Cisco :: SNMP-OID To Poll Values Of The CPU-load From VSS 6509E
Jul 4, 2012
i am searching for the right SNMP-OID to poll the values of the CPU-load from a VSS (6509E)here a OID for VSS-Switch1 and a other OID for VSS-Switch2 values like cli-command "sh proc cpu" of the supervisor-module in slot 5.
View 1 Replies
ADVERTISEMENT
Apr 18, 2012
I have two Nexus 7010 in the data center. I'm unable to poll SNMP data from one of the NEXUS 7010s. The other Nexus 7010 is working fine. I have compared the SNMP configurations, and they are identical. When I do "show snmp" on the non-working switch, I have SNMP packets in "Unknown Context name", not sure why. I have done show vdc and it matches the working switch output. Here is output of show snmp from the non-working switch: 133 SNMP packets input 0 Bad SNMP versions 0 Unknown community name 0 Illegal operation for community name supplied 0 Encoding errors 0 Number of requested variables 0 Number of altered variables 0 Get-request PDUs 0 Get-next PDUs 0 Set-request PDUs 0 No such name PDU 0 Bad value PDU 0 Read Only PDU 0 General errors 0 Get Responses 133 Unknown Context name0 SNMP packets output 0 Trap PDU 0 Too big errors 0 No such name errors 0 Bad values errors 0 General errors 0 Get Requests 0 Get Next Requests 0 Set Requests 0 Get Responses 0 Silent drops.
View 4 Replies
View Related
Nov 8, 2011
I want to get the result of the following command with snmp. Is This possible?
The command is "show extended channel 2/0 csna oper". I need to know, if the status is "closed" or "setupcomplete". Can I catch these values with snmp?
I did a snmpwalk but can´t find any lines with these values. Is there a specific IOS version necessary?The hardware is a Cisco 7204VXR with IOS 12.1(5)T10 and microcode xcpa28-1
View 2 Replies
View Related
Nov 2, 2011
we are seeing network latency problems and our cpu on the 6509e is spiking and have a above average % for the past week or so. When we do see these spikes it seems that snmp and apr input is high
CPU utilization for five seconds: 75%/53%; one minute: 17%; five minutes: 14%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 9 1636168 95505 17131 4.19% 0.36% 0.34% 0 Check heaps =======>
12 478096 1011864 472 3.07% 0.12% 0.12% 0 ARP Input =====> 52 30420 436000 69 0.07% 0.07% 0.07% 0 Per-Second Jobs
53 317496 7789 40762 0.87% 0.10% 0.06% 0 Per-minute Jobs
220 55380 87807 630 0.07% 0.06% 0.07% 0 Compute load avg
[code]....
we recently upgraded our 3560 switches to the new 12.2-55 ios version but have not upgraded our 6509 because its ios is on 12.2(33)SXJ1. Not sure if this is related or not but it seems that after we upgraded to the later ios that the latency started.over the last 24 hours the spike is several times an hour and at least one a day that it hits the 90 - 100 % mark.is there a way that we can limit what snmp view but would not effect functionality or network?
View 2 Replies
View Related
Jan 8, 2013
What are the best values for "mac address-table aging-time" and "arp timeout" by following scenarios?:- single sg300-10 as layer3-switch with a maximum of 10 local (direct connected) hosts - and a 3750x-stack with 100 local hosts + hsrp with a other stack of the same sort or for asa 5520 as internet gateway for 500 clients?I use at the moment a mac aging-time from 300 seconds and a arp timeout from 3600 seconds.
View 6 Replies
View Related
Sep 18, 2011
tried to read the NEXUS 5000 cpu load: cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1 but there is a timeout: Timeout: No Response from 10.100.224.16 Other MIB values readout, like the system value, is ok.We use snmpv3.
View 4 Replies
View Related
Jun 20, 2012
I use a cisco 2620 voice gateway with a module NM-HDV-2E1-60. Tell me how you look at snmp for Cisco 2620 load E1. For 2811, I found oid 1.3.6.1.4.1.9.10.19.1.1.4
View 4 Replies
View Related
Jan 9, 2012
I have CiscoWorks 3.1.
1. When creating job or log file, these files are always stored in the default Path (inside LMSROOT) for RME for example...Could I change RME default Path to store these files in another location inside the Hard Disk?
2. Could I Configure CW-LMS to send all the reports to me by mail?
3. What is the Difference between Poll Interval time and Collection time inside RME?
View 2 Replies
View Related
Apr 18, 2013
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies
View Related
Aug 1, 2012
I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies
View Related
Dec 6, 2011
Now, with all the unified communications, voice, video and data are in the same device, and I try to give priority to voice and some applications, but in the WLC I can not find the way to mark all that kind of packets.
Is it possible to do that? like in a LAN making the marking as voice, signaling and any kind of application? as I marked in all the LAN.
the equipment:
WLC 5508 v7.0.116
AP 1142N
View 5 Replies
View Related
Oct 6, 2010
I am running ACS 5.2 (more detail below) eval demo version for a proof of concept and noticed an oddity.. It appears that if you create a Endstation Filter and click the CLI/DNIS tab, click Create and then click DNIS and enter your info ex: *coolssid and hit submit it shows everything correctly, but if you go back and edit it. it swaps them.
