D-Link DIR-615 :: Wireless Is Local Only - LAN Has Internet Access
Dec 22, 2012
This router was just purchased this past week. I have 1 laptop, 1 desktop, and 1 netbook that is connecting to this (along with various smartphones). Set it all up according to the booklet, and ran into some trouble. When connecting through wireless, I only have "Local only" on the older laptop and desktop PC, but full internet access through the smartphones and the netbook. But, when I connect through LAN with the laptop, I have internet connection (only through LAN, not wireless). I suspect this also occurs on the PC, but the two are no where near each other to attempt. I installed the latest firmware version to no avail, and had done a full reset on the router and reinstalled it.
View 1 Replies
ADVERTISEMENT
May 14, 2013
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : V8
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : Virgin Media
I have recently purchased and installed a TL-WR841N wireless router to replace an older system. After following all of the quick install guide and the like I got it set up and working correctly both wired and wireless. However one laptop in the household, an Acer Aspire 5315 running Windows Vista 32bit, does not connect. Using an ethernet cable works fine but the wireless signal is seen and appears to connect but does not find the internet and states Local Only Access.When connected wirelessly I also cannot ping the device but when connected with a cable I can and get a good return.The firmware is up to date on the router and the latop is full up to date with drivers and windows updates.
View 2 Replies
View Related
Nov 10, 2012
I have an dir-615 h2 with upgraded firmware to 8.03 instead of the default that was 8.02, now it crashes and i cant reach the router on cable or wireless. its dead and i have to restart it to work.. where can i find the h2 8.02 firmware.
View 7 Replies
View Related
Jan 3, 2012
In Windows Vista I am able to connect to wireless router, but can't access internet due to Local message only. Have repaired network adapter , reset cable modemm unchecked version 6 of TCPIP network settings.
View 3 Replies
View Related
Jun 14, 2012
Sometimes for a minute sometimes all day until I reset modem/router. It never says not connected though...it always says connected and excellent signal strength but when it won't access internet I can look at my modem/router and tell by the lights its not working even though it says connected. This time even though I reset everything like normal I still can't access internet. I thought it might have been my router so I went and bought a new one and still nothing. Doesn't work wireless or through local connection. Both say connected but nothing. When I do a diagnostic I get the DNS 0x2afc and HTTP 12007 errors. Both computers won't connect so I'm thinking it has to do with my actual router settings or modem.Both Windows XP and Windows 7 laptops won't work.
View 11 Replies
View Related
Dec 1, 2012
Region : Argentina
Model : TL-WR741ND
Hardware Version : V4
Firmware Version : 3.13.12
ISP : Triple C
I'm trying to set up my new WR741ND router to replace the old WR541G with excctly the same cabling,ISP account etc.
All seem to be working i.e. I get the PPPoE connection against the ISP and cat ping by name to Internet addresses from THE ROUTER.Also I get DHCP handing out addresses both to my desktop connection by Ethernet cable and to my laptop via Wifi.And the computers may ping the router and also connect its admin GUI.However,the computers stop at the router and can't go further.All they can go is to the router as if it doesn't route between LAN and WAN.With the 541 router everything works and as I said it has the same setup (very basic,no static routes or anything too smart).
View 4 Replies
View Related
Jan 11, 2011
I have a WAP4410N that only allows my laptop local access, no Internet. Here is the scoop:
- Other users connect to the WAP and get Internet access
- Laptop connects to many other networks and has Internet access
- Laptop is running Vista
- ipconfig /all has address, mask, gateway, DNS, and looks normal
- Adapter is Atheros AR5007 802.11b/g with latest drivers
View 2 Replies
View Related
Sep 7, 2012
I have an EA2700 running latest firmware 1.1.38.138827. It is using Cisco Connect Cloud. I am unable to access the DHCP Reservations link under Connectivity/ Local Network. When I click on it, nothing happens. I've tried multiple browsers including IE 10 (Windows 8 RTM), Firefox 15, and Chrome 21. I also tried on a Windows 7 machine with IE 9 and the link doesn't work on that either except that it shows a box that says Invalid Character when I click on the DHCP Reservations link. I see no invalid characters on the screen. Any workaround other than downgrading the firmware or assigning static IPs on individual PCs?Also, on an unrelated note, where is the Dynanic DNS configuration on the Cisco Connect Cloud?
