Cisco Switching/Routing :: 8881G-W CDMA Activation / 3G Modem Is Not Inserted
Apr 20, 2013
I have a new 8881G-w router with the following info:
(C880DATA-UNIVERSALK9-M), Version 12.4(22)YB2, Serial No. FTX1331830T
Need activating the CDMA . when I tried to login to the Cellular interface it shows me the following warning:Warning: 3G Modem is not inserted Configuration will not be effective until modem is inserted
I want to activate and configure CDMA and i don`t know from to start..
View 3 Replies
ADVERTISEMENT
May 28, 2012
I understand that the PCEX-3G-HSPA requires and a sim card. I also have a PCEX-3G-CDMA-V. Does this require a sim card as well? And if so, where is the sim card installed?
View 1 Replies
View Related
Feb 22, 2012
I am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies
View Related
May 18, 2010
We inserted a new module with 48 rj45 ports in a 4500 with just one supervisor module. We have two 4500, and we tried the new model in the other 4500 and it´s working properly and giving a OK status. Furthermore, the module´s LED status is green. We saw that there are 8 ports (from 17 to 24) that are in faulty state, so probably this is the cause for the faulty state for the module.
We tried already a Hw reset, replace/insert again the module...
We are almost sure that it can be a Hw failure. We are getting the following results different commands:
show module :
Mod Ports Card Type Model Serial No.
7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAXXXXXXXH
M MAC addresses Hw Fw Sw Status
[Code].....
View 10 Replies
View Related
Sep 25, 2012
how many NM modules can be inserted into cisco 2821?
View 3 Replies
View Related
Mar 29, 2011
I have an interesting problem. I've configured a site to site VPN connection between these two devices. I am using the CDMA card as the primary and only outside connection on the 1921. What happens is that by default the cellular connection is offline. When traffic is generated internally from that network to the concentrator side of this scenario the cellular connection goes online and builds the tunnel, no problem. However, I cannot initiate the tunnel from the concentrator side. I think what i need is a way to force the cellular connection to always be on, and if it fails to come back online.
View 3 Replies
View Related
Mar 31, 2012
The problem is I can't access the router from the internet. I am also an ocean away from the site. I have an ugly hack set up where I access an inside PC with Teamviewer and then puTTy to the router, but it is slow, ugly, and doesn't fix my problem. I need to be able to set up internet accessible servers at this location for VOIP, VPN, and REAL remote access.Everything else works fine. Connection is stable. Speed is kinda ******, but that's not so important.
First off some specs:Cisco 2801c2801-ipvoicek9-mz.124-24.T1.binhwic-3g-cdma-sSprint 3G data plan
Ok, I have set up the previous equipment as a router for a branch office where 3G access is the only available internet access.I have had the excruciating experience of talking with Sprint Tech Support, and would rather shoot myself in the foot than do so again.
Here is what they told me: "They block ports, but they can't tell me which ones."Here is relevant info I have been able to gather.The IP connection the ISP gives us is not NATTED. That is the address at wimi.com and show int dialer 0 is the same one.Most forums say Sprint only blocks port 80.Zenmap (nmap for windows) says the router has NO open ports but DOES exist.Router does not respond to pingsCan't SSH into router from internetCan't access a test local server with port 8080 or 8081 open with the correct nat statement in Cisco routerNo filtering access-list for testing The config should be just fine as a base config for using hwic-3g-cdma-s as the main internet access interface for a router. Everything works fine aside from the lack of remote access.
So in my head it has to be one of 3 problems.
1. The card is doing some weird stuff to incoming requests
2. Sprint is blocking WAN requests on port 22, 2200, 8080, and 8081 and pings (tested). Maybe they block all WAN requests?
3. There is something wrong with my config.
why I can't remote access into my router or things to try with the config?
Below are some config pastes:
chat-script cdma "" "ATDT#777" TIMEOUT 60 "CONNECT"
!
ip ssh authentication-retries 2
ip ssh port 2200 rotary 1
ip ssh version 2
[code]....
