Cisco Switches :: How To Configure IP Phones (SPA502G)
Dec 18, 2011
I have a question regard to switch SFE2010P, i have 2 vlan ( data and voice) and we want to configure Ip phones SPA502G, the question here is how can i make to suport 2 vlans on the same switch port, like the catalyst IOS switch port acces vlan x and switch port voice vlan x, if i set up the switch with the voice vlan like tagged doesn't work, but if i set up the voice vlan like untagged vlan its works but the PC attached to the data port on the SPA502G doesn't work?
View 1 Replies
ADVERTISEMENT
Feb 15, 2012
I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
View 1 Replies
View Related
May 19, 2011
I am trying to configure my ACS to allow 802.11 phones to authenticate. I have searched high and low for documentation on doing this with no luck. We are using unified wireless with a mix of 5508 and wism controllers. I am able to authenticate windows devices against active directory via the acs but can't seem to get anything working with the phones.
View 3 Replies
View Related
Jul 12, 2012
Our ISP has set up a Cisco 2431-16fxs IAD (dual WAN) in one of our locations. It is used to connect the devices (PCs and SIP phones) on our LAN to internet (via 1st WAN port) and ISP's MPLS-based voip network (via 2nd WAN port).
We have 2 LAN subnets - the first subnet (PCs) requires internet access only, so it goes out via the 1st WAN port. The 2nd subnet (SIP phones) is connected the MPLS network (via 2nd WAN port).
We would like to have the SIP phones (that connects to MPLS-based network 192.168.1.x) to be able to access the internet. Is it possible to configure the IAD so that the phones are routed based on destination network; i.e. anything to 192.168.1.x via 2nd WAN port, anything else to the internet via the 1st WAN port?
View 1 Replies
View Related
Jun 14, 2011
I have a new install with 3 SF300 switches, setup as vlan 2, the switch connected directly to the 2901 router has no problems, plug in a phone and it gets an IP, but if connected to either of the two swtiches behind the first switch, they do not get an IP. I am seeing the DHCP request hitting the router, and the router sending the IP to the phone, but it never gets the IP.
*Jun 15 10:40:20.040: DHCPD: client's VPN is .
*Jun 15 10:40:20.040: DHCPD: Sending notification of DISCOVER:
*Jun 15 10:40:20.040: DHCPD: htype 1 chaddr 40f4.ecef.bded
[Code]....
All ports are setup as trunk on vlan 2 including the ports that connect the switches together. Not sure what the problem is, but they are going live tomorrow and only have 48 out of 120 phones.
View 1 Replies
View Related
May 29, 2011
PoE works fine with C 1131/1141 Access Points and C-7975 IP phone but PoE does not seem to work on 7960 Phones nor on the C-1121 Access points
All devices work properly with the Cisco power injectors or on a Cisco Cat-29XX switch
Is there a trick to make PoE work for older devices ?
View 7 Replies
View Related
Jul 14, 2011
I want to connect a 6911 IP Phone to a SG 300 switch. This is my scenario: vlan 3 data, vlan 9 voice, vlan 10 admin.I have a trunk on port 10 of the SG 300 (vlan 1 untagged, vlan 3,9,10 tagged) and it is connected to a switch 3560, this switch has all the L3 configuration of the vlans and the SG 300 switch has an IP on the admin vlan (10).Also i added the OUI of my IP phones an created an LLDP Policy. Right now I have a 7941 IP Phone working but 6911 is not working. Iam using the new version 1.1.0.73 that supports CDP.
Also I noticed that even when my PC and IP phone receive IP address they can not ping each other nor the SG 300. They only can ping the default gateway or IP addresses in diferent vlans but connected on 3560 switch.
View 5 Replies
View Related
Jun 13, 2011
I have 2 (and maybe soon 5 more) 7940G phones to add to my network, which already has a Netgear POE capable switch. I've since discovered that early Cisco POE isn't the same thing as current POE, and the switch doesn't power the phones.
