
View 1 Replies View RelatedMy windows xp wireless drivers was functioning normally in my dell610.but accidentally i uninstalled it, now i am trying to install it but it ends up with an icon at the bottom which shows that it is installing but nothing is going on.i have tried this several time but i failed.
View 1 Replies View RelatedWindows 7 was delted form my laptop as i didnt have a windows 7 disc to re-install it, i had to install windows xp.XP runs fine but i cant connect to the internet, ive been on the acer site downloaded all the wireless drivers and still nothing.
View 4 Replies View RelatedMy internet has stopped working after windows7 installation. Wireless icon is missing after windows7 installation.
View 1 Replies View RelatedI had Ubuntu and have reformatted and installed windows 7. Did not think about having wireless driver compatibility issues. My driver is a Marvell 88w8335 [Libertas] 802.11b/g wireless. Are drivers for this available for win7 or do I have to buy new?
View 3 Replies View RelatedI am having problems installing this with the cd that was given, so I went on the site to DL the drivers, i downloaded the zip file, but when i open it there is no setup.exe. Do i need to exract the contents to a certain file?
View 1 Replies View RelatedIs there a driver or will there be a driver to work with WUSB300n adapter running Windows 7 64-bit Home Pro edition ?
View 1 Replies View RelatedI am looking for WRT54G v7 Windows 7 Drivers. I can seem to find it. If there is no update yet, need drivers for Windows Vista 32 instead.
View 9 Replies View RelatedSo I have a (relatively) old WMP54GX PCI adapter that used to work great under XP. However I moved and was able to put my computer right next to my router so I no longer needed to use the adapter. Fast forward about three years later, I now have Windows 7 installed and need to use to adapter again, but unfortunately it doesn't seem to be working. The drivers never seem to finish installing after reboot, and I'm not sure what I should be doing. I noticed the most "recent" driver was released in 2006, so it doesn't look like there's even one available for Vista, let alone Windows 7.
Am I looking in the wrong place for the drivers, or is Linksys really not supporting their slightly older hardware on new operating systems? If there are no drivers available, any ways to get it working in Windows 7?
I recently formatted my XPS M1530 and installed Windows 7 32-bit Ultimate on it. Everything works flawless, except for the wireless. I have tired installing the Vista drivers available on the Dell website but it did not work. I have tired several other drivers (compatible with my product) also, but they too dint work. Infact, my bluetooth doesnt even work.
View 9 Replies View RelatedI recently updated to Windows 8, and before updating, Windows 8 setup recognized the drivers for my Belkin G Desktop wireless card. After installation, my system was able to connect to my wi-fi network without any problem. However, due to the power going off at my home, an automatic update on Windows 8 got interrupted.
Since then, it has caused a ton of problems, which caused me to finally re-install Windows 8. Now, however, it does not recognize the wireless card and its drivers, and does not let me install from the CD, or through any alternate sources ?
Started a fresh installation on windows 7 RC 64 bit popped in adapter, and tried installing disk, disk would get the portion where it asked to input the adapter, then just vanish after i click next. I restarted, nothing. I clicked set up again, says drivers are already installed....though there is no app to show profiles, im guessing it isn't.
[URL]
version 1.00 would work just like the disk. version 2.00 would not start at all and would give an "the application was unable to start correctly (0x0000005).."
I have a Dell Latitude D610 ,and i can't find drivers for Windows 7.
View 7 Replies View Relatedwho had a WMP300N with the Broadcom 4329 chip (PCIVEN_14E4&DEV_4329&SUBSYS_00601737&REV_01)Since i got my WMP300N all that i got is a really a big headache, since the drivers DOESN'T are meant for Win 7 (x86/x64), and the guys at Cisco/Linksys really are so kind to bring an unstable driver (v6.100) that they claim is for win 7.
i, as same as a ton of users, really get dissapointed because the driver in the cd does not work on win 7 and the 'official updated driver' is useless as well, and in the end lost a lot of time searching almost in the entire internet for a solution, that some pages claim to have, but the info is oudated, or the links are gone.so in a insurmountable-almost-titanic search, i somehow managed to gather all the required files that i'll put at disposition of those like me have a bad time with a supposed to be a pretty good wireless card.
1- bmc 4329 v4.100, this one is the most 'stable' and works pretty well in 32/64bits, it had a modded .inf wich enables a few features that various users will find pretty useful, when the installer prompts a warning about an unsigned driver, you had to allow the installation
2- bmc 4329 5.100, this one is working too on 32/64 bits, i'm posting it because some people got problems with the 4.100 version, however, the 5.100 is a stock unmodded driver, so maybe it will give connection issues.
I cant install drivers for Windovs XP both 32-64 Professional. Original CD tells me for x64 OS is not supported, also, when trying to install only drivers it just can't find it. For x32 same problem - can't install drivers. I've got Intel DP45SG.
View 5 Replies View RelatedI just bought a WMP600N adaptor and although windows 7 recognizes it I would like to install the official drivers from Linksys. When I try to update the drivers that I downloaded from the linksys website I het an access denied error. I am logged in as the administrator. I have already tried uninstalling the default drivers, but still I get the access denied error. I even tried the windows safe mode and still got the access denied error.
With the default windows 7 drivers the connection is quite poor. how I can install the official windows 7 drivers?
Need drivers of Nokia bh-106 for windows 7 ,when i am trying to connect the wireless head set to my laptop the message reads as no drivers found
View 2 Replies View RelatedI neeed network drivers for an HP desktop PC
View 1 Replies View RelatedI need universal lan driver for windows 7
View 3 Replies View RelatedHp 630 drivers for windows 7 32 bit free download
View 1 Replies View RelatedWhich driver i need for net?
View 2 Replies View RelatedI had a Windows 7 automatic update last night. Went through the process and when it was done, everything was working fine. I did a proper shut down and went to bed. Woke up this morning, turned on my laptop and now I have NO network drivers. Tried a system restore prior to the "critical updates" and that didn't work either. So what the.
View 3 Replies View Relatedi want drivers for Toshiba satellite L700 windows 7 32 bit
View 1 Replies View RelatedWindows7 drivers for Toshiba satellite c655?
View 1 Replies View RelatedI am trying to use this belkin surf n150 in a Netbook thats is running Windows CE embedded 6drivers for windows ce6 and can not find any drivers
View 1 Replies View RelatedAny way of getting drivers for aDWL-G120 drivers to work on vista?
View 1 Replies View Relatedhow can i download video and audio drivers for lenovo thinkcentre mt-m 9482-cc3. i have search since 2 two days and i couldn't fine them.
View 2 Replies View RelatedWindows 8 just released not long ago, and I am eager to upgrade my laptop to this version. From what I am understanding that Bluetooth is an issue along with Dell own drivers and configuration caused the upgrade delay. Dell will resolve and make drivers available to Windows 8.
View 1 Replies View RelatedWhere can I go and download free software for 802.11n technology for RTL8188CE drive/adapter 802.11 b/g/n? I need the full power of the n technology since the n technology in the adapter I have was in its preliminary developmental stages. I have a mini pc and operate with Windows 7.
View 1 Replies View Related