View 3 Replies
View Related
Oct 26, 2011
what routed ethernet card (WAN) can be inserted in Cisco 2811? I wan to replace 2Mbps Framerelay to 10 Mbps
View 5 Replies
View Related
Sep 14, 2012
I have a Cisco3800 with IOS Version 12.3(14)T2 and I have an HWIC-1GE-SFP module inserted on it.
I need to know if there is a command to verify optical power level in this module inserted in the Cisco 3800 router?
Something similar to the following command that I can execute in an Cisco ASR9K:
show controllers Te0/0/0/1 phy | i Rx
View 4 Replies
View Related
Feb 27, 2012
Get the message initializing and then it hangs when I insert the sim card. Have a Rogers wireless stick. a Latitude 2023.
View 3 Replies
View Related
May 13, 2012
I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies
View Related
Sep 19, 2012
I am updating the iOS for a 4948 the bootflash is empty so all i can get into is the rommon. There is no option for x-modem. How can I put the iOS onto this device? [code]
View 2 Replies
View Related
Aug 25, 2011
We have successfully activated Protectlink Web but as we have observed that when we try to restart our router, Cisco Protectlink status is active but then when you look on license information on platform the status just states there is "Waiting...."Web Protection no longer working..In order for us to resolve this. We have to restore our router to factory default and then activate Protectlink and set all the settings again..As I have said this only happens when we restart our router?
View 1 Replies
View Related
Oct 12, 2011
I've purchased a used ASA 5505 device. Upon reseting and looking at the startup, I see that it is unable to retrieve Activation License and used default. Activation License shows as all zeros.
Is there a way to find whatever Activation License is tied to my device from Cisco without a service contract ? or I have to live with the default ?
View 5 Replies
View Related
Apr 14, 2013
Bought and paid for Network Magic Pro 5.5. Bought new computer and need to install Network Magic Pro 5.5. Installation successfull. Unfortunately I have lost the activation key and the email it was on was deleted.
View 1 Replies
View Related
Feb 13, 2013
I would like to develop Voice Activation Detection using this sample program (google: ****/p_238-voice-activation-detection-voip) in Visual Studio 2008. But according to this website Visual Studio 2010 is highly recommended. Why VS 2010 is better than VS 2008?
View 1 Replies
View Related
Nov 9, 2011
I work for a small pharmacy that uses a Cisco RV120W router to separate hospital VPN traffic from general internet traffic. The VPN traffic is redirected to a dedicated T1 line (Or T-something, I wasn't involved in the actual setup of the VPN) connecting our store directly to the local hospital, and general internet traffic gets redirected to a ZyXel PK5000Z DSL modem (We have Qwest/CenturyLink 7m/768k). The DSL modem is running the latest version of our ISP's custom firmware.
Prior to installing the VPN and RV120W, LAN traffic was handled with a basic D-Link DI-604 wired router. The router itself was configured with an IP of 10.100.100.254 (With all LAN clients assigned DHCP IPs in the 10.100.100.XXX range) and "WAN" IP of 192.168.0.4, and the modem configured with a LAN IP of 192.168.0.1. The router was connected from it's WAN port to one of the LAN ports on the modem.
The modem has it's own built-in router, but the store owner wished to have an "extra layer of protection", so to speak, and had the D-Link router installed to serve that purpose. Prior to connecting the VPN, a second router was admittedly redundant and unnecessary. However, now that we have the hospital VPN, a second router is REQUIRED to properly separate the VPN traffic from other internet traffic, since the router built into the DSL modem doesn't have the capabilities to perform this task (We had already attempted to operate the VPN over DSL...it failed miserably and spectacularly. A dedicated T1 was the only reliable option).Anyway, when installing the RV120W, we duplicated every possible setting from the old router, including configuring it with a LAN IP of 10.100.100.254 and a "WAN" IP of 192.168.0.4 and connecting it in exactly the same fashion as the old router (Modem LAN to Router WAN). Essentially, the RV120W was set up exactly the same as the old D-Link router, just with the added VPN functionality.
The problem is this: ever since installing the RV120W, we are no longer able to access the DSL modem's administration page (http://192.168.0.1). We were able to do this without any trouble whatsoever with the old D-Link router, but the RV120W seems to be blocking it somehow. Any attempt to load the modem administration page just forever sits at "Waiting for 192.168.0.1...". It never times out, it never shows any error messages. It just sits there, forever trying to load the page, showing nothing but "Waiting for 192.168.0.1..." at the bottom of the screen.
