Cisco Switches :: Configure Vlan With SG 300-10P And SA 520
Apr 20, 2011
I bought for a little office a SA520 Security appliance (for future VPN with another distant office) and a SG 300-10P switch for connect 3 PC and 3 IP PHONE. THe SA 520 is the router. I must configure 2 VLANs on the switch :
VLAN2 : DATA (for PC)
VLAN3 : VOICE (for IP PHONE)
VLAN1 : DEFAULT.
How can i simply configure all ports ? I would like to configure ports 1-4 on VLAN2 and ports 5-8 on VLAN3 and port G10 is reserved for the router SA520. I want to divise network DATA/VOICE.
I think i must create a trunk on G10 for SA520 ...
View 2 Replies
ADVERTISEMENT
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Feb 19, 2013
i purchased 300-28 how it config for stp and trunk
View 2 Replies
View Related
Apr 14, 2013
I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies
View Related
Mar 22, 2012
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies
View Related
Jun 9, 2010
Just got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
View 2 Replies
View Related
Feb 15, 2012
I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
View 1 Replies
View Related
Mar 22, 2011
how to configure VLAN on ALLIED TELESYN AT 8024M?
View 1 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Apr 6, 2013
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...
View 4 Replies
View Related
Oct 6, 2011
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Dec 2, 2012
I have a customer who is on thr 192.168.254.x subnet and is using a Cisco 881 as their gateway.
They wish to create a second VLAN for the 192.168.253.x subnet.
The Cisco has Dialer0 configured for an ADSL connection.
I have partly configured the router but need some info regarding router a device on the 192.168.253.x subnet to the internet.
configure routing to the internet on the new VLAN and assist in setting up a DHCP server on that vlan. I have attached a copy of the current config.
View 6 Replies
View Related
Apr 22, 2013
Actually I am new to this ASR , in my environment my 6513 is connected ASR , I want to know how can we access and configure VLAN on Gigabit interface which is connected to 6513.
View 9 Replies
View Related
Oct 18, 2012
How to configure internet access for different VLANs in cisco 3750 switc,ISP connection directly connecting to 3750 ,3750 have 18 VLANs
View 9 Replies
View Related
Nov 1, 2011
I have a Cisco 6509 connected (gig3/17) to a Cisco 3560 G switch (Gig 0/28). The 3560 switch Gig 0/26)is connected to a distribution switch on another network. The ip address on my 6500 is 10.120.11.244 255.255.252.0 and the ip address on my 3560 is 10.120.11.211. The ip address given to me by the other network is 10.162.20.10 255.255.255.252. How do I configure the new vlan in this situation and the ip address given to me.
View 4 Replies
View Related
Feb 26, 2013
I have a WAP321 I am trying to set up. It's connected to gi1/23 and the switch system mode is set to router. The rest of the network works just fine.I have an SG500-28p and the port. [code] On the WAP321 wizard, configured IP address on my management vlan and also configured the default SSID on that vlan. That works. (I plan to remove that one) Then I add the two SSIDs for vlan 20 and 22 (private and public access) and I can't associate to either of the two additional SSIDs. I haven't configured any other settings beyond the wizard and adding the other two SSIDs. I do want cisco mobile ios (jabber) to work on the private network and also do have a couple spa525g2s that need to connect wireless.
View 1 Replies
View Related
Mar 13, 2013
I have 2960 cisco switch. I want to configure private vlan. But it is not getting configured in cisco 2960. Is there any other way to configure that in switch.
View 1 Replies
View Related
Apr 17, 2011
I would like to configure a guest-vlan and restricted-vlan on a 2960 switch, but I can not.
I am trying to configure the interface using the following commands: [code] similar result is obtained while trying to configure a auth-fail vlan. the full configuration file is attached.
View 4 Replies
View Related
Jan 20, 2013
I have hybrid network in which I want to configure VLAN on Cisco 2960 S switch. I have unmanged switch where my DHCP server and other servers are connected. Now I created two VLANs on cisco 2960S and they don't talk each other, but as soon as I connect unmanaged switch to 2960S switch, both VLANs start communicating which I don't want. I want to listen server traffic from unmanaged switch from both VLANs but simultaneously I don't want to communication between two VLANs.
View 10 Replies
View Related
Jun 25, 2012
I have 3750 series with GIBICs ports I want to create 10 vlans with its sub-net and enable all vlans to access internet.
View 4 Replies
View Related
Jan 29, 2012
We have Nexus 7k running as my core with a 6500 manageing my server farm and IP services servers (call manager, IPTV ...)My edge switch are 4500s. We currently have RIP2 running between and the switchs and each 4500 is managing its own VLANs.The IPTV uses IGMP snooping and multicasting to broadcast the video feed. The problem that came up is that the we cannot configure a gatewar for the setup boxs for the IPTV system. They will only work on a single VLAN and they are spread all over the network.Can we configure only this VLAN to be propagated over our RIP network???
