1. Do all the 2800 series have a rocker power switch on the rear?
2. Do all 2800 automatically power on when power is connected if the rocker is in the on position?
3. Is it possible to physically damage the flash card in a 2800 router if it was powered off during a write operation?
The story is I have a client who claims that the flash card was damaged due to a power off.
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies View RelatedI have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies View RelatedI just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedHow to add a wic-2t card on router 2800
Had the card as follows
I want to know routr 2880, such as the following picture
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View Relatedhave remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
Is there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedI need to take the Latitude e5420 into secure areas that do not allow wireless of any kind. OS level disable, or even BIOS disable are not acceptable. I need to brick the bluetooth transceiver.
View 1 Replies View RelatedI know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
Just setup my new EA6500 router and while in general it seems to be performing ok I am experiencing some problems with the admin. It seems that frequently either via cloud or local i get the cannot find router message or waiting graphic which results me in having to manually reboot the router so that i can access the admin page again, The router still works fine but no admin access until i physically reboot. This kind of defeats the whole purpose of using cloud if just by accessing the router or making changes it leaves admin access inoperable!
View 9 Replies View RelatedI am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedWe've just discovered it seems the 2800 series aren't getting IOS 15.2?
We're running a 2851 for our CME and specifically want some features in CME 8.8...
End of Sale has been announced, but as it stands you can still purchase this router new today.
I have two CISCO 2800 routers tied together over a Metro Ethernet bewteen an HQ location and a Colocation facility. There are multiple subnets on both sides of the MAN. All things work in this regard.
I added two new Interfaces to the routers to create a VPN failover should the above MAN go down. I use IP SLA to track the MAN, then move to the VPN route when reachability is down.
I can source ping from one CISCO router Interface to the other, through the two interfaces to the Sonicwalls and reach the router interface of the CISCO on the other side of the VPN tunnel.
Problem: I can not ping any subnet behind the interface I ping through the Sonicwall VPN tunnel?
Example 2800 G0/2 interface 100.1.1.41 /30 through Sonicwal over Internet to other Sonicwall and out ot the G0/2 100.1.10.41 /30 interface on the other 2800 router. Ping is fine.
I am having an issue with a VPN tunnel in that we can only establish this from the VPN 3k side to the 2800 and not from the 2800 to the VPN 3k , the setup is as follows: [code] I am awaiting the logs from the VPN 3k but here is the debugs from the 2800. [code]
View 4 Replies View Relatedi hace a VPN configured between two Cisco ASAs, but I have a problem to reach a network behind a router 2800.
View 7 Replies View Relatedwe have anew office and have a 2800 router as a WAN router it has a 3G card and a DSL link. We have a ASA which has to be configured to 2800 router. we want that ASA shd have a VPN link with pirmary site over DSL if DSL fails it shd automatically fall to 3G....what we really need and how it would be done interims of IP addressing do we need any special IP from service provider.?
View 2 Replies View RelatedI have configured the netflow to gathering flow from my cisco 2800 as below:
interface GigabitEthernet0/0
description ### To VNPT_FTTH_20M ###
no ip address
ip flow egress
ip route-cache flow
[Code]...
But i still not see users addresses(each individual hosts will go though) What and where i am configured wrong? I also attached here the map network.
First some info:
System image file is "flash:c800-universalk9-mz.SPA.152-4.M1.bin"
Cisco C819HG+7-K9 (revision 3.0) with 492620K/31667K bytes of memory.
[code]....
The strange thing is....I have a running-config if i ssh to it. but according to my flash: there is only my IOS.BIN. How is that working?
Where the latest working image can be found. because Cisco states the the one right now i the right..but still i cant see cellular 0 in CCP
I think I am having problem with my network card I am running windows 7 with Dell wireless 1390 WLAN Mini-Card lots of times the signal is low and I get the error message no internet connectivity or some other error message that I am not being able to connect to the network provided by my wimax modem, Is there any program that I can download to test if there are any errors related to the network card or any way to fix this?
View 3 Replies View Relatedwant to ask something about configuration ruter 2800I already have a usb to DB9 | DB9 to RJ45but i have a problem like the image below
View 19 Replies View RelatedI have a Cisco 2800 router. I have been noticing a lot of traffic to Pandora lately. At times my pipe is 25% music streaming and my router utilization can be quite high. Our web filtering is a hosted service that does not block all traffic depending on some of the ports. It is really designed for port 80 and 443 only.
