Cisco VPN :: ASA 5510 / 1841 - How To Configure Local Network To Access Internet
Jun 10, 2011
I configure for our office site to site VPN project. Now I configured already Site to site vpn between ASA 5510 and 1841 router.
HQ LAN
Branch LAN 10.2.1.0/24 >>> ASA 5510>>>>> 1841 >>> INTERNET <<<<<< 1841 <<<<<< 10.30.3.0/24 ^^^^ Call Manager 2851
Now can access from Branch LAN to HQ LAN each other. I face the problems that are
1) In branch LAN , they can access HQ LAN & resource , but cannot access internet. I didn't configure NAT on PH Router
2) Can I access internet from BRANCH LAN through HQ LAN to INTERNET. Or Can I access Internet from Branch LAN from PH Router directly while access to VPN to HQ LAN ?
3) In Branch Site , hard phone cannot work but soft phone on PC can call to HQ. Hard phone IP are same in Remote Network (172.16.1.0/24 ) . Is it problem ? how can I configure separately ?
View 2 Replies
ADVERTISEMENT
Mar 14, 2013
I have a Cisco ASA 5510 I am using ASDM 6.1
I have a LAN and a DMZ and an internet connection. I am using one of the internet connection IPs to host a HTTP service on a server in my DMZ. (its the same interface as my internet connenction but a different IP to the one used for internet connectivity)
so say my LAN is 192.168.1.x
and my DMZ is 172.168.1.x
I can access DMZ from Lan and vice versa. when i try to access the public IP (or URL) from a pc in my LAN i get nothing.
I have enabled DNS rewrite (doctoring) but it is still not working. the HTTP service is available from other sites.
View 1 Replies
View Related
Sep 23, 2011
I am trying to configure remote access VPN to my network, i have a Cisco ASA 5510 IOS 7.0(7).
I configured the VPN using ASDM 5.0.9 and below is the configuration received:
access-list 90 extended permit ip 192.xxx.xxx.0 255.255.255.0 192.xxx.xxx.248 255.255.255.248
access-list ClientVPN_splitTunnelAcl standard permit 192.xxx.xxx.0 255.255.255.0
ip local pool VPNIpPool 192.xxx.xxx.250-192.xxx.xxx.252 mask 255.255.255.0[code].....
View 5 Replies
View Related
Dec 9, 2012
I have to configure a default-factory firewall (ASA 5510) in a simple scenário like this image represents:At this moment i have configured the interfaces as represented above and at this moment what i want is grant access from a LAN computer (10.10.0.0/24) to the internet.
Should i configure some acl? I read that all traffic from an interface with a superior security level to other interface is allowed, so since my inside interface has a security level of 100 and the outside 0, it should be possible access to internet from an inside computer?!
From all configurations and examples i have seen around, they all contemplate a fixed IP address from the ISP, but in my scenário i have a dynamic one. This fact matter for the configuration i want to do?
My firewall is running the software version 8.2(5).
View 7 Replies
View Related
May 10, 2013
Cisco ASA 5510 and I want to configure it as an access gateway following this .[URL] the basic configuration steps on what to do on ASDM.
View 2 Replies
View Related
Jun 11, 2012
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
View 2 Replies
View Related
Jan 16, 2013
I configure anyconnect vpn on cisco asa version 8.2. vpn user need to access internet so i configured split-tunnel. the split-tunnel working but i do not want to use split-tunnel for security reason. i want vpn user use our local network internet. how i do it?i think that i must do vpn user subnet nat and then what i need do additionally?
View 1 Replies
View Related
Mar 13, 2011
What I'm trying to do is create a private network for local file sharing but also have internet access. There is a WRT54G router connected to a satellite modem in a separate building, just barely close enough to connect from my laptop, which is what sparked my original idea to use my WRT54GL as an access point.
View 1 Replies
View Related
Sep 11, 2011
I can not access the configure menu.
