MGMcc solved my set up problem with my KDL-32ex713 which (i've swapped for a new model - its a long story). I used exactly the same ip addresses for the set up on this KDL-373x524 and got messages "wireless device found, local access failed, internet access failed". As my router and pc are the same as last time why the set up doesn't work this time and what I should do?
View 2 RepliesTech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 6134 Mb
Graphics Card: Intel(R) G33/G31 Express Chipset Family, 256 Mb
Hard Drives: C: Total - 463782 MB, Free - 396406 MB; D: Total - 13154 MB, Free - 1850 MB;
Motherboard: PEGATRON CORPORATION, Benicia
Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated and Enabled
I recently bought a Sony Bravia HD TV with wireless internet capabilities.When I try to connect to my wireless internet. The TV finds our wireless router name, but when we try to finally connect wirelessly it gives the following message: TV wi-fi found, local access failed and network access failed. The router we have is a Actiontech PK500.On the TV we have three differant ways for the tv to locate the router they are by scanning, the WPS button and by entering the WPS pin. We've tried all three and got the above message.
I tired connecting my Sony TV to the internet.It wouldn't connect automatically so I manually entered
IP Address 192.168.1.200
Subnet Mask 255.255.255.0
Default Gateway 192.168.1.1
Primary DNS 192.168.1.1
Secondary DNS 0.0.0.0
When it tested that it only gave me local access but not internet access. What else can I do to fix this? I use a netgear router WPN824N.
I just bought a Sony Vaio SVS15 and all I've done is set up the OS (Win7 Pro 64bit) and thus far, have not been able to connect to the internet wirelessly. I can use the internet if I plug in the ethernet cable but it does not detect any available networks using wireless even though I can connect wirelessly using other devices. I have updated the laptop using Windows Update and downloaded the latest driver for the wireless adapter (Intel Centrino Advanced N-6235) and still have had no success. Also, I have not yet installed any kind of Anti-Virus Software.
Here is the IP Config output
C:Windowssystem32>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Sauchi-VAIO
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
Can't connect a sony vaio laptop to the internet.Says wireless association failed due to an unknown reason. My other laptop connects just fine though
View 2 Replies View RelatedNew laptop, Sony Vaio. At first it started having problems holding a wireless internet connection (kept dropping) now it won't connect at all, wirelessly.I have a Dlink DIR 625 modem which was working perfectly. I bought a new one, thinking this was the issue. Same thing happened. Contacted my ISP, they said the modem was fine (even came out to confirm). It is a Scientific Atlanta modem. Contacted Sony and their tech did a lot of R.C to my laptop and tried a number of things. They couldn't solve it, thought it was a hardware issue (loose wire in the network card) so they had me bring it out of town to be fixed. I did that, they said it wasn't hardware that it was software and that it was working in their store. I got it home and it still didn't work.To be on the safe side, I swapped out the modem and got a new one. Still not working. I followed instructions in previous forums to do a 'stack reset' and it still didn't resolve my issue.I updated the network drivers from Sony's site, disabled AVG firewall entirely and it still doesn't work. I can connect now only by hard line connection but even still it drops. [code]
View 14 Replies View RelatedI have a very annoying problem with my Linksys WRT54G2.When I connect a wireless device (laptop, phone, TV, Ipad) to my wireless network I only see a Local connection, no connection to internet. After resetting the router (power off for several seconds) the internet-connection is available again.I have to do this every 1 - 2 days.
View 7 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedI have a Sony Vaio VGNFW378D that runs with Windows Vista. Ever since I got this computer (about 2 yrs ago), I have had problems with it suddenly disconnecting from the internet. When this happens it could never detect any wireless networks and I would have to restart the computer to temporarily solve the problem. It usually happened after the computer was in hibernation.
Yesterday this happened again, only this time restarting the computer did not solve the problem. When I could not connect to a network I clicked on "Diagnose why Windows cannot find any additional networks" and it said "Install wireless networking hardware, and verify that the correct drivers are loaded".
