Cisco Switching/Routing :: 4503E - Using Card (WS-X4612-SFP-E) With Supervisor WS-X4013+TS
Feb 13, 2012Can i use this card (WS-X4612-SFP-E) in chassis 4503E with Supervisor WS-X4013+TS ?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 6509 Crash When Upgrading Supervisor Card
Nov 23, 2011Problem I have encountered when upgrading a Cisco 6509 chassis with a new supervisor card from Sup2 to Sup 720b. The 6509 loads and then crashes completely, and when rebooted reloads into rommon.The same upgrade was performed on a similar switch with no apparent problems.
[code]....
Cisco :: WS-x4612-SFP-E Card Supported In CiscoView?
Sep 8, 2011I would like to know if WS-x4612-SFP-E card is support in ciscoview ? If not, when it will be support ?
View 4 Replies View RelatedCisco Switching/Routing :: WS-X4516-10GE Works With WS-X4612-SFP-E?
Dec 4, 2011Is it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies View RelatedCisco Switching/Routing :: 4503E With Sup 7-E And IOSX 3.2 / Enable Routing?
Apr 3, 2013Have a 3750X running at the moment and has about 30 vlans all connected and just use the ip route global config command to enable routing. Plan is to switch out to the 4503E, with IPBase license. When ever I issue the same command, and do a show run its not there. I get no error when I issue the command either. And yes I have rebooted. Do I need to use RIP or OSPF routing? When I do a show ip route the screen looks the same with all the codes, though gateway of last resort isn't set even though I do have ip route 0.0.0.0 0.0.0.0 a.b.c.d in the config. Or is ip routing just enabled by default?
View 6 Replies View RelatedCisco Switching/Routing :: 4503E Universal Crypto Image?
Apr 25, 2013find what feature set is supported on this IOS S45EUK9-33-1511SG The client requires Layer 3 functionality so do i need to apply any license with it or it will perform layer 3 routing (like rip, ospf, bgp, ipv6, ospfv3) ?
View 1 Replies View RelatedCisco Switching/Routing :: Upgrade Software Of Core Switch 4503e?
Nov 2, 2011i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?
Cisco Switching/Routing :: 4503E Share Bandwidth Between Traffic Classes With Percent Up To 1 Mega
Jul 16, 2012I have one Catalyst 4503 with Supervisor 7L-E 10 with IOS - XE 03.02.00.XO. . One of its gigabit interfaces is connected to a Internet link of 1 Mega. In terms of QoS i would like to limit the total bandwidht of this gigabit interface to just one 1 Mega and simultaneous i want share bandwidth between traffic classes with bandwith percent up to 1 Mega and not 1Giga.
View 1 Replies View RelatedCisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy
Jan 11, 2012we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedDistributed Forwarding Card For Supervisor Engine 2T
Dec 23, 2011I was looking to 6500 series switches. I saw DFC4 module (WS-F6K-DFC4-A, WS-F6K-DFC4-AXL) and (WS-F6K-DFC4-E, WS-F6K-DFC4-EXL). Data sheet for supervisor engine 2T wrote that for maximum performance you should DFC4. I'm a bit confused. I didn't any useful information about it:
1. DFC4 is a separate module(consumes 1 slot)? Does it have any ports on it?
2. Is it a daughter card? If yes, should it be installed on supervisor or it should be installed on line cards?
Cisco Switching/Routing :: Supervisor Engine 720 Errors
Apr 18, 2013i have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedCisco Switching/Routing :: 6500 What Happens When A Supervisor Fails
Feb 3, 2010We've been mocking up a test lab to test VSS on two 6500's. Each 6500 has one sup720 and a 6708-10ge blade and we've established the two 10ge links between the two chassis; the first from the each chassis' sup and the second from each 6708.My question is, what happens when the supervisor fails on one of the chassis?
