Cisco Firewall :: PIX 515E - Configure Vlan Connection To Dell Server?
Mar 24, 2011
I have a PIX-515E that I'm trying to configure for what I thought would be a simple task. I've been playing with VMWare ESXi on a Dell PowerEdge 1850 in a lab environment. The server's IPMI is bound to one of its two physical interfaces, which I've connected to Ethernet 1 on the firewall. The interface has the following configuration:
PIX Version 7.2(4)!interface Ethernet1 nameif FrontEnd security-level 40 no ip address!interface Ethernet1.2 vlan 2 nameif IPMI security-level 90 ip address 172.16.0.161 255.255.255.224
The server's baseboard manager has been configured to tag its traffic on VLAN 2, priority left at 0 (default), and its IP address appears in the firewall's ARP cache; however, here's what I get for a ping response: Sending 5, 100-byte ICMP Echos to 172.16.0.164, timeout is 2 seconds:?????Success rate is 0 percent (0/5)
View 1 Replies
ADVERTISEMENT
Jan 3, 2012
I have a PIX 515e (8.0 (2)) and 1841 router (12.4(25)).I had the following setup working without issue:
[Internet] <-----> PIX <-----> 1841 <-----> [LAN]
I then tried to introduce VLANs and now I can not reach the Internet from the LAN. It seems that no nat translations are taking place.
-I can successfully ping the LAN from the PIX.
-I can successfully ping the Internet from the PIX.
-I can successfully ping the PIX inside_lan interface from the router
-I can not ping the outside interface from the router
-I can not ping the Internet from the router
I introduced the LAN side VLAN first and everything still worked. However, once i introduced the VLAN between the router and PIX, things have broken down. [code]
View 2 Replies
View Related
Oct 2, 2012
We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies
View Related
Feb 28, 2011
I recently upgraded my Pix 515e from 6.3 to 7.08. Upgraded pmd to adsm. If I do a show ver, it states 7.08. But, if I do show config, it still shows 6.3.Why would they be different? Since adsm runs fine, I know that the upgrade went fine.
View 2 Replies
View Related
Dec 5, 2010
How can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
ADSL Modem ---> Firewall --> Switch--> Computers
View 2 Replies
View Related
Jul 3, 2011
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it.
I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
View 5 Replies
View Related
Oct 2, 2012
Is there a way to configure a DHCP server for my internal subnet of 192.168.20.1 which is on a 3550 layer 3 switch from my 5505 ASA Firewall.My subnet of 10.1.1.0/30 is connecting my 5505 to 3550. All I'm trying to do is run a DHCP server down to my hosts. The only options on ASA 5505 is
dhcpd address 192.168.20.1 - 192.168.20.254 outside or inside, which conflicts with my subnet of 10.1.1.0 used to connect my internal subnet of 192.168.20.1 for the whole network.
When I used my router it did not need the (inside, outside) keywords and just an ip helper-address command. How do I configure my my firewall DHCP server to propagate the 192.168.20.0 network through my 10.1.1.0 connection.
View 3 Replies
View Related
Aug 22, 2011
I need to redo the configuration on the new one?
View 11 Replies
View Related
Sep 17, 2011
i got an error while connecting to my PIX (515e) via ssh connection there is an error message appears (The server has disconnected with error, server message reads: Internal Error) and at the console session at the time time, the following message appears also (process_create: out of memory)
View 1 Replies
View Related
Apr 2, 2011
Currently, my customer has 2 units of Cisco PIX 515E running on Active/Standby mode. As for the heartbeat link, there are 2 dedicated switches placed in between both the Cisco PIX 515E i.e. FW1 --> SW1 --> SW2 --> FW2.
My customer will be changing both the Cisco PIX 515E to Cisco ASA 5510. Now, they are asking me, since they will be using Cisco ASA 5510 eventually, can the heartbeat link be a direct UTP cross cable or must the 2 switches in between still exist?
I remember I have tested this before, few years back, in the event I were to pull out the UTP cross cable that's connecting both the Cisco ASA 5510 Firewalls directly (without any switches in between), the Active/Standby mode still works fine. It doesn't go bad whereby both the Cisco ASA 5510 suddenly becomes Active/Active, and causes network issue.
