As per topology attached herewith, i have 2 ISPs, ISP1 and ISP2. And i have one Cisco 1841 Router with only 2 Ethernet interfaces.My Lan subnet is 192.168.1.0.My puspose is, i want to configure both ISP1 and ISP2 and my Lan Network on router, without adding any extra interaface. I also want to configure a nat so that Lan user can go to internet. I wabt to do this using 2 Interfaces.
View 17 RepliesI configure for our office site to site VPN project. Now I configured already Site to site vpn between ASA 5510 and 1841 router.
HQ LAN
Branch LAN 10.2.1.0/24 >>> ASA 5510>>>>> 1841 >>> INTERNET <<<<<< 1841 <<<<<< 10.30.3.0/24 ^^^^ Call Manager 2851
Now can access from Branch LAN to HQ LAN each other. I face the problems that are
1) In branch LAN , they can access HQ LAN & resource , but cannot access internet. I didn't configure NAT on PH Router
2) Can I access internet from BRANCH LAN through HQ LAN to INTERNET. Or Can I access Internet from Branch LAN from PH Router directly while access to VPN to HQ LAN ?
3) In Branch Site , hard phone cannot work but soft phone on PC can call to HQ. Hard phone IP are same in Remote Network (172.16.1.0/24 ) . Is it problem ? how can I configure separately ?
setup a vpn server cisco.
device cisco router 1841 [URL]
Configuring Cisco 1841 router and firewall.My provider has put their equipment and given me 2 subnets with public ip address. I am used to getting just one Subnet and connecting my firewall straight to the hand off. But in this case I am a bit confused. I assume I will need to put a router and configure it with before I connect my firewall. [code] I also have a firewall that I would like to be on the subnet 2 at 200.xxx.97.130 and have my private network 192.168.xxx.xxx behind it.
View 2 Replies View Relatedhow to configure log in Cisco 1841 router, terminal log
View 1 Replies View RelatedI have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0
^
% Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.
how to configure VPN connection with failover on cisco Router 1841?
View 5 Replies View RelatedI configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
I can not access the configure menu.
I try access with Serial cable blue DB09 / RJ45 on console port and serial ports on PC using putty or hyperterminal but any connection can not be done. The screen stay black and not show any text.
The computer found the port COM1 but i csn not access any information from Cisco router model 1841
how can I configure QoS in the router CISCO1841 for the port IPSEC(UDP 500 ,UDP 4500) and the port tcp 4433
View 5 Replies View RelatedBasically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies View Relatedhow do i configure user authentication via TACACS on UCS 1.4 with ACS 5.2? My TACACs connection works, and my user authentication is successful, but i can only get read-only rights. I have tried several versions of "cisco-av-pair= role=admin" both as mandatory attributes named role and as cisco-av-pair=role , with "admin" as the value, and i still get read-only.
When i attempt to find any documentation, it only describes ACS 4.2, which is another problem i have with most documentation for new cisco products (i have this exact issue with my NAMs, nothing i do to change the attributes results in successfully logging into the NAM, and all config guides are written in 4.2 speak).
is there any possiblity cisco is going to release some documentation on how to convert 4.2 speak to 5.2 speak?
Currently 2811 series router is configured for site to site VPN, CAN I configure USER VPN on the same box. We want Users to connect to VPN Server using Cisco VPN Client. best authentication method for USER VPN
View 1 Replies View RelatedI have a Cisco 2940 switch and a Cisco 1841 router. I want to build two different VLAN networks on the switch, which do not have to communicate one with each other, but those VLANS should communicate with the router.
I read a lot of articles, i tried to configure properly the switch and the router but i still don't get them work.
I set on the switch, the GigabitEthernet 0/1 port to Trunk port and i had to set it a native VLAN. The problem is that only from that native VLAN, i can ping the router.
I am not able to configure the wifi user and password after configure the ssid & passord it is not working according to my requirement
View 1 Replies View RelatedI have some queries regarding on the report generation for on Cisco ACS v5.2.
1) Can we schedule to run a customized report on ACS and then email the report to the user?