Now, we know for a fact that it is NOT a problem with the modem, because if we connect a computer directly to it via ethernet (Completely bypassing the RV120W), the administration page loads perfectly fine. And, admittedly, we could configure the modem in this manner whenever required. HOWEVER, the modem is located in a rather inconvenient location (In the ceiling, sitting on top of a ceiling tile), and having the ability to remotely manage it like we could before would definitely be something we want to be able to do again...especially since there are plans in motion to install new pharmacy equipment that will require us to do a ton of "trial and error" configuration to the modem.The RV120W has been updated with the latest firmware, yet the problem still persists.
View 2 Replies
View Related
Jan 24, 2012
I have a cable modem with my 2600 Router and i have a little speed problem when I'm going out to the web via my F0/0.. according to regular speed test sites my speed is around 20mbps but when i hook up to my modem directly i get a solid 40mbps.. now I've changed my Cat 6 cable from my modem to my router and this are my settings in the router.
[Code] ...........
I see some drops and lost carriers but not sure what those might mean?
View 2 Replies
View Related
Mar 25, 2012
I've recently tried to update the modem firmware on an 887M that is actually using an Annex M service and after rebooting to kick in the new modem firmware, the router loses sync. I've tried this with various other 877, 877M, 887 and 887Ms on normal Annex A services with no problems, but this Annex M service doesn't like it at all.
View 2 Replies
View Related
May 2, 2012
I'm trying to configure a disco router 2600, my internet connection is via a cable modem. I get a dynamic IP from the cable modem but when I ping to any external IP I have errors.Copy show config and show interface f0/1
GUEST#show config
Using 1103 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[ code]...
View 3 Replies
View Related
Nov 23, 2011
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies
View Related
Mar 20, 2012
We have recently got 2 of our Cisco ASA 5520 firewalls through RMA. These are supposed to run in a Active/Active Failover Pair. There was only 1 RMA request that was opened for both the firewalls. We have received only 1 Activation key for this RMA request for both the firewalls. Just want to check with you if this Activation key will work on both firewalls or do we need a get a seperate one for the other box.
View 1 Replies
View Related
Sep 13, 2011
I went through the install procedure outlined in the ProtectLink Gateway install manual and i activated the ProtectLink Web product through Trend Micro (which shows up through their web site as a registered product to me). It still doesn't show up as installed on the SA540 (under Administration/License Management screen). When I try to activate the product again, it shows as "Already registered". Trend has no idea why it won't work. They said Cisco sold the license, so try their support.
View 1 Replies
View Related
Dec 5, 2011
I sometimes am forced to use my computer at work to set-up wireless networks for employees who move into temporary apartments. Now every time I am at my home, my computer, ipad, and iphone keep redirecting to comcast home activation page. The problem is the home activation page that comes up is for one of the apartments I set-up for my employer. It seems to be stuck on the final steps of this other persons comcast set-up and I cant get it to go away. I have a Linksys router with a secure network. It shows I am connected to my network, but when I try to get on-line it send me right back to Comcast activation page for someone elses account. Countless calls to Comcast have gotten me know where. Since the final steps of the comcast activation involve downloading desk top software, and the ipad will not let you download desktop software even into dropbox. It has made my ipad useless when I'm at home.
View 2 Replies
View Related
Feb 4, 2013
I am facing with Cisco 3560CG Switch. We have a Cisco WS-C3560CG-8PC-S (Cisco Catalyst 3560-C Switch, 8 GE PoE, 2 dual-purpose uplinks, IP Base image) switch which will be a core switch and the internet link from the ISP is terminated on a Modem. The ISP configured the internet modem and provided the details such as Gateway IP, Subnet Mask, DNS IP address, Usable IP Address Block, to configure the switch, where ew have connacted the Modem. When, I verified the details, there were only 4 IP addresses available under Usable IP address block. Spoke with the ISP and they confirmed that they cannot increase the IP Addresses (some limitation on the Modem) in the pool and we have to do NATing at the switching (Which we can't do, because of IP Base image limitation). About the network, it will be a flat network with only one VLAN which is used for Wireless Guest Access.
