Cisco Switches :: SFE2000 Saving And Loading Configuration?
Apr 10, 2011
I have a number of SFE2000 10/100 24 port POE switches. They are configured and running OK. I want to be able to save the configuration and be able to load that saved configuration into another new swich in the case of a failure.
I have logged in and gone to Admin-File Management-Save Configuration. I then select the 'Backup' radio button and TFTP the configuration to my TFTP server. All works OK and I have a readable text file with the switch configuration on my TFTP server.
I want to be able to restore that saved configuration on to a new switch. I have set the new switch back to factory defaults. I go to Admin-File Management-Save Configuration. I then select the 'Upgrade' radio button and try and uploade the file into the switch. If load to 'Running Configuration' the switch shows a status of 'Copy Finished' but says 'Copy completed with errors' If load to 'Startup Configuration' the switch shows a status of 'Copy Failed' and says 'Copy completed with errors'
I am guessing I should be able to load my saved Configuration back into a switch, shouldn't I??
And yes the switches are running the same firmware 3.0.0.17
View 7 Replies
ADVERTISEMENT
May 3, 2011
I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies
View Related
Oct 7, 2012
Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
View 2 Replies
View Related
Dec 15, 2011
Is there a CLI, other than the terminal mode menu, for this switch? I would much prefer to use a CLI to configure it than the (web) menus available.
The web menus are confusing and the manual is long. I already know how to configure Cisco Switches via the CLI quite well.
View 3 Replies
View Related
Sep 25, 2010
I have setup a new SFE2000 switch to work in Layer 3 mode using the IP address 192.168.100.254 on VLAN 1.I would like VLAN1, 2, 3 and 4 to be able to communicate with each other while VLAN2 (Guest) needs to be restricted from everything except web access and dhcp assignment from our server.I have been playing with various ACL's in an effort to accomplish this but so far I have drawn a blank in getting this working.
View 3 Replies
View Related
Oct 8, 2012
I'm having 1841 Router, its configuration is not getting safed. If I reboot the router all my running-config is like default. But when I check my sh startup all the configuration which I did is displayed. Checked the config-registery too and its 0x2142 changed too 0x2102 still the same problem, when reloading the router all the running config is disappeared.
View 2 Replies
View Related
Jan 18, 2012
I have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies
View Related
Feb 3, 2013
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
View 2 Replies
View Related
Nov 10, 2011
I have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
View 5 Replies
View Related
Aug 15, 2012
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
View 5 Replies
View Related
Oct 3, 2011
When I try to save the configuration it displays the following error.Is it due to insufficient memory?
MPF-ASA#wr mem
ERROR: % Unrecognized commandMPF-ASA(config)# wr memBuilding configuration...Cryptochecksum: 81c514b8 9e95ee97 8b512148 b31377a4
[Code]...
View 1 Replies
View Related
Aug 25, 2012
With firmware 1.0.4.17 I am have issues with configuration pages not loading and needing to restart the web interface and login again. This is a new problem that started after updating to 1.0.4.17
How many months until we can expect a fix?
View 3 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
Nov 20, 2012
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
View 2 Replies
View Related
May 22, 2012
I have a WRT54G with updated firmware. Today I saved my configuration to a config.bin file. When I tried loading the file, the admin screen went blank. Now I am no longer able to access either the internet or the router's admin page. Is a hard reset my only option?
View 6 Replies
View Related
Mar 5, 2013
I recently bought a Cisco SG200-26P and now loading webpages are sometimes very slow or don't load at all.I have to refresh to page to load at all and sometimes even restart safari to load the webpages.I have this on several macs and ipads.
View 3 Replies
View Related
Jun 26, 2011
I have a Campus LAN setup which is layed out using Cisco SRW2024 and SGE2000 SB switches. On the LAN we are running various services. These are CCTV, VOIP(SIP), Public Address(multicasting) and Internet hotspots to various locations. I have attached a layout of the setup. A unique VLAN is setup for each of these services.The problem we have is that the PA audio is breaking up at intervals making the output distorted this is also happening for the SIP phones within the facility. Using the user guide we have tried to setup QoS on the system but we seem not to improve the services.
View 2 Replies
View Related
Aug 21, 2011
How to erase or remove configuration file from ESW 500 Series Switches?
View 2 Replies
View Related
Feb 11, 2013
I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies
View Related
Sep 5, 2012
I just recieved a WAP4410N and managed to log in to the web interface. It is not allowing me to change many settings. I try to change the wireless network mode and click on save and it goes back to disabled again.
P.S. I have just upgraded the firmware to 2.0.3.3 and tried to set it back to the factory defaults. neither worked.
View 1 Replies
View Related
Apr 17, 2012
On a Microsoft xp network when we log off or shut down (randomly) users will have their computers lock or freeze at saving settings. The network is school district with around 1000 computers total.
-We think it is an issue with DNS or DHCP but we can not find anything only about our issue.