View 8 Replies
View Related
May 16, 2011
MGMcc solved my set up problem with my KDL-32ex713 which (i've swapped for a new model - its a long story). I used exactly the same ip addresses for the set up on this KDL-373x524 and got messages "wireless device found, local access failed, internet access failed". As my router and pc are the same as last time why the set up doesn't work this time and what I should do?
View 2 Replies
View Related
Jun 23, 2012
I have some issue with internet connection and Router WRT54G. There is always "Local Connection" but no internet access. I checked that at two different laptops. One with Windows Vista and the other one with Windows XP. Both the same problem. There is a wireless connection with excellent signal strength but no internet access. I added a screen shut to see the Router setting. If more needed I will add more.
View 6 Replies
View Related
Jun 16, 2012
I got a new TP-Link WR740N router and I'm having a problem with it. Everytime I enable security (WEP, WPA etc.) the signal on all notebooks will go "local access only" immediately, even if I use the right password. Router signal is always there, but Internet access will only be available if security is set to "unprotected" on the router setup. Funny thing is that my old router (Linksys WRT54) had WPA2 on and everything was ok.
View 4 Replies
View Related
May 18, 2011
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies
View Related
Sep 30, 2012
After I changed the router password today, I am not able to access the Internet through my machine. Seeing the 'Unidentified netwrok, access to local only'. However, other people connected to the same network are using Internet
View 14 Replies
View Related
May 14, 2011
I have a Compaq Presario Windows Vista. I currently have a Wireless router. It used to be Netgear. About 2 wks or so, my company changed it and gave me the password. I am currently connected to the one they changed to but local access only and no internet. Under Network and Sharing Center, it says: Unidentified network (Public network) Access: Local only Connection: Wireless Network Connection (perfectv) Under Internet Options, Connections , it shows the following connection: T-Mobile US Standard Modem When I try using the Windows Network Diagnostics, it keeps coming back with the options that havent worked. The options are: - Plug a cable into the network adapter Local Area Connection - Automatically get new IP settings for the network adapter Wireless Network Connection - A problem with your network router or broadband modem might be preventing an Internet connection Note: I am always able to connect to the internet wherever free wi-fi is available. If a password is required all I need is to obtain it and enter it without making any changes in the system. This is the only time Ive had issues getting online, even though I have the password.
View 5 Replies
View Related
Mar 17, 2013
If there was a workaround for me to connect to the internet outside of my citrix session? I work remotely for my company through citrix access gateway and can open/access the internet from within the session but any attempt from a browser/program outside of the session times out...I am thinking this is blocked on purpose for productivity reasons, however I want to be able to access the internet from outside of the session so that accessing personal sites for example, gmail, won't be tracked by my company.Would it be possible to run a virtual machine and change IP addresses so access within the machine runs independently of my session?
View 1 Replies
View Related
Mar 26, 2012
We've had no problems with our Internet before but yesterday I could only get local access connection. Neither my iPhone, laptop or home computer cud get any further than local connection on wireless.I'v tried the classic turnin it off and on (the router) and I'v tried connection with a cable but still gettin the same connection level! The router is a netgear if that means anything!
View 1 Replies
View Related
Jun 21, 2011
I usually acess internet on Wi-Fi, and now I have travelled, and got my laptop with me. The internet here is Local Are Connection, the one with the cable, and it says I am connected, 100 Mbps, but no internet access! I can't browse or open anything that has to do with the internet... However, It works perfectly fine on EVERY other laptop. I've searched a lot of places and I've been told to write commands like ipconfig/ all andd netsh int ip reset.log but when I do that I get "The following command was not found : int ip reset.log" I set the properties in TCP/IP to Automatically detect settings .. but nothing.