I try access with Serial cable blue DB09 / RJ45 on console port and serial ports on PC using putty or hyperterminal but any connection can not be done. The screen stay black and not show any text.
The computer found the port COM1 but i csn not access any information from Cisco router model 1841
View 1 Replies
View Related
Feb 6, 2013
I've been trying to set up my new Cisco 1921 Router to provide internet access to my local network but with no success. I've been reading guides and looking at videos and I have to be missing something becaouse I can't access internet (ping/tracert) from my local network.
The DHCP server works fine and the clients on my local network gets ip-adresses from the router but can't ping or tracert outside the local network.
[code]....
View 2 Replies
View Related
Apr 5, 2011
I'm trying to configure my BRI interface in "network protocol-emulate network" and "layer1-emulate network" but i don't have this second command.Is someone have allready to that with this type of interface ?I've to configure this because the ISDN line of my telco is in user mode only.
View 5 Replies
View Related
Aug 4, 2011
As per topology attached herewith, i have 2 ISPs, ISP1 and ISP2. And i have one Cisco 1841 Router with only 2 Ethernet interfaces.My Lan subnet is 192.168.1.0.My puspose is, i want to configure both ISP1 and ISP2 and my Lan Network on router, without adding any extra interaface. I also want to configure a nat so that Lan user can go to internet. I wabt to do this using 2 Interfaces.
View 17 Replies
View Related
Jul 30, 2012
I am setting up a site to site IPsec connection with a company, something which I have done many times before without trouble. I use ASDM to configure this as it is quick and painless, usually.
We have a number of other site to site connections currently configured and working fine on this ASA, these are configured with the 'Protected network - Local network' configured with the private IP's of the hosts within our network we want to make available through the seperate tunnels. This includes the configuration setting on our ASA for each connection to 'Exempt ASA side hosts from NAT'.
With this new connection however, the company has asked us to use a public IP for the host we want them to reach through the tunnel. I am not sure why but they demand it. So I added a NAT rule for the inside host, and configured the connection with the public IP under 'Local Network'. When testing to try reach a host on their side, the tunnel does not even attempt to initiate.
I cant see where I am going wrong. I am guessing the 'Exempt ASA side host from NAT' does not require to be set for this, as how else would the ASA know which internal host the public IP relates to.
View 6 Replies
View Related
May 1, 2013
I'm setting up a Cisco ASA 5510.I did the setup for my public and private interface.From the management software I can ping any outside domain using my public interface, but when I try to do that from my private interface I cannot.Also for some reason my ip phone connected to the private interface work (I'm able to make and receive call), but any computer that I connect to the private interface I cannot access the internet.
View 1 Replies
View Related
Feb 6, 2012
How do I configure a local area net work with unbounded media?
View 1 Replies
View Related
Jun 4, 2013
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
View 1 Replies
View Related
Aug 12, 2012
I am adding a second external connection to an existing system on an ASA 5510 with ASA V8.2 and ASDM 6.4. I added the new WAN using an other interface (newwan).
The intention is to route most internet traffic over the new route/interface (newwan) but keep our existing VPNs using the former interface (outside).
I used the ASDM GUI to make the changes and most of it works.ie. The default route goes via (newwan). Outgoing VPNs of a site to site nature use the previous route via (outside) as they now have static routes to achieve this.
The only problem is that incomming Remote Access Anyconnect VPNs are not working. I set the default static route to use the new interface (newwan) and the default tunneled route to be via (outside) but this is the point is goes wrong....
I can no longer ping the outside IP address from an external location. It seems the outside interface does not send traffic back to the - outside interface (or at least that's where I think the problem lies). How do I force replies to the incomming VPN remote traffic from unknown IPs to go back out on the outside interface?
The only change I need to make to get everything working on the outside interface again is to make the Default Static route use the outside interface. Which puts all the internet traffic back on the original (outside) connection.