-It occurs randomly, but seems to target certain machines more. In a lab about 3 quarters of the computers are not affected and the other quarter will have it happen, but not every time. It will happen on student, teacher, and admin accounts.
-It has "spread" to 3 buildings now. At first it seemed to be an issues at one building but over the course of a week two new buildings are affected.
-No major changes in our network over the past month either.
View 5 Replies
View Related
Mar 6, 2013
I have 3com router and it is working fine. The issue is that when I am taking the router out of the electricity and reenter it back it will not save my settings and I will have to log in again to change the settings.
View 1 Replies
View Related
Apr 8, 2011
I have a new DIR-655 and have successfully added three access policies. I am trying to add a fourth, and have gone through the wizard making all the necessary entries. After saving, I get back to the list of existing policies, but the one I just added does not appear.
View 2 Replies
View Related
Nov 21, 2011
I was configuring a new Catalyst 2960 switch and had forgotten to set the speed back to 9600 after downloading the new IOS software image. I finished doing all of my configurations and went in to line con 0 to change the speed back to 9600. The change was accepted and I did a 'wr' to save the change, but when I reload the switch it is back to 115200.
View 3 Replies
View Related
Aug 23, 2011
I am trying to put a link on our Intranet page to several documents that are updated daily by specific users. These users save the documents in their department folders, which are only acessible by their department and I.T. (me). Right now I have a .bat file that checks every half hour of the work day to see if it has been updated, if it has it will be moved to a location in the Intranet folder which will update the link on the Intranet. While users can view the Intranet, they do not have access to view the files or folders that house the Intranet html coding etc.This option works but our users are complaining that it isn't instantaneous. Any ideas how I can do this on a network while keeping everyone's security in place and not give them extra rights to the Intranet folders?
View 3 Replies
View Related
Nov 30, 2012
I'm not sure if this is even possible, but I'm currently changing from saving my documents on my desktop to a server. However, I like working with files from my desktop for ease of use. Is there any way to save a document in the server, while working with the document as it exists on my desktop (e.g. set the file up to save in two locations)?
View 1 Replies
View Related
Jan 23, 2011
I have a laptop that travels alot to different networks. I go to two differnent networks where I need to enter static network settings (wireless nic). How the heck do you save these settings so I don't have to enter them all the time. I know you can save the network profiles but does this save static settings assigned to the wireless nic?
View 3 Replies
View Related
Sep 9, 2012
I am having difficulties saving, loading conifg files from a USB, what is the correct command for loading a config file from USB for cisco 3750x switch.
View 1 Replies
View Related
May 28, 2012
We have PC's that connect through the Siemens IP phones and back to the cisco 3750 which is connected to our core 6500 via L3. The phones use a voice VLAN and the PC's use another VLAN. The whole setup seems to work ok but I was just wondering if the QOS was configured correctly. Our current config on our 3750 switches are mls qos trust dscp on the port that connects to the phone and PC and mls qos trust dscp on the L3 links. The phones are configured for "QOS L2/L3"From the reading I've done so far it seems that any ports connected to a L2 device should be set to cos and not dscp?
View 16 Replies
View Related
Apr 6, 2012
How do I make the following work with Cisco 302-08G ? I have a 4-port Cisco wireless/wired router that allows for a guest account. I also have Cisco SF302-08 that I bought so I could use its port/vlan mirroring capability. How should I configure the network, given the aforementioned equipment, so that I can get a single point sniff.
Assume I have two wireless clients, one using the "regular" wireless SSID, and the other using the "guest" SSID. I can see 192.168.1.x (regular SSID) and 192.168.169.x (guest ssid) on the internet side (one the same physical cat5 of the wireless router. So far so good. But, I would like to use 302-08 to actually allow the guest SSID/network comm cable)unicate with the regular SSID/network. For example, if I ping 192.168.169.x from 192.168.1.x, I would like to see a response. Can I make them communicate properly with the 302-08 ?? if so, what do I need to do ?? (I will also have wired clients tied into the 302-08..so its important that it be the central sniffer point).
View 2 Replies
View Related
May 11, 2012
I'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view. Here is the view of my Front Panel view after I connect the switch ?
View 2 Replies
View Related
Aug 24, 2012
I'm adding it to an existing infastructure, with multiple VLANs. I believe I have it set up correctly, however whenever I daisy-chain the switch in with the trunk ports, it's not passing the VLAN info correctly. There's not a lot of configuguration involved, so I'm not quite sure where I might be going wrong. I've attached a couple screenshots that show my trunk port configuration.
View 3 Replies
View Related
May 2, 2013
I have been trying to setup vlans on a SG300-28p but they are not working. This is my setup: I want Switch1 to have ports 1-10 to access the DMZ, and 11-24 the LAN. Then i wan to add switch2-4 to extend the access to LAN.
i tested with cisco 2960 switches by just telling what ports whould have access to DMZ and LAN but the small business switches are different..
View 1 Replies
View Related
