Cisco WAN :: 3750 Vlan Creation Error Message
Feb 7, 2011
I have cisco switch model WS-C3750G-12S-D. It is in transparent mode. I am getting below error message when tried to create new vlan.
Proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
After deleting few unnecessary vlans, it allowed me to create.
3750#sh vtp statusVTP Version : running VTP1 (VTP2 capable)Configuration Revision : 0Maximum VLANs supported locally : 1005Number of existing VLANs : 959VTP Operating Mode : TransparentVTP Domain Name : VTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0xBC 0xA7 0xEC 0xDE 0x36 0x6C 0x61 0xB4 Configuration last modified by 97.193.17.172 at 0-0-00 00:00:00
I confused with terms 'maximum supported vlans' and 'maximum locally supported vlans'. If switch is supporting vlans 1-4094 means it should also allow to create locally. Otherwise how they will pass through the switch trunks without local creation.
View 1 Replies
ADVERTISEMENT
Sep 15, 2012
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
View 2 Replies
View Related
Aug 28, 2011
I am using 3750 ME switch and we have restarted the switch 7 weeks age and we are getting error message, we are using MPLS / BGP in this switch.
View 1 Replies
View Related
Jan 6, 2013
Have a small stack of two 3750 routers. Get the following error message every few secounds:
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
Now I replaced the stacking cables but no joy. It was ok for an hr or so but then the error messages popped up again. Also random links on this stack back to access layer user switches have been going up and down randomly. So I have decided to take the next step and upgrade the IOS.
Although when I try and copy a new IOS I get the following error:
%Error writing flash:/c3750-ipservicesk9-mz.122-55.SE6.bin (No space left on device)
Seems this image is 130MB while the image that is currently on it is 74MB and free space is 54MB. How do I get the image onto the router? If I delete the current image from flash will that cause the router to stop functioning?
Also I noticed there seems to be more than one flash directory. See below:
copy tftp: ?
flash1: Copy to flash1: file system
flash2: Copy to flash2: file system
flash: Copy to flash: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
running-config Update (merge with) current system configuration
startup-config Copy to startup configuration
system: Copy to system: file system
vb: Copy to vb: file system
The current router image seems to be in flash1 and flash 2 also. Could I delete the image from flash1. Upload it there and then boot the router from flash1?
View 16 Replies
View Related
Aug 27, 2012
I am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
View 3 Replies
View Related
Aug 1, 2012
Two Vlans (ID1 and 100)are on a Cat 4500, which connects to an ASA, interface DMZ. On 4500, there is default route point to the ASA DMZ interface Issue, server on vlan 100 cannot ping a server on Vlan 1, vice verse. When I enable the realtime log, it gives me a “Translation creation failed” message, please see the attached files.
View 1 Replies
View Related
Oct 11, 2011
How do you create a vlan? In enable mode, there is no "vlan" command.
View 4 Replies
View Related
Aug 2, 2011
I’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
View 6 Replies
View Related
Jun 24, 2012
LMS installed on Windows 2003. Backup fais with message "Backup failed.ERROR(1297): Fatal error: Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mode.."
dbbackup.log attached.
View 9 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Feb 20, 2011
i am attaching the image which i recieved last night when i was assigning the IP but i got the error message which does not resembel to IP conflict error messsage
View 1 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Sep 5, 2012
tying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies
View Related
Dec 21, 2010
As soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message. I’ve google’d and turned up nothing so far. I assume I need to allocate more memory to this process.
%PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 312% exceeds warning level 310%
Here's a sh mem:
#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 3008A008 1758530508 647878488 1110652020 1110104020 1109994164lsmpi_io 98FEB1D0 6295088 6294120 968 968 968
View 1 Replies
View Related
Jun 6, 2012
We recently upgraded our any connect client from -2.5.3055 to -3.0.07059. This is running on a ASA HA pair running 8.4(2)8. Since the upgrade our users are seeing continual disconnects.
View 2 Replies
View Related
Sep 15, 2009
We have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.
View 2 Replies
View Related
Aug 6, 2012
Sometimes, either browsing from my computer, iPad or iPhone, I sometimes get a "can't connect to server" error, and it's not just a few forums here and there, it is a lot of them. But if I give them 5 or 10 minutes they will come. Imkmow that this isn't a normal up issue with sites servers actually being down. I thought it was a Google chrome issue, but it's been happening on safari. It hasn't started till we switched our Internet plan to 3mbps and a new router.