View 6 Replies
View Related
May 18, 2011
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies
View Related
Nov 26, 2012
I'm working on setting up a couple of new WAN sites with 256K frame relay circuits back to our main building. Each new site has a new PVC, and both are pointing back to a PVC on a T1 at the main building. The main site has a 2801 with a single CSU/DSU WIC, and each new site has a 1841 with a 3560 connected to fa0/1. At both sites, I'm able to get the circuit up, and the serial interfaces at both new sites show up/up, and the subinterfaces at the main site also show up/up for both sites. Routing is being done by EIGRP, and both sites are able to establish the 2801 as an EIGRP neighbor, and I'm able to ping/tracert anywhere on our network by name or IP, so routing and DNS appear to be working. I can also ping both new routers from the main site. However, that's about all I can do. I'm not able to access any resources on our network (email/shares/internet/intranet/etc) from the two new sites. I can ping the new routers/switches from the main site, but can't ssh to them. I can ssh to them locally. There are no firewalls in the equation, and I don't think there are any ACL's in the picture either.
Can ping and tracert just fine anywhere on our network (from both the 1841, a PC plugged into the 3560, or a PC plugged directly into the fa0/1 port on the 1841), including out to the internet, by name or ip.Can ssh to local router, but not to anything that isn't localDNS is workingDHCP not working using ip helper pointing to DHCP scope on server at main site, have to use static IPCan't rdp to anythingCan't get emailCan't browse windows sharesCan't get to any websites, external or intranet. IE says "Website found, waiting for reply..." but eventually times out.
I did some testing for communication over certain port numbers using telnet and nmap, and found the following:
Can telnet to url.. and local intranet webserver on port 80 (http)Can telnet to two of our Exchange Servers on port 25 (SMTP)If I run an nmap scan on url...com, or our intranet webserver, it confirms that 80 and 443 are open, but the pages will not load. I am able to telnet (port 23) to a state mainframe via the internet that some of our employees use, and I do get the expected login screen. I tried erasing the config one of the new routers, and just added back the bare minimum config to get the circuits up (serial/ethernet interface configs, eigrp), but saw the same symptoms.
One other thing to note: the 2801 at the main site has three other frame relay sites connected to it on the same WIC as the new sites, all of which are working fine.
I just don't understand why I can ping everywhere I need to be able to ping, and port scans show that communication is open over needed ports, but the applications don't work.
View 1 Replies
View Related
Apr 28, 2013
I have a branch office connected to the Head Office through a VPN Tunnel in cisco 1841 Router. If i enable Internet for any pc in Branch Office through cisco router i cannot access it remotely from Head Office. [code]
View 2 Replies
View Related
Apr 27, 2012
I have a Cisco 1841 router that is connected to a switch. I have WAN/LAN configured on the router and the switch is handing out internal IP's. The issus that none of the client machines can access the Internet. From within the router console, I am able to ping external domain names, my ISP DNS servers.
Once the client machines picks up an IP they are unable to ping any external domain names or IP's and not even the ISP DNS servers, but they can ping the Cisco router IP. As a note I have tried my ISP DNS servers and as a test Google's DNS servers, but neither will allow access to the Internet.
Below is the current running config:
Building configuration...
Current configuration : 1440 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
View 26 Replies
View Related
Jul 24, 2012
how to configure a backup route to the internet. My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.
The problem I’m facing is that each ISP is plugged to a dedicated ASA 5510, so 1 ISP in one firewall and 1 in the other. Both ASA are plugged to an internal network in a dedicated VLAN with a L3 switch and that L3 switch manages the internal network.
My question is, how can I tell my switch to use ASA1 to go out to the internet and in case the ASA 1 OR THE LINK TO INTERNET used by ASA 1 fails, use ASA 2? It would be great if I can send traffic to the internet thru both connections at the same time. Also, I know the ASA has High Availability configuration, but that applies only if both licenses in the devices are the same and I have a mismatch with the SVPN license, and also I don't know if with my current topology I can use the High Availability model, so I think I can’t use that option and the solution must be applied in the L3 switch, but I don’t know how to tell it to use ASA1 and if failure of the device or the outside interface plugged to ISP 1, then use ASA2. Besides, I would like to know how to optimize this config to do the switch between internet connections seamless to the users if possible (there are VoIP calls on this floor, so I don't want to drop the calls).