View 14 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Dec 31, 2012
I am running on Windows Vista and out of no where I cannot connect to my network %70 of the time. When I can connect I have local access and a full bar signal but no Internet access. But when I have internet access every page takes forever to load (if it even loads). I tried reinstalling my drivers and even hanged some registry stuff. My wireless card 8.11g by Broadcom.
View 3 Replies
View Related
Mar 13, 2011
What I'm trying to do is create a private network for local file sharing but also have internet access. There is a WRT54G router connected to a satellite modem in a separate building, just barely close enough to connect from my laptop, which is what sparked my original idea to use my WRT54GL as an access point.
View 1 Replies
View Related
Jan 16, 2013
I configure anyconnect vpn on cisco asa version 8.2. vpn user need to access internet so i configured split-tunnel. the split-tunnel working but i do not want to use split-tunnel for security reason. i want vpn user use our local network internet. how i do it?i think that i must do vpn user subnet nat and then what i need do additionally?
View 1 Replies
View Related
Apr 14, 2013
Installed new N600 router and every box in the house can access the internet - except for my Vista powered laptop. My network shows up as Unidentified network with 'locla only' access. Ben scouring message boards all day. Can't find a solution at Microsoft.
View 3 Replies
View Related
Mar 14, 2013
I have a Cisco ASA 5510 I am using ASDM 6.1
I have a LAN and a DMZ and an internet connection. I am using one of the internet connection IPs to host a HTTP service on a server in my DMZ. (its the same interface as my internet connenction but a different IP to the one used for internet connectivity)
so say my LAN is 192.168.1.x
and my DMZ is 172.168.1.x
I can access DMZ from Lan and vice versa. when i try to access the public IP (or URL) from a pc in my LAN i get nothing.
I have enabled DNS rewrite (doctoring) but it is still not working. the HTTP service is available from other sites.
View 1 Replies
View Related
Jun 10, 2011
I configure for our office site to site VPN project. Now I configured already Site to site vpn between ASA 5510 and 1841 router.
HQ LAN
Branch LAN 10.2.1.0/24 >>> ASA 5510>>>>> 1841 >>> INTERNET <<<<<< 1841 <<<<<< 10.30.3.0/24 ^^^^ Call Manager 2851
Now can access from Branch LAN to HQ LAN each other. I face the problems that are
1) In branch LAN , they can access HQ LAN & resource , but cannot access internet. I didn't configure NAT on PH Router
2) Can I access internet from BRANCH LAN through HQ LAN to INTERNET. Or Can I access Internet from Branch LAN from PH Router directly while access to VPN to HQ LAN ?
3) In Branch Site , hard phone cannot work but soft phone on PC can call to HQ. Hard phone IP are same in Remote Network (172.16.1.0/24 ) . Is it problem ? how can I configure separately ?
View 2 Replies
View Related
Feb 6, 2013
I've been trying to set up my new Cisco 1921 Router to provide internet access to my local network but with no success. I've been reading guides and looking at videos and I have to be missing something becaouse I can't access internet (ping/tracert) from my local network.
The DHCP server works fine and the clients on my local network gets ip-adresses from the router but can't ping or tracert outside the local network.
[code]....
View 2 Replies
View Related
Dec 12, 2012
I can make some "local policy" with client of SSL VPN AnyConnect and block access to internet?
The user would only have access to the internet if he was connected to the VPN (by internal proxy).
View 10 Replies
View Related
Mar 25, 2012
I have a DIR 655 connected to cable DSL modem RCA DHG534. I can connect to the internet through the Ethernet cable ports, but i can't access the internet via the wireless. The SSID will show up on the wireless computer(s) and Ad's. Under Control Panel, Network Connections, Internet Gateway is shown as disabled.