I went onto the Sony website to download the Intel Wifi link 5100 AGN wireless LAN Driver and updates. The download was not successful and I received a message indicating that the latest updates of this driver were already installed in my computer.
Representatives at Sony only directed me to links that had steps to finding out what my problem was, which I followed with no success. Most of the steps included enabling the adapter in the device manager, uninstalling and reinstalling the driver, etc...I could not do any of these things because the driver does not appear in the device manager at all.
my network adapter can't be found. so i do i find i/
View 1 Replies View Relatedwe took one of our controllers and turned LAG on and since then it is unreachable on the WCS. The controller is running version 7.0.116.0 and the WCS is running 7.0.172.0. I can access teh WLC no problem through web interface and CLI, as I can also do this with the WCS as well, but the WCS cannot access the WLC.From CLI i can ping the WCS from the Controller and get a response, but from CLI on the WCS, I cannot ping the controller.
View 5 Replies View RelatedMy wireless internet at uni is showing up with two errors, when its connected it will come up saying that there is an ip address conflict then it will work for a short time then show this message when I try to load a webpage:The server at Google can't be found because the DNS look-up failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing*Google Chrome*from accessing the network.
View 13 Replies View RelatedAntennas were set aside prior to device installation, and now can't be found. Can they be ordered as a replacement kit?
View 3 Replies View RelatedIn Windows Vista I am able to connect to wireless router, but can't access internet due to Local message only. Have repaired network adapter , reset cable modemm unchecked version 6 of TCPIP network settings.
View 3 Replies View RelatedSometimes for a minute sometimes all day until I reset modem/router. It never says not connected though...it always says connected and excellent signal strength but when it won't access internet I can look at my modem/router and tell by the lights its not working even though it says connected. This time even though I reset everything like normal I still can't access internet. I thought it might have been my router so I went and bought a new one and still nothing. Doesn't work wireless or through local connection. Both say connected but nothing. When I do a diagnostic I get the DNS 0x2afc and HTTP 12007 errors. Both computers won't connect so I'm thinking it has to do with my actual router settings or modem.Both Windows XP and Windows 7 laptops won't work.
View 11 Replies View RelatedThis router was just purchased this past week. I have 1 laptop, 1 desktop, and 1 netbook that is connecting to this (along with various smartphones). Set it all up according to the booklet, and ran into some trouble. When connecting through wireless, I only have "Local only" on the older laptop and desktop PC, but full internet access through the smartphones and the netbook. But, when I connect through LAN with the laptop, I have internet connection (only through LAN, not wireless). I suspect this also occurs on the PC, but the two are no where near each other to attempt. I installed the latest firmware version to no avail, and had done a full reset on the router and reinstalled it.
View 1 Replies View RelatedI am facing a kind of weird problem!! My Sony Vaio was getting connected to my Home wifi network and I could access Internet without any problem. Its been few days now that I can't access Internet though it shows connected. It does connect with the Wifi without any issue and even show the full signal like before, but actually there's no internet access. No browsers (IE,Chrome,FF) load any webpage, no messengers work.
View 1 Replies View RelatedI am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
I have a WAP4410N that only allows my laptop local access, no Internet. Here is the scoop:
- Other users connect to the WAP and get Internet access
- Laptop connects to many other networks and has Internet access
- Laptop is running Vista
- ipconfig /all has address, mask, gateway, DNS, and looks normal
- Adapter is Atheros AR5007 802.11b/g with latest drivers
i have
dell 170L (old but very stable)
winxp/pro
linksys wusb54gs adaptor
installed the software and i get the "connected to the access point (very strong signal) but the internet cannot be found"this was working for quite some time and i shut the system down for quite a while before needing to set it up again.
I am not able to use bluetooth on my laptop. I am using windows7. After installing the bluetooth software, whenever i am trying to access i am getting error as "Bluetooth radio device not found"
View 1 Replies View RelatedI have some issue with internet connection and Router WRT54G. There is always "Local Connection" but no internet access. I checked that at two different laptops. One with Windows Vista and the other one with Windows XP. Both the same problem. There is a wireless connection with excellent signal strength but no internet access. I added a screen shut to see the Router setting. If more needed I will add more.
