I recently upgraded my Pix 515e from 6.3 to 7.08. Upgraded pmd to adsm. If I do a show ver, it states 7.08. But, if I do show config, it still shows 6.3.Why would they be different? Since adsm runs fine, I know that the upgrade went fine.
View 2 RepliesWe just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedHow can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
ADSL Modem ---> Firewall --> Switch--> Computers
I have a PIX-515E that I'm trying to configure for what I thought would be a simple task. I've been playing with VMWare ESXi on a Dell PowerEdge 1850 in a lab environment. The server's IPMI is bound to one of its two physical interfaces, which I've connected to Ethernet 1 on the firewall. The interface has the following configuration:
PIX Version 7.2(4)!interface Ethernet1 nameif FrontEnd security-level 40 no ip address!interface Ethernet1.2 vlan 2 nameif IPMI security-level 90 ip address 172.16.0.161 255.255.255.224
The server's baseboard manager has been configured to tag its traffic on VLAN 2, priority left at 0 (default), and its IP address appears in the firewall's ARP cache; however, here's what I get for a ping response: Sending 5, 100-byte ICMP Echos to 172.16.0.164, timeout is 2 seconds:?????Success rate is 0 percent (0/5)
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it.
I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
I need to redo the configuration on the new one?
View 11 Replies View RelatedI cannot logon with adsm anymore.when I run adsm, I type in my pw, and the screen keeps displaying "contacting the device". No timeout, just stays this way.I've updated the java version, no luck.I can connect with SSH with no problem. device = asa5550, 8.2(1) asdm 6.2(1) [code]
notice that there is no "with cookie-based authentication" here -- is this relevant?
Rebooting the device is not really an option.
i'm having issues with ASDM 6.3 on my ASA 5500.When i try to add a policy under firewall --> service policy rules (Add Service Policy Rule Wizard - Rule Actions), i'm not able to add a netflow policy as I'm not presented with a dialogue box after I press "add".i've tried this from multiple computers mac os and windows.
View 9 Replies View RelatedI am running into a issue that I cannot seem to figure out. I have a asa 5505 with the Security Plus license. I setup a native vlan where all of my network devices sit on. ie my Wireless Access point has an ip of 192.168.3.2, my switch .3. I have no issues managing these devices from any vlan I am on (permitting firewall access rules). When I try to access my ASA via ASDM/SSH. I have to use the gateway of the vlan I am on. For instance. If I am on vlan 10 I have to use 192.168.10.1 for access, if I am on vlan 20 I type 20.1...etc...etc If I type in 192.168.3.1 I get an error in the ASDM logs that states TCP reset by appliance. This is for any gateway I type except for the gateway of the vlan that I am connected to. I am posting a sanitized config. How can I configure the ASA to permit access via any gateway.
View 3 Replies View RelatedI am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
Trying to get port forwarding going using ASDM 6.4 on a Cisco 5510
I want to forward port 25/Smtp to 192.168.1.10
I have added all the rules as outlined in the link below. [URL]
But when running an open port checker on [URL]
It says the port is closed, I have noticed that under Access Rules under the Hits columns it says 52 ?
I am trying to unravel a ASA 5550 config that has been created over several years, by multiple people, some who used ADSM, some who used CLI.
None of them ever removed any lines from the configuration, and none did any documentation. When examining the actual configuration from a CLI perspective:
1. Does an ADSM- created access list end with any specific ADSM- added suffix?
2. When ANY access list is created in an ASA 5550, does it HAVE to be included in the access-group command to be functional? Can it also be functional if referenced in a "nat" command?
3. If the access list does meet either of the criteria specified in question #2, is it completely non-functional?
4. If an access list is applied to a logical or physical port that is shut down, is the access list functional?
I have just logged into the ASDM for my 5520 and can see under the "Firewall Dashboard" tab that I can enable these graphs/stats, why would they be disabled? So I was wondering if I enable these and they use alot of memory how can I disable them again?
View 3 Replies View RelatedI have just logged into the ASDM for my 5520 and can see under the "Firewall Dashboard" tab that I can enable these graphs/stats, why would they be disabled? So I was wondering if I enable these and they use alot of memory how can I disable them again?
View 1 Replies View RelatedI'm having a cow of a time trying to implement a NAT configuration after having upgraded our ASA5510 recently from IOS 8.2 to 8.4. The upgrade went fine, however we now have a need to add a new NAT rule and I'm not sure whether it's possible.
The upgraded NAT rule and access list works fine at allowing external access to a web server.
However we now need to NAT the SOURCE address (either to a pool or single address) of incoming http requests before forwarding the request to the server. Hence the server will see all requests as originating from a pool with a route heading back to the ASA. The basic issue is that the severs default gateway does not return to the ASA, so "tagging" the source address of external requests to an address or interface associated with the ASA should allow the server to return the traffic to the ASA. I know we shouldn't be doing it this way but we can't see any alternative.
Having read a huge amount of examples we can access the server with the above config (or Object NAT), and we can NAT incoming traffic,however we can't combine the two by having all external http requests Source Natted before forwarding to the server.
Is the 5512 able to be field upgraded to a 5515 and so on through 5555? I.E. Can I add ram and other hardware to make the boxes more powerful as my requirements increase? I was hoping this would have been a new feature with the ngen firewalls.
View 3 Replies View RelatedI have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
View 1 Replies View RelatedIve got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....
I have Pix firewall 515e on inside interface its has configured with IP 192.168.0.254.And Global Nating is configured.
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.255.0 0 0
I want i configured Global nating only for only specific IP address E.g 192.168.0.0-192.168.0.30 and 192.168.0.200-192.168.0.254?How i do this?
I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies View RelatedI have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
[Code].....
\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedI have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
View 1 Replies View RelatedI need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
View 1 Replies View RelatedI have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
View 6 Replies View RelatedWhat would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.
View 1 Replies View RelatedI'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
View 7 Replies View RelatedI have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
I have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
View 7 Replies View RelatedWhat would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.