Is there a CLI, other than the terminal mode menu, for this switch? I would much prefer to use a CLI to configure it than the (web) menus available.
The web menus are confusing and the manual is long. I already know how to configure Cisco Switches via the CLI quite well.
I have setup a new SFE2000 switch to work in Layer 3 mode using the IP address 192.168.100.254 on VLAN 1.I would like VLAN1, 2, 3 and 4 to be able to communicate with each other while VLAN2 (Guest) needs to be restricted from everything except web access and dhcp assignment from our server.I have been playing with various ACL's in an effort to accomplish this but so far I have drawn a blank in getting this working.
View 3 Replies View RelatedI have a number of SFE2000 10/100 24 port POE switches. They are configured and running OK. I want to be able to save the configuration and be able to load that saved configuration into another new swich in the case of a failure.
I have logged in and gone to Admin-File Management-Save Configuration. I then select the 'Backup' radio button and TFTP the configuration to my TFTP server. All works OK and I have a readable text file with the switch configuration on my TFTP server.
I want to be able to restore that saved configuration on to a new switch. I have set the new switch back to factory defaults. I go to Admin-File Management-Save Configuration. I then select the 'Upgrade' radio button and try and uploade the file into the switch. If load to 'Running Configuration' the switch shows a status of 'Copy Finished' but says 'Copy completed with errors' If load to 'Startup Configuration' the switch shows a status of 'Copy Failed' and says 'Copy completed with errors'
I am guessing I should be able to load my saved Configuration back into a switch, shouldn't I??
And yes the switches are running the same firmware 3.0.0.17
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies View RelatedI have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
View 3 Replies View Relatedwhy i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies View RelatedI have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies View RelatedI remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies View Relatedi am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Replies View RelatedI have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View Relatedi have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View Relatedi have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedI have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedI have a SF 300-24p.... How do I configure it to act use like a hub, with the uplink on G1... And How do you set all the ports to POE for ViOP phones, and these ip phones are going to get DHCP over network..
View 1 Replies View RelatedI bought for a little office a SA520 Security appliance (for future VPN with another distant office) and a SG 300-10P switch for connect 3 PC and 3 IP PHONE. THe SA 520 is the router. I must configure 2 VLANs on the switch :
VLAN2 : DATA (for PC)
VLAN3 : VOICE (for IP PHONE)
VLAN1 : DEFAULT.
How can i simply configure all ports ? I would like to configure ports 1-4 on VLAN2 and ports 5-8 on VLAN3 and port G10 is reserved for the router SA520. I want to divise network DATA/VOICE.
I think i must create a trunk on G10 for SA520 ...
I would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies View RelatedI am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies View RelatedI've to connect 2 building with fiber, for this I use 2 HP baseline switches.How do I have to configure the 2 switches so that i can have PC connected to switch 2 able to "talk" with the server connected to switch 1 ?
View 9 Replies View Relatedhow to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
i purchased 300-28 how it config for stp and trunk
View 2 Replies View RelatedI have a question regard to switch SFE2010P, i have 2 vlan ( data and voice) and we want to configure Ip phones SPA502G, the question here is how can i make to suport 2 vlans on the same switch port, like the catalyst IOS switch port acces vlan x and switch port voice vlan x, if i set up the switch with the voice vlan like tagged doesn't work, but if i set up the voice vlan like untagged vlan its works but the PC attached to the data port on the SPA502G doesn't work?
View 1 Replies View RelatedI am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
how do i configure cisco switch Edge
View 1 Replies View RelatedHow config dynamic alp inspection for 300 or 500 series ? I find in admin guide it's no simple to do.
View 8 Replies View RelatedI am looking for a how to configure a DHCP server for a Cisco SMB 300 series switch to obtain an automatic configuration. Currently i am using a Cisco 1800 router as my DHCP server and the DHCP pool serving the 300 series switch is configured as follows.
ip dhcp pool Cisco_SMB_300
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
[Code]......
Looking at pcaps, I don't even see a tftp request going the server after the switch obtains an IP via DHCP. The config file format is exactly as obtained from the download backup section (pretty sure its not the issue since i don't see a download attempt). Also, the SMB switch is running the latest firmware image (1.1.1.8)
Looking though the admin guide i did not see specifics on how the DHCP server was to be configure for the auto configuration feature to work.
I have a question in regards to configuration I'm planning to implement. I currently have 2 x 3750 running in a stack. I would like to add 1 x 870 router connected to both switches.It's important for me that 870 is always available (it will only be used as a backdoor for our management network through WAN) but I don't want it to participate in any switching (including switching for management network unless it's going through this backdoor WAN). Do I need to configure spanning tree on all switches or stack is automaticly working as a 1 logical unit?As router is only using 100MB/s connection, how I can prevent this router from switching packets with other switches?
View 6 Replies View RelatedI have a pair of ACE 4710 and I think I have all the failover configured correctly and it all appears to be working. My question is regarding setting QOS on the physical interfaces that are part of my port channel. I have qos trust cos enabled on all the interfaces in my port channel. These interfaces are connected to a 3750 swith. Do I need to configure QOS on the 3750 to allow the COS bit to pass through my 3750 to my peer?
View 3 Replies View Relatedconfigure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies View RelatedI have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View Related