View 10 Replies View RelatedCisco Switching/Routing :: Supervisor 7-E / 7L-E Port Numbering
Jan 30, 2013How the port numbering would be on Sup 7-E and Sup 7L-E? I mean, on Sup-6E and Sup-6LE, if I used a twin-gig converter, I used ports gi3/3,gi3/4,gi3/5 and Gi3/6 [If the sup is in 3rd Slot]. I know there are now 4 ports on the Sup 7 which can either be used as Gig ports or TenGig ports. So, how will the port numbering change ?
View 1 Replies View RelatedCisco Switching/Routing :: Supervisor 7L-E USB Port Is Not Working?
May 1, 2012Nothing happens when we plug a USB Flash Drive into an SUP7L-E USB port.
View 4 Replies View RelatedCisco Switching/Routing :: Upgrading Supervisor In Cat 4500?
Feb 20, 2012I have a 4510R-E chassis which currently has a single supervisor 5 installed.
We are now looking at upgrading the supervisor to a Sup6. Now the question is this, can I install the Sup6 into the redundant cpu slot and then perform a failover to get the new switch working without any noticable downtime.
I'm not sure what having a Sup V and a Sup 6 in at the same time will do to the backplane.
Otherwise I have to take the switch down and then install the card and software manually.
Cisco Switching/Routing :: VSS With 4 Supervisor Engine 2T-10GE
May 6, 2013We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
Cisco Switching/Routing :: Catalyst 6500 / QoS For Supervisor 2T?
Apr 30, 2013I need to configure QoS (voice and video) for Catalyst 6500 series switches with Supervisor 2T modules and DFC4 linecards.
Is this radically different from what we do int he Sup32 and 720s? I was looking at some templates online, such as
[URL]
But I don't see anything for the new Supervisor 2T?
Cisco Switching/Routing :: Cat 4500 Supervisor 7-E Is Rebooting
Apr 24, 2013I'm having a trouble with a 4510R+E switch. The WS-X45-SUP7-E supervisors are constantly rebooting, and we can see a 'critical software exception reload' reason. We have checked the logs
______ uptime is 5 weeks, 1 day, 19 hours, 3 minutes
Uptime for this control processor is 37 minutes
System returned to ROM by reload
[Code]....
What can we do to solve this incident?. Everything was working fine, and suddently the problem arose.
Cisco Switching/Routing :: QoS Catalyst 4500 7E Supervisor
Apr 15, 2012I am trying to understand the implicit limit to the priority queue. I know you can define an explicit policer but if you don't I can't find out what the rate limit really is.
View 5 Replies View RelatedCisco Switching/Routing :: Catalyst 4510R+E Supervisor 7-E SSO Not Available
Sep 22, 2011I'm working on deploying a new 4510R+E for our organization. This is my first experience with a modular switch. I'm trying to enable SSO, however in the redundancy configuration mode, the sso command is not available. Is SSO only available with certain software images / licensing levels? [code]
View 2 Replies View RelatedCisco Switching/Routing :: 6509 Supervisor IOS Upgrade
Oct 16, 2012We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3
Cisco Switching/Routing :: Catalyst Supervisor 32 NVRAM Location?
Feb 10, 2013I have a Sup32 that I suspect has faulty NVRAM (e.g., I am unable to "wr mem" on the device - it states resource is busy but no other active connections exist). Prior to replacing the supervisor engine I'd like to take a crack at formatting NVRAM to see if it resolves the issue. This supervisor does not have a CF card installed, thus no Disk0:. Within the CLI, I am presented two options with the "format" command - bootflash: and sup-bootflash:. Bootflash: does not have any data on it, however, sup-bootflash: contains my IOS image. I believe that both of these locations are simply directories within NVRAM.
View 3 Replies View RelatedCisco Switching/Routing :: 6509 How To Configure VSS With Two Different Supervisor Engine
Oct 1, 2012I have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies View RelatedCisco Switching/Routing :: Upgrading Supervisor Engine On 4006?
Nov 3, 2011I have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
Cisco Switching/Routing :: 6509 Adding A Redundant Supervisor?