View 2 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Mar 24, 2011
I have a PIX-515E that I'm trying to configure for what I thought would be a simple task. I've been playing with VMWare ESXi on a Dell PowerEdge 1850 in a lab environment. The server's IPMI is bound to one of its two physical interfaces, which I've connected to Ethernet 1 on the firewall. The interface has the following configuration:
PIX Version 7.2(4)!interface Ethernet1 nameif FrontEnd security-level 40 no ip address!interface Ethernet1.2 vlan 2 nameif IPMI security-level 90 ip address 172.16.0.161 255.255.255.224
The server's baseboard manager has been configured to tag its traffic on VLAN 2, priority left at 0 (default), and its IP address appears in the firewall's ARP cache; however, here's what I get for a ping response: Sending 5, 100-byte ICMP Echos to 172.16.0.164, timeout is 2 seconds:?????Success rate is 0 percent (0/5)
View 1 Replies
View Related
Jun 10, 2012
how to configure vlan tag on routed layer 3 interface in cisco 3945 device?
View 2 Replies
View Related
Jan 20, 2012
My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
View 2 Replies
View Related
Dec 20, 2012
My architecture is the same as show on the link with some difference.I use the router 1841 for inetrnet connexion instead of 7200VXR, this router 1841 is connected on the catalyst 3750 port G1/0/1.I use catalyst 2960 instead of catalyst 2950 or 2948.I use ASA 5510 for conexion on remote branche(I have 5 remote site), This ASA is connected on the catalyst 3750 port G1/0/37
Result of the test:
-I can ping devices in the same Vlans
-I can ping devices in different VLANs
-I can ping all device from the catalyst 3750
I cannot ping the router 1841 or ASA 5510 from the any devices (computer)The gateway of each computer is the correpondant VLAN IP address configured on the catalyst 3750.Why I cannot ping the router 1841 or ASA 5510 from the any devices (computer)
View 19 Replies
View Related
Oct 29, 2011
I'm trying to set up VLANs in my network.So the first device after the internet cloud is my ISP modem/router. I don't really use the router part. The second device is my Linksys WRT54G router with DD-WRT firmware on it.Between the two, there is a subnet just for them. After the DD-WRT router, there is a subnet for my LAN.The third device is my netgear GS108T switch (with vlan support) to which almost all my computers are hooked up. One of those computers is my server that is domain controller and has the roles as shown in the image. What I would like to do is to create several virtual machines in Hyper-V. The trick is that I want to isolate them from the rest of my network. They should be able to access (and be accessed) from the internet but not the rest of my network. So my whole network should be in the same VLAN but each VM should be individually in separate VLANs.
1) I've allready created the VLANs on my Netgear Switch. I know my DD-WRT also has VLAN support. Do I need to create the same VLANs on that also?
2) How to configure the VLAN part of the Hyper-V server? (by the way, my server OS is Windows Server 2008 R2 with the hyper-v role, it's not the bare-metal hyper-v)Should my Virtual Switch be in VLAN 10 and my VMs in the other VLANs?Should the port (on the netgear switch) in which my server is connected, be in VLAN 10 (so that my server is accessible from every other computer in the network)?
View 6 Replies
View Related
Sep 13, 2012
I am tryıng to confıgure port base Vlan on 3com S7900E switch. There are already 9 of them confıgured but one is missing and I need to add 1 more. I have done this on cisco routers but cant get my head around 3com commands.
View 1 Replies
View Related
Apr 18, 2013
I'm trying to setup following scenario which is working with no issue on netgear switches (like GS108) but I have not been able to get it to work on Cisco SG-200 I did quite a bit of reading here on many post but nothing seems to work.
View 6 Replies
View Related
Jun 13, 2011
For test I used 2 Switch that name "ESW X" and "ESW Y" I have 2 network that I named "Network A" and "Network B" I build 2 VLAN for each network that named Vlan 2 for Network A and Vlan 3 for Network B, I don't use Vlan 1 because it's the default Vlan
Configuration ESW X:
port e1 : ACCESS PORT on UNTTAGGED Vlan 2
port e2 : ACCESS PORT on UNTTAGGED Vlan 2
port e3 : ACCESS PORT on UNTTAGGED Vlan 3
port e4 : ACCESS PORT on UNTTAGGED Vlan 3
port g3 : TRUNK PORT with UNTTAGGED Vlan 1(default) and TAGGED Vlan 2 and Vlan 3
[code]....
Each Vlan can't communicate between the two switch, I think they're a problem in my vlan/port configuration?
View 2 Replies
View Related
May 5, 2011
I need create vlans in Cisco SF 300-24 Switch.Ports 1 to 6 are available for other ports (from 7 to 24).For examples: port 7 is available for ports from 1 to 6 but is not available for ports from 8 to 24,port 8 is available for ports from 1 to 6 but is not available for ports from 9 to 24 and 7, port 9 is available for ports from 1 to 6 but is not available for ports from 10 to 24 and 7 and 8,.....(to port 24).
View 7 Replies
View Related