View 1 Replies
View Related
Mar 24, 2011
I recently went into my router and changed my security settings so that my router is WEP protected. I was having issues with somebody feeding off on my connection and causing problems with my Internet provider. I had changed it to be a secured network before but somehow it became unsecured. So, I set up an admin password and such so nobody else should be able to get into my outer . Anyway, after setting it up to with the WEP, now I cannot access the Internet from any other device except my main PC to which the router is connected.I usually get some sort of error stating that there is "limited on no connectivity" when I try to connect my laptop or Archos Home Tablet device. Yet, is reads that the signal strength is excellent and recognizes my network as existing.
View 7 Replies
View Related
Feb 22, 2011
Since I got my TP-Link 1043ND working in a previous thread I thought that my second router could be in good use at my brothers house about 50m from mine.I've got a modem in the basement, it's wired to the first router (TP-Link), the TP-Link sends wireless signals to five units, one of those units are my brothers computer. The Internet works fine on every unit.Now I thought maybe my brother will have better wireless signals to the first router if I connect a second router between. I guess the second router should be working like a switch then.I have the both routers MAC addresses. I got inside the first router and entered the WDS option, I chose LAN instead of Disabled and entered the second routers wireless MAC. Then I took the first routers MAC and entered it in the second routers WDS options MAC and Enabled it. It didn't work so I entered Static Routing Table on the second router and entered the first routers IP (started with 85.228) which I found in the dd-wrt menu. Then I entered same Netmask as the first router and the same Gateway with the interface LAN. No Internet access thou from the second router.The second routers LAN IP is set to 192.168.1.3 (the second router has 192.168.1.2 as LAN IP). DHCP is set to disabled at the second router. The funny thing is if I set the second router to the same LAN IP as the first router and the same DHCP settings with DHCP enabled it says that I have Internet Access but I can't enter the Internet
View 4 Replies
View Related
Jul 28, 2011
I am trying to setup a DIR-601 wireless router (Hardware Version: A1 Firmware Version : 1.00NA ) with my connection from Astound.I am able to connect to the internet from the cable modem (Motorola SURFboard SB5101) but I am unable to get it to work through the router. All the lights on the router look ok.When I look at the WAN status from the router setup page I see :
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Disconnected
Connection Up Time : N/A
[code]....
* I noted that the router did not show me the correct time. Is that normal ?I have even copied my laptop's MAC address but it did not work. I restarted the modem and the router a number of times but to no avail.
View 1 Replies
View Related
Aug 18, 2011
I have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
View 5 Replies
View Related
Jan 14, 2011
I have managed to get the wireless portion of my router working for the two wireless laptops in my house (one is Win XP, the other Linux) and am now trying to connect via rj45 ports + ethernet cat5e cable, my router and desktop computer that is running Windows XP. My connection type, set when I setup my wireless router, is pppoe.I have my router connected to a SpeedStream Modem, my ISP is Bell.I am worried that I will have to purchase a hub/switch in order to allow the desktop (PC3) to access the internet, although it seems to me (from reading other internet postings) that what I am attempting to do should work with just the modem+router setup that I have.I haven't worked with Windows LAN networks before (wired, not wireless) I have only dealt with my laptop's wireless internet connections and it seems much simpler to deal with than wired lan connections.
View 1 Replies
View Related
May 24, 2011
We have a D-Link DI-524 wireless router that has had no problems until today. Our laptops (with Windows XP), iPods, and iPhones all show that there is an excellent wireless network connection (as usual), but none of the computers or devices will connect to the Internet. I tried resetting, rebooting, and unplugging the modem and router. The router and modem seem to be fine. When we disconnect the router and plug the laptop directly into modem, we have Internet connection (i.e., it's not the IP).
View 4 Replies
View Related