View 1 Replies
View Related
Oct 8, 2012
I have a Home Virgin media cable connection at home. the only way to get this working with my Cisco gear is by putting the superhub on modem mode.On modem mode, it becomes just a dumb modem assigning and IP via DHCPI can get the switch to get an IP address from the modem with
no switchport
ip address dhcp
then I have created
0.0.0.0 0.0.0.0 fa0/48
to route traffic to the port connected to the mode,The switch gets the assigned Ip address from the modem but it does not route internet traffic.
From the different vlans and subnets on the switch, I can ping the modem.
From the switch I can ping 8.8.8.8
From the machines, i cannot ping 8.8.8.8
On my machines, what should be the gateway? the vlan SVI, the modem's IP address, The fa0/48 ip address? I have tried them all with no success.
View 2 Replies
View Related
Oct 8, 2012
I am moving a very small branch office to a new location, but we have a centrally controlled IT infrastructure team in Europe. I would like to implement a hosted VOIP solution without impacting the current network setup (i.e., VPN/Firewall) or asking this IT team to change anything on the existing LAN Network except the IP address/gateway. The VOIP system will have its own cabling.
Here is the configuration I would like:
• Cisco 861 as main gateway to the Ethernet from the ISP’s modem
• 2 static public IPs from the ISP, one for the VOIP network and one for the LAN
• Cisco 861 acting as NAT/DHCP for the VOIP system on one static public IP
• My company’s Juniper device on the second static public IP managing NAT for the LAN
I have a diagram here to map out what I am considering:
Two options I have seen:
• Setup Proxy ARP on the Cisco router, allowing the Juniper device a transparent (and unsecured/firewalled) route to the internet to get the Public IP and manage the LAN (seen in picture)
• Install an additional switch (with proper QOS prioritizing VOIP) at main entry point of location, and have both routers behind this (to minimize configuration of the Cisco router).
View 3 Replies
View Related
Jul 4, 2011
My customer's Protectlink license is set to expire in 2 weeks. I would like to enter the activation code I just obtained, but cannot find the link. When I go to the license page in the router, there is a link to renew, but that just takes me to the website to enter the new key code, then receive an activation code. There is not howver any link to enter the activation code. I assume that once the license actually expires, the activation link will then show up, but there must be a way to get to this page ahead of time.
View 3 Replies
View Related
May 11, 2013
If I could swap around the bootvar on my 5505 without affecting the activation key.this is to learn different NAT on pre and 8.3+ IOS.
# sh bootvar
BOOT variable = disk0:/asa825-26-k8.bin
Current BOOT variable = disk0:/asa825-26-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
[code].....
View 3 Replies
View Related
Jan 2, 2012
we have a WLC 4404, Software Version 4.2.61.0 and the following Problem. The WLC worked for many years with the SSID "SKHGR". In addition to the existing SSID I have a second SSID "SKHGR-M" is created. The configuration of the two SSID's is identical.
The problem is: when I activate the second SSID, the AP losing connection with the WLC. In the log appears"AP disassociated. ... Base Radio" and "
"not advertising ssid due to radio policy". The AP's connect with the WLC, lose after few seconds the contact.
View 3 Replies
View Related
Mar 4, 2013
We have in our business some RV042 with Cisco ProtectLink Webfiltering. Until now we do not had any problem of activate the licence and it works has we axpected.
But the two last time that we went through the install procedure outlined in the ProtectLink Gateway install manual, the both RV042 do not run the service, we do not know why... So we have decide to stop buy and sold them until we find a solution.
The firmware install are the last one.
When I try to activate the product again, it shows as "Already registered". Trend has no idea why it won't work. They said Cisco sold the license, so try their support.
View 1 Replies
View Related
May 19, 2013
I am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies
View Related
Mar 19, 2012
we using Linksys router for Internet for different vlans now we take 3750 as core switch for another different vlans 10,20 we create v Lans 20,20 also create cpd servers and we need Internet for vlans 10,20 through linksys router how should we configure?
View 5 Replies
View Related