Feb 10, 2012I would like to add a redundant supervisor to my core 6509. Is this tricky to do? I know they have to be running the same IOS. I am worried if I put the new supervisor in it will write over the exsisting running config.
Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2
Policy Feature Card 2 WS-F6K-PFC2
Cat6k MSFC 2 daughterboard WS-F6K-MSFC2
Cisco Switching/Routing :: Catalyst 4006 Supervisor Engine Led Red
Nov 28, 2011we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedCisco Switching/Routing :: 6509 Supervisor Upgrade With FWSM?
Oct 8, 2012We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
Cisco Switching/Routing :: Catalyst 6500 Dual-Supervisor 720-10G-3C?
Sep 21, 20121. We now have SupA & SupB in the chassis, due to some mistake we have same IOS version but different feature set on them, although we configured redundancy mode sso, in the "show redundancy" we see Operating Redundancy Mode = rpr due to Software mismat, we now need to fix them as same feature set image, if I use "copy sup-bootdisk0:/xxxx slavesup-bootdisk0:/xxx", then write memory, does this cause any service/network interuption?
Available system uptime = 1 year, 1 week, 4 days, 9 hours, 21 minutes
Switchovers system experienced = 2
Standby failures = 0
Last switchover reason = active unit removed
[code]....
2. We did a failover test with this status, found that if we triggered supervisor failover, all modules will reload thus the services if interupped. How about after we make the Operating Redundancy Mode as sso, will this behaviour shows again? Or a stateful failover will happens, then modules no need reload?
3. We are using OSPF as our L3 routing protocol, after reference to the configuration, nsf should be enabled, we want to ask in the OSPF-domain nsf should be configured in all OSPF-enabled router or only 6500 which have dual-sup?
4. We also found that the interfaces(3 * Gig & 2 * TenG) in Standby supervisor cannot be use even enabled & configured, is it because we are running rpr mode now or will be the same even change to sso? Before customer have some older supervisor in 6500 non-e chassis, and they can use the standby supervisor interfaces as traffic forwarding, they use rpr-plus mode before, how about in sso mode?
Cisco Switching/Routing :: C4510 With Redundancy Supervisor 7E Crashed
Oct 31, 2011Our company's c4510 with redundancy supervisor 7E just been crashed, first the master then the slave. What should I do ?
View 1 Replies View RelatedCisco Switching/Routing :: 4506 Install New Supervisor / IOS Will Automatically Set Everything Up
Aug 12, 2012I have "inherited" a Catalyst 4506 with IOS version 12.2(20)EWA1 and Supervisor IV already installed. We recently purchased a second Supervisor IV and I am looking to install this second supervisor for redundancy. Is there anything special with installing a second supervisor or so I just physically install the new supervisor and the IOS will automatically set everything up?
View 3 Replies View RelatedCisco Switching/Routing :: Failed Supervisor On 6509 Chassis?
Jan 28, 2012swapping out a failed supervisor card on a 6509 chassis?
View 6 Replies View RelatedCisco Switching/Routing :: Nexus 7010 Install New Supervisor
Sep 20, 2012We will install a new Supervisor Engine in our Nexus 7010.One Supervisor Engine is already installed an 1Year old.So the Problem is that both Supervisor Engines may have different NX-OS version.Could this lead to a problem?Does the installed Supervisor Engine "udate" the newer Supervisor engine?
View 3 Replies View RelatedCisco Switching/Routing :: IOS Upgrade On 4507R With Redundant Supervisor
Feb 5, 2013we have 2 Supervisor IV modules in our 4507, i want to upgrade the IOS as its still on 12.2 and i am going to upgrade it to the latest.
my first question is, if i update the IOS on the bootflash will it replicate to the secondarybootflash?
secondly, can i force a reboot of the secondary supervisor, then the primary after the secondary is up? i'm just trying to minimise downtime and get a plan going.
is there a difference in 12 vs 15 that would impact my current config that i should be aware of?