We decided we want to block access to Pandora completely on both our primary internal LAN's and our Guest wireless LANs.
When I perform the ARIN lookup, I get these results for the IP range:
NetRange: 208.85.40.0 - 208.85.47.255
CIDR: 208.85.40.0/21
The CIDR notation does not make sense to me entirely. The IP range includes 8 class C networks. The /21 is a class b subnet of 255.255.248.0 or a router broadcast address for routing tables (depending on how you want to look at it). I was not sure if I could block the address based on the router CIDR range of if I had to use the individual classful IP ranges.
Should I block "208.85.40.0 0.0.7.255" in my ACL or should I create 8 entries to block the networks like this?
208.85.40.0 0.0.0.255
208.85.41.0 0.0.0.255
I am operating a 2800 series Cisco router. The router is working fine except that I am not able to SSH into the router. I have checked the running config with cisco's documentation and every line is correct. Prior to me getting this job they did an update and think they have corrupted the a certificate key for SSH.
Any command to generate just the SSH key and not all the other keys that would cause bigger connection issues.
I have 2 2800 series routers configured the same, but with different subnets. One works fine, the other the client can't obtain an IP, and hardcoded, cant ping.
I ran DHCP debug and I can see the router assigning the IP, and I see and ARP entry that matches the MAC of the client.
*Feb 24 11:33:55.915: DHCPD: Sending notification of DISCOVER:
*Feb 24 11:33:55.915: DHCPD: htype 1 chaddr 000a.e40c.d232
*Feb 24 11:33:55.915: DHCPD: remote id 020a0000ac10760101000078
[Code].....
We have a customer in the UK, who is starting to deploy ADSL2+ circuits for the new sites they are adding to their BT IPClear MPLS network.We want to standardise with a config for each site, but to date have found that we seem to be using a different config for each site. Some are configured using a dialer interface & some using a virtual template.
Why on some of the sites the virtual template method works & on others we have to configure a dialer interface. Also in regards to the speeds, what should we configure as bandwidth statements & also for traffic shaping. I know that the ADSL2+ circuits can operate at various speeds, but am i right in thinking these higher speeds are the clock rate of the line & with the BT IPClear product, the customer only gets the agreed/paid for bandwidth.
As this figure is different in both directions, when the traffic shaping is configured using vbr-rt command, is the amount entered based on the slower upstream bandwidth on the circuit.
Local LAN is connected with cisco 2800 router and SRX 210 Firewall, currently all LAN segment will go to my Data Center via ISP A and all internet traffic from LAN segment will go to internet via SRX firewall, there is no relation/connection between cisco router and SRX firewall. I have separate AS no. s for both the ISP
I am having attached scenario. based on current one I would like to do following.
1. I need to use PBR at LAN Switch ( its L3 Switch) such that in normal scenario - local VLAN traffic is equally distributed on both ISP.
2. dedicated internet traffic will flow through ISP B only and if WAN link of ISP B goes down, the internet traffic will pass through ISP A.
( in normal scenario, ISP A will utilized 100 % for LAN traffic to reach it to DC but once ISP B link goes down, the b/w of ISP A will be divided to route 50% traffic for LAN segment to DC and rest 50% traffic of LAN segment to internet)
My client has about 15 public IP addresses for their WAN network. All the internal network IP will be dynamic NAT to these 15 IP addresses to communicate to Internet. Since they are dynamically NAT, if anybody want to access my client internal network from outside internet, we usually advise them to use the whole range of IP.
The modem router used to dynamically NAT these 15 IPs are Cisco 2800.
I am thinking of the configuration using WAN DDNS on this Cisco 2800 for combine these 15 IPs to a DNS name by DDNS method (or any other way beside the DDNS) so that outside people can use one DNS name instead of whole range of IP. In case there is limitation of configuration of some outside people can use only one setting instead of one whole range of IP, they still can access by using one DNS name.
How to implement this on Cisco 2800?
find the firmware file for 2800 series router? I need to upgrade the firmware to this router to get adsl annex M mode to work.
View 1 Replies View RelatedI have an IOS upgrade scheduled on a 2800 router and I have to erase the present IOS. This is a remote location. I am worried that if the new IOS does not work properly that the router will boot in Roman mode. I would still have access to the router via a modem connected through the console of the router.How would I upgrade a router IOS in Roman through a US Robotics Modem connection on the console the router and using a US robotics on my desktop computer to dial into the router? I cannot locate any documents on the Internet about this.
View 1 Replies View RelatedI need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies View Related