I was looking at adding a Cisco SD208P 8-port switch to power the phones, but I soon discovered it only has 4 POE ports, and I'm not sure that this switch will even power the 7940G phones. And if the other 5 phones show up, I'll need two of those switches with no room for expansion on the voice network.
Will this switch power those phones?Is there another small switch available so I don't have to replace my existing switch infrastructure to get these phones to work? Or do I need to scrap the phones and get something newer that will work with the current POE standards?
View 2 Replies
View Related
Oct 22, 2012
i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues.
View 8 Replies
View Related
Aug 8, 2010
I have an ESW-500, a SPA525G (also tried 504G), Polycom IP330/670 phones, and a Switchvox (Asterisk-based IP-PBX) and CDP causes some issues.Both the SPA5xx and Polycom phones support CDP but it appears to operate differently between the phones. And, surprisingly, worst of all on the SPA's.
In short:
* Switch - CDP enabled (VLAN 100), DHCP disabled (Option 82 enabled) which is basically how it comes out of the box
* Polycom phones - CDP enabled (default)
* Cisco phones - CDP enabled (default)
* DHCP/TFTP server on port 1
* Phones on ports 7,15,19 - default as smartports for Desktop & Phone
* Switchvox on port 17 - port configured as General (not Trunk) with 1U & 100U VLANs. This was required to get Polycom phones to appear in Switchvox config
With that configuration the Polycom phones work perfectly. They appear in the switch web-GUI under CDP, they present in Switchvox and can be configured.But with that configuration although the Cisco phones appear in the CDP screen they do not get DHCP. My DHCP server can see 'DHCP Discover' messages but it just goes around in circles. Disabling CDP on the switch will allow the phone to get an IP but disabling CDP on the phone still has the same problem. When I saw "around in circles" this is what I mean....
Rcvd DHCP Discover Msg for IP 0.0.0.0, Mac 00:25:84:06:12:46 [10/08 13:51:27.031]
DHCP: proposed address 192.168.100.16 [10/08 13:51:29.000]
4064 Request 2 not processed [10/08 13:51:29.062]
Rcvd DHCP Discover Msg for IP 0.0.0.0, Mac 00:25:84:06:12:46 [10/08 13:51:30.093]
DHCP: proposed address 192.168.100.16 [10/08 13:51:31.593]
4064 Request 2 not processed [10/08 13:51:31.656]
[code]....
With the difference being there's a 'DHCP Inform Msg' which there never is from the Cisco.I have tried many options regarding DHCP Relay, DHCP Server addresses, DHCP VLAN Interfaces, smartport settings etc but with CDP enabled the Cisco phone just will not get DHCP.
View 2 Replies
View Related
Apr 10, 2012
According to the documentation, the Switches SFE2010P and SGE2010P have a maximun total power output of 360W. Using only SPA500 series IP Phones that have 10W maximun input, how many SPA500 IP Phones could be connected safely to this switches? 36 ? or 48 ?
View 1 Replies
View Related
Jan 4, 2012
I have a CUCM BE environment with a number of remote users with 8961 phones connecting to an ASA 5501 via AnyConnect. The phones register fine and can make inbound/outbound calls as well as four digit dialing to other users at the corporate site.
The problem is when a remote user tries to four digit dial another remote phone. The called phone will ring but there is dead air once answered and then the line goes dead.
This sounds like a routing issue to me. How to get AnyConnect clients to be able to reach each other?
View 3 Replies
View Related
Sep 5, 2012
I am trying to hook up a SF300 switch to a cable modem and then plug some phones into the switch that are configured with static IPs. I am able to access the switch without an issue, but need it to pass traffic from the phones to the network and it is not doing so. We cannot do trunking because we are not using BSoD modems yet (next phase). For now, we just need the switches to pass everything from the phones to the network as is. Any ideas?
View 4 Replies
View Related
Apr 15, 2013
I am new to VLANs although I generally understand the concept. I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access. My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports. I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains. Also, do I need a management VLAN??