Are switches required for the heartbeat link in a Cisco ASA environment or can a direct UTP cross cable connection be adequate.
View 3 Replies
View Related
Oct 29, 2011
I'm trying to set up VLANs in my network.So the first device after the internet cloud is my ISP modem/router. I don't really use the router part. The second device is my Linksys WRT54G router with DD-WRT firmware on it.Between the two, there is a subnet just for them. After the DD-WRT router, there is a subnet for my LAN.The third device is my netgear GS108T switch (with vlan support) to which almost all my computers are hooked up. One of those computers is my server that is domain controller and has the roles as shown in the image. What I would like to do is to create several virtual machines in Hyper-V. The trick is that I want to isolate them from the rest of my network. They should be able to access (and be accessed) from the internet but not the rest of my network. So my whole network should be in the same VLAN but each VM should be individually in separate VLANs.
1) I've allready created the VLANs on my Netgear Switch. I know my DD-WRT also has VLAN support. Do I need to create the same VLANs on that also?
2) How to configure the VLAN part of the Hyper-V server? (by the way, my server OS is Windows Server 2008 R2 with the hyper-v role, it's not the bare-metal hyper-v)Should my Virtual Switch be in VLAN 10 and my VMs in the other VLANs?Should the port (on the netgear switch) in which my server is connected, be in VLAN 10 (so that my server is accessible from every other computer in the network)?
View 6 Replies
View Related
Jan 20, 2012
My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
View 2 Replies
View Related
Aug 1, 2012
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
View 2 Replies
View Related
Nov 15, 2011
I want to configure my Cisco asa 5505 as a dns server, so that when i configure any of my network systems ip address and use my firewall as a default gateway and dns ip, the system should be able to browse internet.
View 5 Replies
View Related
May 5, 2013
We have one Cisco ASA5515 firewall, I configured ftp mode to passive, inspect ftp in service, use anoother public to do NAT with ftp server, and also configued ACL in outside interface, but I failed to access the ftp server from internet use that public ip address, no problem to acces the ftp server use its inside address in LAN.
View 9 Replies
View Related
May 24, 2011
How can i connect my dell dimension 4550 desktop from a hawking extender router to my ethernet port on my dell. what settings must i change if i were using a wireless before this
View 1 Replies
View Related
Oct 13, 2011
I am using a fiber optic connection. I want to connect it directly to ASA5510. A WLC2504 will be connected to ASA and one Aironet AP will be deployed at first. (At this moment I am not using any Windows server but in near future I will need to deploy Windows Server 2003 in my corporate network) My questions are:
Can I configure ASA as DHCP server for my LAN?
Can I configure WLC as DHCP server for my LAN?
If we can configure both then what is the best practice from above two options? (I am new to Cisco stuff and first time user)
View 1 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Oct 3, 2006
My lap top and pc were both accessing internet fine. Now my laptop has the message windows cannot config. wireless connection. If you have enabled another prog. to manage this connection use that software. Then it says ifI want windows to config., start WZC service. I am a novice and don't understand any of this. I don't think I have done anything to enable another prog to manage the connection. I have tried reloading isp disc and making new network connection but to no avail. the little network logo has a red x constantly.
View 4 Replies
View Related
Jan 25, 2012
I am trying to change the DNS server that my VPN gives to VPN clients on a Cisco PIX 515E. What command will change it from 10.6.0.2 to 10.6.0.4? The software version is 7.2(3)
View 3 Replies
View Related
Dec 23, 2011
Currently I have an ASA setup as a Firewall with 1 outside interface and 2 inside interfaces. Initially, the Guest interface was setup to receive DHCP from the ASA and everything was working. I'm adding router and a server for the guest interface and what I'm trying to accomplish now is the following: ASA 5505 > Airport Extreme with a public static IP (69.xx.xx.6), handling DHCP and NAT > Mac Server as DNS Server.Right now, when I connect to my Airport Extreme with any computer, I don't have internet. I don't understand what's wrong. My DNS Server has a reserved IP address: 192.168.226.2 and it's pointing to itself and forwarding the ISP DNS servers, the Airport Extreme is handling the DNS Server IP and the ISP DNS Server IP but I can't connect to the internet from the server. [code]
View 31 Replies
View Related
May 9, 2012
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies
View Related
Jan 27, 2013
I am wondering if this is possible. We have multiple internet connections with fixed IP's coming into the office. We'd like to use one for FTP backup and another to service our websites. From what i have read a 5510 doesn't do policy based routing, but we'd like to configure our ftp server to use one of the internet pipes and our webserver to use another internet pipe. Is that possible?
