I understand that the PCEX-3G-HSPA requires and a sim card. I also have a PCEX-3G-CDMA-V. Does this require a sim card as well? And if so, where is the sim card installed?
View 1 RepliesI am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies View RelatedI have a new 8881G-w router with the following info:
(C880DATA-UNIVERSALK9-M), Version 12.4(22)YB2, Serial No. FTX1331830T
Need activating the CDMA . when I tried to login to the Cellular interface it shows me the following warning:Warning: 3G Modem is not inserted Configuration will not be effective until modem is inserted
I want to activate and configure CDMA and i don`t know from to start..
If I setup 4948E's in HSRP configuration. And I connect devices to the Standby Unit that do not require redundancy. Will there be any issues passing traffic? I don't believe that standby unit blocks the traffic but wanted to confirm.
View 5 Replies View RelatedI am doing my college project(Client Server Chat Application in C#). I need to transfer all the data of my application through a VPN tunnel. I want to create a IPSEC VPN tunnel through which I can route the Data. I am low On budget I am not inclined towards buying any Hardware. So is it necessary to purchase a Router or a Network Interface Card To create A IpSec VPN.
View 3 Replies View RelatedI have found in my storage a device: PCEX-3G-HSPA (attached a photo of it)
And wanted to use it, but cant find any drivers for it. My OS is Windows 7 64bit. How to make this device to work under Win 7?
I have an interesting problem. I've configured a site to site VPN connection between these two devices. I am using the CDMA card as the primary and only outside connection on the 1921. What happens is that by default the cellular connection is offline. When traffic is generated internally from that network to the concentrator side of this scenario the cellular connection goes online and builds the tunnel, no problem. However, I cannot initiate the tunnel from the concentrator side. I think what i need is a way to force the cellular connection to always be on, and if it fails to come back online.
View 3 Replies View RelatedThe problem is I can't access the router from the internet. I am also an ocean away from the site. I have an ugly hack set up where I access an inside PC with Teamviewer and then puTTy to the router, but it is slow, ugly, and doesn't fix my problem. I need to be able to set up internet accessible servers at this location for VOIP, VPN, and REAL remote access.Everything else works fine. Connection is stable. Speed is kinda ******, but that's not so important.
First off some specs:Cisco 2801c2801-ipvoicek9-mz.124-24.T1.binhwic-3g-cdma-sSprint 3G data plan
Ok, I have set up the previous equipment as a router for a branch office where 3G access is the only available internet access.I have had the excruciating experience of talking with Sprint Tech Support, and would rather shoot myself in the foot than do so again.
Here is what they told me: "They block ports, but they can't tell me which ones."Here is relevant info I have been able to gather.The IP connection the ISP gives us is not NATTED. That is the address at wimi.com and show int dialer 0 is the same one.Most forums say Sprint only blocks port 80.Zenmap (nmap for windows) says the router has NO open ports but DOES exist.Router does not respond to pingsCan't SSH into router from internetCan't access a test local server with port 8080 or 8081 open with the correct nat statement in Cisco routerNo filtering access-list for testing The config should be just fine as a base config for using hwic-3g-cdma-s as the main internet access interface for a router. Everything works fine aside from the lack of remote access.
So in my head it has to be one of 3 problems.
1. The card is doing some weird stuff to incoming requests
2. Sprint is blocking WAN requests on port 22, 2200, 8080, and 8081 and pings (tested). Maybe they block all WAN requests?
3. There is something wrong with my config.
why I can't remote access into my router or things to try with the config?
Below are some config pastes:
chat-script cdma "" "ATDT#777" TIMEOUT 60 "CONNECT"
!
ip ssh authentication-retries 2
ip ssh port 2200 rotary 1
ip ssh version 2
[code]....
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedI have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies View RelatedI have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedI have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies View Relatedi have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedI have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replies View RelatedI am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View RelatedI can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies View RelatedI will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies View Relatedwhen replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies View RelatedNeed to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedWhich WIC or NM Ethernet card is compatible with a 2620, (non XM) router? I have seen conflicting information on compatibility. I am wanting to connect this router via an Ethernet Port with a non Cisco router that is connected to my ISP.
View 1 Replies View RelatedI've Cat. 6509 with minfail status of DF card.There is no any errors in log and diag logs.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1229XU2B
2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BZ
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6CD
4 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BS
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1228WPEB
[code].....
I have just buy a 10G card for Cat 6513, these are information: PDCMSFC-1>sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL08373Z37
7 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD08330322
Mod Sub-Module Model Serial Hw Status
--- --------------------------- ------------------ ------------ ------- -------
7 Policy Feature Card 3 WS-F6K-PFC3A SAD083207AL 2.4 Ok
7 MSFC3 Daughterboard WS-SUP720 SAD0832037Y 2.3 Ok
About card: WS-X6716-10G-3C
When I install this card on Cat 6513, has a message: " fan tray no support"
I just received a Nexus 5548 to configure as the core of the Datacenter LAN. Is it true that the VRFs created cannot talk to each other??? I can't seem to find any documentation on how to do this and at least one TAC engineer half-heartedly believes it's not possible, either.
Basically, I'm trying to get an SVI in VRF1 to be able to talk to an device on another SVI in VRF2.
I can't believe this high-end switch, that is so capable in every regard, cannot handle this feature.
Can i use this card (WS-X4612-SFP-E) in chassis 4503E with Supervisor WS-X4013+TS ?
View 1 Replies View RelatedProblem I have encountered when upgrading a Cisco 6509 chassis with a new supervisor card from Sup2 to Sup 720b. The 6509 loads and then crashes completely, and when rebooted reloads into rommon.The same upgrade was performed on a similar switch with no apparent problems.
[code]....