View 6 Replies View RelatedI have a Sony Vaio Laptop VGN-NS20M and have rebooted it as had a few issues with it. Now the internet drivers have disappeared from device manager. The only thing there related to the internet is under modems. Which has nothing to do with the wifi or the ethernet port.So cannot connect via wireless or the ethernet. Seems strange both have failed. There is no ? or yellow! there, as there is no devices there.I have tried the drivers from the Sony website but they just do nothing, and the troubleshooting from the network icon just says Windows cannot find a driver for your network adapter.Its a dual boot laptop with Vista and Win7 and have the same issues on both OS.
View 12 Replies View RelatedI am trying to install Cisco Connect for my E1000 but I get the following error each attempt "An HNAP Call to the device failed for unknown reasons" I've already updated the router to 2.1 version of the Firmware.
Full Details
Error code: 82BD0305Error description: An HNAP call to the device failed for an unknown reason.Model name: unknownModel number: E1000Serial number: unknownFirmware version: unknownOperating system: Windows 7 SP 1Software version: 1.3.11069.2Connection type (WAN): unknownIP address (LAN): unknownIP address (WAN): unknownComputer IP address: 192.168.1.132
I HAVE A 3 YEAR OLD DELL STUDIm O 1747 (YEP IT WAYS A TON), AND AFTER I start up the ole computer and Icon comes on a bit later in the desktop tray that says "mobile broad band not found. I am quite sure it came with the Original Operating system (windows 7). and I have been considering reinstalling the operating system provided by Dell which I still have for Windows 7....Which is a hasslel the last resort...I tried doing a recovery on the system but I will be damed if I can remember the password even though the computer boots up and I get my display window every time..
View 4 Replies View RelatedMy WLAN has been working fine for the past 6 months. Recently it started connecting and disconnecting itself. ANd now it will only connect to the network but wont give internet access. I can connect to the same router using an ethernet cord. And I can connect to the wireless network using my phone or other computer. There are no driver updates for my network adapter, and I tried reconfiguring the router. That worked for a short period of time, but now I have the same issue. I tried a system restore back to before a recent virus software update to see if maybe that update was causing the firewall to block something.
View 14 Replies View RelatedNetwork Adapter not found on Device manager in normal mode, when in safe mode it shows the Network Adapters
View 1 Replies View RelatedI have a E6410, install sim card, load and start Mobile Broadband Manager and it say me an error "Mobile Broadband Device not found"
I already download and install Wirless Mobile Broadband Drivers, both of them (5620 and 5540 mini card) i realy dont understand how to determine which of them installed in my laptop.
My WRT310N linksys wireless router has recently stopped permitting internet access to devices connected to it, both wired and wirelessly. I have connected my broadband modem directly to a single computer (which is how I am posting this) and evidently there is nothing wrong with my internet service. I have tried restarting my modem, the router, and the computers I am trying to access the internet with, and it has not worked. Note that local communications work fine, I was able to ping another device connected to the router, and even establish a TCP connection.It is possible that the settings on the router have been changed without my knowledge, if so, however, I do not know which setting could be causing this.
View 1 Replies View RelatedWe have configured following commands on switch to fallback to local Vlan if both radius server (policy persona's) is found dead. For test purpose we shutdown both servers (policy persona's) but fallback didn't work. We have 3750 switch running image 12.2(55)SE6 having following configuration.We do not know whether we configured switch in proper way or do we need to modify it. [code]
View 5 Replies View RelatedAbruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies View RelatedI use a hardwired Ethernet adapter to connect to the internet from home. I cannot connect to the internet on the N5110 but can connect on my desktop PC. I look at the hardware device manager and cannot find an Ethernet adapter. This leads me to believe something happened to the card. It should show up in the hardware profile. I don't want to use a wireless connection. I want to use my hardwired Ethernet adapter.
How can get the system to recognize the device? I don't need to send it in for repair. There is some work I do that can only be done on this computer.