Version : 5.2.0.26Internal Build ID : B.3075.EVAL..If you have the webex recording viewer you can watch the little Webex Recording I did showing the steps and the issue.
View 6 Replies
View Related
Feb 2, 2012
We purchased a Cisco 541w router for one of our customers.
The main reason was to provide them with 3g backup solution for their business.
In order for the router to recognise the 3G router the firmware was upgraded SRP540_1.02.01_023_081211_1136.
We arrived on site last night to do the install but couldn't make any changes to the already configured router. Every time we attempted add a vlan or adjust the dhcp scope the router would return "The values are invalid".
Worked at this for over 1 hour and then decided to factory reset the router to see if that would revert the router to use the original firmware.
This didn't revert to the previous firmware but we magically could now make network changes without problem.
So everything was good, we reconfigured the router, tested 3G and failed the wan1 interface back and forth and the customer was very happy.
Customer arrived onsite this morning and the router was running on 3G. Every 8 - 10 minutes it was attempting a failover between connections.
I decided to turn off the failover for the time being and investigate further but yet again i was back to "the values are invalid"
We've had to pull the router as the customer is about 2hours away and revert back to their BT router.
Found this document for another SRP model - A warning message may appear in the Basic Wireless Settings screen with the text “The values are invalid” when modifying the wireless profile. Set the SRP 521W to its default setting (CSCtd49614).
[URL]
Will firmware SRP540_1.2.4_003_011112_1847 released only 2 days ago cure the problem?
View 1 Replies
View Related
Oct 17, 2011
I have a WLC 2106 with 3 APs. Everything works and users can connect, but the throughput seem to be lower than it should (it is around 8Mbps and should be around 30-50Mbps). And all speed and duplex has been accounted for.
I am trying to understand the stats that I see for the 802.11 MAC counters I under the Wireless APs.on the controller.
That screenshot is attached. I see high numbers for the following areas:
- Tx Failed Count
- RTS Failure Count
- FCS Error Count
what these mean and what could cause this? Maybe these are normal and not a concern.
View 1 Replies
View Related
Sep 1, 2011
my cisco 2611 series router is showing garbage value at start up and not allowing me to enter in Romon mode I check the bitrate in console .it is 9600/8N till then i am unable to start the router Can you tell me how to change configuration register value without entering in rommon mode
View 6 Replies
View Related
Sep 24, 2012
I am scanning the documentation for CPI 1.2, trying to get it to use CSACS 5.3 for my authentication/Authorization. The docs say to create a TACACS Shell Profile, and add the TACACS A/V Pairs as needed... . nowhere could I find a listing of AV Pairs I can use to grant authorization. I did see that what ever pairs I did use, I must keep the menu chain in tact..
View 6 Replies
View Related
Dec 10, 2012
how to perform Linear Hashing in databases on given values?
View 2 Replies
View Related
Oct 18, 2012
Type of Wireless Adapter I have: Intel WiFi Link 1000 BGN When I click on (Properties) and then click the (Advanced) tab, there is a list of properties on the left and a list of values to choose from on the right. I'm curious on what each property does and, which property/value would be most "effective" or "appropriate" for a certain location/situation I'm in.
View 1 Replies
View Related
Apr 16, 2012
I have a WS- C2924C-XL switch that I would like to upgrade the IOS version on. The IOS version in question can only be installled on an 8MB version of this switch, I have tried to confirm the amount of memory present in the device but I am getting conflicting values depending on where I look.The model number would indicate that this device is a 4MB version, therefore not compatable with the upgrade.Running the show version command from the CLI shows Processor having 8192K/1024K bytes of memory.Accessing the switch via the VMS management interface displays a value of 4MB.
View 5 Replies
View Related
Oct 30, 2011
I'm looking at a stack of WAP200 and WAP4410N APs. I'd like to use Cacti to track number of associations on each AP.What's the OID I should be querying? Are there multiple OIDs that would correspond to the multiple SSIDs? I'm running 2 SSIDs on all of them, and it would be extra nice to be able to track number of stations on each SSID, though the total number would also be acceptable as well.
View 4 Replies
View Related
Apr 29, 2012
I've been working on a 3560 that doesn't seem to map dscp values to a new value: mls qos map dscp-mutation ToR1 22 24 to 46
[Code]....
On the router on the other side, I created an acl that matched on dscp 46, but it doesn't match on it. I've tried moving the mutation map to the ingress interface and I've tried setting dscp with a service policy instead of marking COS and using internal dscp. Where is the mutation map supposed to be placed: ingress or egress? Also, I added an entry in the acl on the router to see if I was mapping to dscp 24, and I am:
[Code]....
So it seems like the mutation map is being ignored completely. Any reason why?