View 5 Replies
View Related
Jul 21, 2011
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
View 6 Replies
View Related
Oct 31, 2012
i have router 1841 have 2 interface.i make routing between vlan by subinterface in router and in switch trunk but vlan 5 cannot access internet
View 3 Replies
View Related
Oct 29, 2012
I have going up the walls the last week.Basically just moved house and got broadband installed, my girlfriends laptop connected automatically, whereas my Compaq CQ60 Presario Notebook WindowsVista will not connectI have checked so many different forums trying to fix this problem, but to no avail im afraid... it looks like there is an excellent internet connection.... but cannot go on the internet because it says "Unidentified Network local access only"
View 6 Replies
View Related
Apr 18, 2012
I want to Turn off my local network's firewall on my computer but i dont know how.
View 1 Replies
View Related
Dec 11, 2011
I tired connecting my Sony TV to the internet.It wouldn't connect automatically so I manually entered
IP Address 192.168.1.200
Subnet Mask 255.255.255.0
Default Gateway 192.168.1.1
Primary DNS 192.168.1.1
Secondary DNS 0.0.0.0
When it tested that it only gave me local access but not internet access. What else can I do to fix this? I use a netgear router WPN824N.
View 3 Replies
View Related
Nov 26, 2011
I just replaced my wireless router. Wh? Now I'm not sure, I hoped a dual band router would give me better range. True or false?Regardless, I installed my new router but can only connect to my local network on my home laptop. However my work laptop connects to the same network and internet with no problem. SO does my husband's work computer.Any idea what the problem is? Other weird thing is that I have some random unsecured network that keeps popping up and my computer keeps automatically connecting. I've tried to remove it every way possible and it keeps coming back?
View 1 Replies
View Related
May 7, 2012
I have recently set up a computer on my network to host a website.So i have done the basics and created a Dyndns account etc.Now I can view the website via this domain flyingant.dyndns.org/ on computers outside of the network and the pc that it is hosted on.But my problem is that I cannot view the website on any other computer on the network, it takes me to the routers login page.
View 2 Replies
View Related
Sep 30, 2012
After I changed the router password today, I am not able to access the Internet through my machine. Seeing the 'Unidentified netwrok, access to local only'. However, other people connected to the same network are using Internet
View 14 Replies
View Related
May 14, 2011
I have a Compaq Presario Windows Vista. I currently have a Wireless router. It used to be Netgear. About 2 wks or so, my company changed it and gave me the password. I am currently connected to the one they changed to but local access only and no internet. Under Network and Sharing Center, it says: Unidentified network (Public network) Access: Local only Connection: Wireless Network Connection (perfectv) Under Internet Options, Connections , it shows the following connection: T-Mobile US Standard Modem When I try using the Windows Network Diagnostics, it keeps coming back with the options that havent worked. The options are: - Plug a cable into the network adapter Local Area Connection - Automatically get new IP settings for the network adapter Wireless Network Connection - A problem with your network router or broadband modem might be preventing an Internet connection Note: I am always able to connect to the internet wherever free wi-fi is available. If a password is required all I need is to obtain it and enter it without making any changes in the system. This is the only time Ive had issues getting online, even though I have the password.
View 5 Replies
View Related
Oct 18, 2011
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....
View 13 Replies
View Related
Mar 17, 2013
If there was a workaround for me to connect to the internet outside of my citrix session? I work remotely for my company through citrix access gateway and can open/access the internet from within the session but any attempt from a browser/program outside of the session times out...I am thinking this is blocked on purpose for productivity reasons, however I want to be able to access the internet from outside of the session so that accessing personal sites for example, gmail, won't be tracked by my company.Would it be possible to run a virtual machine and change IP addresses so access within the machine runs independently of my session?
View 1 Replies
View Related