We'd have two outside fixed IP interfaces and two internal interfaces. I could then use one of the internal interfaces for the web server and the other for the FTP server. consequently if the internal web server and FTP server use the fixed IP"s corresponding DNS server wouldn't that effectively route all FTP traffic out one interface and all web traffic out the other?
Then the FTP traffic would be NAT'ed to an internal interface and the HTTP & HTTPS traffic would be NAT'ed to a separate internal interface.
Then if each of the internal servers used the corresponding internal NIC on the ASA as it's gateway and the fixed IP's that correspond to the external DNS server, then it would affectively only use that gatway out for traffic? Would that work? Does it should route traffic out those pipes correct? Will the asa support two different next hop routers for the two different interfaces?
View 2 Replies
View Related
Aug 28, 2011
How to put two vpngroup vpnadmin dns-server addresses on a PIX 515E? I am trying to set up a second DNS Server and without the command in the PIX my VPN clients cannot authenticate through the PIX on the second DNS Server. I have tried several times to put the command in but it keeps removing the existing one and replacing it with the one I try to put in.
View 3 Replies
View Related
Jan 27, 2011
i am trying to find out if it is possible to have a translation rule fail over to a second server if the primary is down on my cisco pix515e.so for instance having an external ip address of 82.x.x.x mapped to an internal ip of 10.x.x.1
If 10.x.x.1 is down then 82.x.x.x should be mapped to 10.x.x.2.The reason i am asking this is i also have 2 css11501 load balancers and would like to have our staging servers primarily sat on one with secondary connectioin to second, production on the other failing over to each other if one is down. The load balancers will be connected to different ports on the same firewall.
View 1 Replies
View Related
Jun 13, 2012
I have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
View 1 Replies
View Related
Jan 16, 2013
Ive got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
View 8 Replies
View Related
Nov 25, 2012
I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....
View 1 Replies
View Related
May 20, 2013
I have Pix firewall 515e on inside interface its has configured with IP 192.168.0.254.And Global Nating is configured.
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.255.0 0 0
I want i configured Global nating only for only specific IP address E.g 192.168.0.0-192.168.0.30 and 192.168.0.200-192.168.0.254?How i do this?
View 13 Replies
View Related
Jun 24, 2012
how to configure a router 2900 to support connection from 2 firewall ( Active Standby connections) How can i said the router to send the traffic to the stand by when it go down the active Firewall?I was planning to use a Switch ( layer 2 capacity only) in the middle of the equipments ( between the firewalls and the router) in order to send always the traffic for 1 physical interface from the router side , and manage to route all the internatl traffic to the virtual IP of both Firewalls.Also i dont know yet how to configure a VPN site to site if i have that scheme and some Publics NAT ( Firewall - Switch - Router ), i was planning to configure a NAT in the Router in order to allow the VPN traffic to internal IP of the Firewall but still dont know if it will work.
View 2 Replies
View Related
Nov 20, 2011
I am now going to configure IPSec VPN connection for Cisco ASA 5505 (Version 8.4)
View 3 Replies
View Related
Oct 6, 2012
I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
View 11 Replies
View Related
Aug 30, 2011
I'm trying to learn Cisco ASA IOS commands, I have bought myself a 5505 ASA for my home network and plan to implement it. How best to configure it.
I have attached a diagram of how I want my network to look. The internet connection is via the Virgin Media cable modem.
View 7 Replies
View Related