View 7 Replies
View Related
Jan 10, 2013
I have a switch where the current power threshold is set to -20.0db. The problem is that the receive power fluctuates between -19.9db to -20.1db, which is causing it to throw alarms on my solarwinds monitoring server. What I would like to do is change it to a different warning threshold, but I can't seem to find the command to do so. This is a catalyst 3750 running IOS version 12.2(55)SE3. [code]
View 5 Replies
View Related
Feb 4, 2010
We have a C4500 with 2 sup V which is showing high CPU values sometimes.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 65% The show platform heath command gave me a high reading for K2FibFC DelFlow which is about 50% at this peak but is normaly around 1%?
what the process K2FibFC DelFlow means and what could be the cause of this peak?
View 12 Replies
View Related
May 16, 2013
Access point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies
View Related
Mar 20, 2012
I've been having a debate with a colleague about QOS COS values. My colleague says I need to use COS values across layer 2 trunk links between access layer switches and core switches. My argument is if phones are marking packets with DSCP values I don't need to be concerned with Cos.The reason I ask is we're implementing a new phone system, the ip phones will mark RTP traffic wih dscp value EF and Call signaling with DSCP value of CS3. If my understanding is correct I can trust the dscp values of the phones. We are using Cisco 4507 switches which I believe automatically trust dscp values so I would just need a class-map to match the dscp values and apply the output policy map on the egress interfaces as follows? [code]
View 3 Replies
View Related
Oct 14, 2012
We have a 4500 series switch that is running around 39% cpu utilization but seems to be dragging a bit. I did a show platform health and GalChassisVp-review has a target of 3% but an actual of 17%. All other actual values were at or below target values. I then went to show platform cpu packet statistics and in the "Packets received by Packet Queue" all queue packet values at 5 sec, 1 min, 5 min and 1 hour avg were either 0 or 1 with the exception of Esmp - that averaged 351/377/317 and 313 respectively. I then checked show platform hardware acl input entries static and the entry type InputEsmpToCPU had a whopping 10121370 hit count. All other entry types were well under that number.
View 2 Replies
View Related
Oct 26, 2011
I'm working on a catalyst c3750 and for my work i need to prioritize certain streams independent of their bandwith usage.
The streams are the following:
- voice
- video
- data
I created policy maps based on vlans like below:
policy-map VOICE
class class-default
set precedence 5
policy-map VIDEO
[Code]...
View 7 Replies
View Related
Oct 19, 2011
I have a stack of 4 Cisco WS-C2960S-48FPS-L switches running c2960s-universalk9-mz.122-58.SE1 code. One of our network monitoring tools is indicating discards on a certain port on the switch. Upon further investigation I am seeing the Total output drops values change in a very odd manner.
The numbers seem to go from 573 to 1146 to 1719 then back down to 573 and it starts the same pattern over: [code]
The port utilization is quite low, the highest I've seen over the past 7 days is 3.5% with a polling period of every 30 seconds using Statseeker. Yet the discards are bouncing all over the place.
I've searched though the bugs for 12.2(58)SE1 and didn't see anything.
View 13 Replies
View Related
Jul 8, 2012
I have Switch 6509E wich is the core of the network, and we have 4 llink form 4 ISPs, all the link will work at the same time?how can I confiugure the BGP , as I know if I configure bgp it will work with one ISP as an active link,if that link goes down it will automatically begin to work with other ISP. My question is that how can configure the network so that,some vlans work with one ISP, some vlans with the others and so on.If configure it with route map I will have to track every time to change the confiration if the links goes down, but I do not want to track it, Can I do anything with BGP to implement this task?The core of the network is Switch 6509E, intervlan routing is implemented on it, no dynamic routing is enabled.The firewall module installed on it the implementing the NAT processes.
View 7 Replies
View Related
Jan 13, 2013
I recently bought an EA4500 specifically to utilize the QoS feature. I have my xbox in the set up for the prioritization, but when I try to set the bandwidth to 250 kbps upload, it resets to 0. My xbox is hardwired to the router and I know most of the feature set of this particular router is geared towards wifi, but I would assume the QoS settings would apply to the wired devices as well. exchanging this router for one that supports DD-WRT?
View 8 Replies
View Related
Jun 2, 2013
I am using 10Gig link to connect distribution and access switches. Since we are terminating the cables at multiple locations, we are also doing the link budgeting. The CISCO SFP 10G-LR module data sheet shows two values for the transmit power one of which is maximum power .5dBm and another is minimum power -8.2 dBm. Which value should I choose for the link budgeting.
View 1 Replies
View Related
Jun 1, 2013
I am having two 6509E working in VSS and both are working fine. But the configuration register of command "remote command switch show boot" is 0x8000 which is different from that of RP (0x2102) .Now i want to change the value of configuration regsiter of SP to 0x2102.
View 1 Replies
View Related
Sep 20, 2012
I multi homed to dual ISPs using a single 6509e. Currently, I am only receiving a default from wash ISP and marking one with a higher local pref. most of my traffic flow is inbound, so this config meets my need. The issue I have: if either ISP has has an outage upstream from my directly connected peer, my router does not detect that and continues to send traffic out thru that provider only to be black holed. My 6509 will only support 256k routes, so full route tables isn't an option. I could receive partials from each ISP. Is there any other method to detecting this upstream ISP issue and then adjusting my local pref on my default to use the alternate provider path?
View 3 Replies
View Related