View 19 Replies
View Related
May 12, 2012
I keep dropping off my internet connection and getting this error.
View 11 Replies
View Related
Sep 30, 2012
After making some physical changes to my home network (which had been running for sometime without incident) my desktop machine stopped (home built MSI X58 Platinum MB) talking to the network. I get "media not connected" even though I am connected, and the connection works for any other computer I attach. I get indication of proper physical connection at both ends (router and computer ethernet port), however I get no connection and the default 169 .... IP address. It does not matter if I create a fixed IP address in the router and set the ip address of the port to correspond. I have tried all the ip resets, stack resets, remove and reinstall the network ports, etc., to no avail. Connecting directly to the cable modem did not work. I even installed a new buss ethernet card with its own drivers and I get the same 'media not connected'.
View 3 Replies
View Related
Jan 2, 2012
OS: Windows 7 Home Premium -- Service Pack 1, 64-bit
Browser: IE 9
Computer: Dell Studio 1745
I am receiving an error message window titled "Wireless Configuration" with the following message:
"OLE initialization failed. Make sure that the OLE libraries are the correct version."
I cannot find anything about updating OLE libraries in Windows 7. I have not installed any new software, and my computer is barely 2 years old. I do not find it a coinicidence that my free Dell tech support expired last month, and now I'm having issues with the Dell wireless card.
View 6 Replies
View Related
Jan 30, 2012
My laptop will not connect through my router anymore. I'm getting the message ( Cannot communicate with Primary DNS server (192.168.1.254). It works fine with an ethernet cable. I have a WII that uses the router also and I can watch a Netflix movie on it so the router seems to be working. My desktop computer is working fine through a DSL connection. The laptop is a Gateway and is running Vista.
View 14 Replies
View Related
Jul 2, 2012
I have an error when i try to generate radius accounting.
View 4 Replies
View Related
Aug 20, 2012
I am having a problem with my cisco 3660 router. I have installed a wic 2T interface card and every time i set it to "no shutdown" the interface always went down and keep getting the following message " %FECPM-2-SCCFAIL: Init of SCC2 for int 0/0 failed to do fecpm_dma_init" .
View 2 Replies
View Related
Mar 5, 2011
i have 2851 router and it is hanging when i login on it while it is hanging it gives me the following error message: [code]
View 2 Replies
View Related
Apr 29, 2013
What does this error message mean? What is wrong? Appears when adding a new One-To-One NAT rule. The first rule is OK. When I try to add a rule nr. 2, this error message occures.
View 3 Replies
View Related
Dec 19, 2011
I keep getting an error message, i've tried several things to resolve it but still no success.This is the exact error message:
regular translation creation failed for protocol 41 src Customer: dst outside:
View 4 Replies
View Related
Jan 2, 2008
I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
View 2 Replies
View Related
Jul 4, 2012
l have some problems when l try to access to the switch by telnet or ssh, by the console port , the switch show me the next message:l need restart the switch in order to access it again.
View 5 Replies
View Related
May 8, 2011
I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
I'm getting constant %C4K_S2W-4-WRITECALENDARERR: Calendar write operation Failed errors on the console. I was also getting them on the original IOS version.
Anything I've seen say's to ignore them but their very frequent filling up the logs.
There's very little return on google and no bugs to report on Cisco?
View 8 Replies
View Related
May 22, 2011
After setting thru set time command, error message is display on server 'synthetic time issued'.
View 2 Replies
View Related
Nov 19, 2012
Server Error: 550 emails blocked from send.
View 1 Replies
View Related
Sep 25, 2011
i keep getting an error message when i scan. error message: cannot communicate with scanner for these reasons
-scanner is turned off
-scanner is disconnected (it is disconnected from LAN, if using on LAN)BUT MY MACHINE IS ON
View 3 Replies
View Related
Feb 25, 2013
Sylvania Smartbook synet7wic-bk cannot get online. It shows my wifi is on, but I do not have a tab for wifi information, to put my info in it.
View 2 Replies
View Related