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??
View 4 Replies
View Related
Mar 1, 2012
I have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
View 1 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Sep 6, 2011
I have a SF 300-24p.... How do I configure it to act use like a hub, with the uplink on G1... And How do you set all the ports to POE for ViOP phones, and these ip phones are going to get DHCP over network..
View 1 Replies
View Related
Apr 20, 2011
I bought for a little office a SA520 Security appliance (for future VPN with another distant office) and a SG 300-10P switch for connect 3 PC and 3 IP PHONE. THe SA 520 is the router. I must configure 2 VLANs on the switch :
VLAN2 : DATA (for PC)
VLAN3 : VOICE (for IP PHONE)
VLAN1 : DEFAULT.
How can i simply configure all ports ? I would like to configure ports 1-4 on VLAN2 and ports 5-8 on VLAN3 and port G10 is reserved for the router SA520. I want to divise network DATA/VOICE.
I think i must create a trunk on G10 for SA520 ...
View 2 Replies
View Related
Feb 12, 2013
I would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies
View Related
Feb 11, 2011
I am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies
View Related
Mar 8, 2011
I've to connect 2 building with fiber, for this I use 2 HP baseline switches.How do I have to configure the 2 switches so that i can have PC connected to switch 2 able to "talk" with the server connected to switch 1 ?
View 9 Replies
View Related
Feb 3, 2013
how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
View 3 Replies
View Related
Nov 14, 2011
our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
View 2 Replies
View Related
Feb 19, 2013
i purchased 300-28 how it config for stp and trunk
View 2 Replies
View Related
Dec 15, 2011
Is there a CLI, other than the terminal mode menu, for this switch? I would much prefer to use a CLI to configure it than the (web) menus available.
The web menus are confusing and the manual is long. I already know how to configure Cisco Switches via the CLI quite well.
View 3 Replies
View Related
Jun 22, 2011
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
View 10 Replies
View Related
Oct 26, 2011
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
View 7 Replies
View Related
Mar 30, 2011
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies
View Related
Oct 22, 2011
how do i configure cisco switch Edge
View 1 Replies
View Related
Mar 6, 2013
How config dynamic alp inspection for 300 or 500 series ? I find in admin guide it's no simple to do.
View 8 Replies
View Related
Nov 28, 2011
I am looking for a how to configure a DHCP server for a Cisco SMB 300 series switch to obtain an automatic configuration. Currently i am using a Cisco 1800 router as my DHCP server and the DHCP pool serving the 300 series switch is configured as follows.
ip dhcp pool Cisco_SMB_300
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
[Code]......
Looking at pcaps, I don't even see a tftp request going the server after the switch obtains an IP via DHCP. The config file format is exactly as obtained from the download backup section (pretty sure its not the issue since i don't see a download attempt). Also, the SMB switch is running the latest firmware image (1.1.1.8)
Looking though the admin guide i did not see specifics on how the DHCP server was to be configure for the auto configuration feature to work.
View 3 Replies
View Related
Jan 8, 2013
I have a question in regards to configuration I'm planning to implement. I currently have 2 x 3750 running in a stack. I would like to add 1 x 870 router connected to both switches.It's important for me that 870 is always available (it will only be used as a backdoor for our management network through WAN) but I don't want it to participate in any switching (including switching for management network unless it's going through this backdoor WAN). Do I need to configure spanning tree on all switches or stack is automaticly working as a 1 logical unit?As router is only using 100MB/s connection, how I can prevent this router from switching packets with other switches?
View 6 Replies
View Related
Jan 24, 2013
I have a pair of ACE 4710 and I think I have all the failover configured correctly and it all appears to be working. My question is regarding setting QOS on the physical interfaces that are part of my port channel. I have qos trust cos enabled on all the interfaces in my port channel. These interfaces are connected to a 3750 swith. Do I need to configure QOS on the 3750 to allow the COS bit to pass through my 3750 to my peer?
View 3 Replies
View Related