2) Can we run a users authentication trend report based on the AD directory group rather than individual user.
3) Can we configure user authentication logs to be viewed on WCS.
I need to configure our ASA5505 firewall for remote access to our network using EasyVPN software installed on a laptop. That laptop will be connected in the different places, using DSL or 3G toggle or Public Wi-Fi. For some people it's very easy, but I don't have any experience with firewalls.
View 9 Replies View RelatedI am trying to configure an ASA 5505 running 8.3 to allow a priv 15 local user to be able to ssh into the device and be placed into priv 15 mode without having to execute the enable command and type the enable password.Right now when you log in as a priv 15 user you still have to execute the enable command and type the enable password to get to priv 15.
View 3 Replies View RelatedI can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies View RelatedI´m looking for the best configuration to restrict a user to read-only. The restriction should be configured via CLI not TACACS+.
-Hardware: 3750 (probably not interesting for this question)
-Oldest IOS: 12.2(53)SE1
The user should be allowed to: see the running-configurationtrigger all kinds of show-commandsping and traceroute from the device.The user should not be allowed to: upload/delete/rename files on the flash-memoryget into level 15 (not sure if I can avoid this)all other commands despite those from level 1 and those specified above.
I am configuring remote access VPN on a cisco router 3845. Works fine.
I was looking for configuring session and idle time configuration for groups and eventually users.
I am using the following Cisco VPN remote access configuration :
crypto isakmp client configuration group mygroup
key xxx
pool mypool
acl 101
max-logins 3
banner ^CHelloo ^C
Is there any command in cisco ios similar to Cisco ASA vpn group 1 session-timeout?
I'm trying to configure my BRI interface in "network protocol-emulate network" and "layer1-emulate network" but i don't have this second command.Is someone have allready to that with this type of interface ?I've to configure this because the ISDN line of my telco is in user mode only.
View 5 Replies View RelatedI need to allow only a few Internet websites from Cisco 1841 Router for my LAN users. What Access-List should be used for this.
View 4 Replies View RelatedMy lease router 1841 is not going behind the Juniper Firewall. i am able to ping and telnet my Juniper firewall, but when i try to ping dns server 4.2.2.2 or any other website it gives me no reply.
Below is the configuration of my Router.
212.50.100.16 ( Juniper Firewall IP)
Router-1841>enPassword:Router-1841#ping 212.50.100.16
Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 212.50.100.16, timeout is 2 seconds:.!!!!Success rate is 80 percent (4/5), round-trip min/avg/max =
[Code].....
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedI have a branch office connected to the Head Office through a VPN Tunnel in cisco 1841 Router. If i enable Internet for any pc in Branch Office through cisco router i cannot access it remotely from Head Office. [code]
View 2 Replies View RelatedI have an issue with NAT on a Cisco 1841. See following configuration,
interface FastEthernet0/0 description Connection to LAN bandwidth 100000 ip address 10.90.0.100 255.255.0.0 ip helper-address 10.100.2.2 ip helper-address 10.100.2.3 ip load-sharing per-packet ip nbar protocol-discovery ip nat inside ip virtual-reassembly duplex auto speed auto
interface Dialer1 description ADSL connection bandwidth 448 ip address X.X.X.X 255.255.255.248 ip access-group 150 in ip nat outside ip inspect firewall out ip virtual-reassembly encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname hostname ppp chap password password ppp pap sent-username hostname password password crypto map vpn
ip nat inside source list 102 interface Dialer1 overload(code )
I've tried this with both a source list NAT statement, and a route-map. The router can contact hosts on the Internet:
Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 128.31.0.51, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 144/147/148 ms
I have configured a Cisco router. I am able to ping google from rotuer. I can ping my local IP from router and router local IP to my machine. But I can not access internet on machine. I can not ping google and any other IP out of network.
View 11 Replies View RelatedI have a Cisco 1841 router that is connected to a switch. I have WAN/LAN configured on the router and the switch is handing out internal IP's. The issus that none of the client machines can access the Internet. From within the router console, I am able to ping external domain names, my ISP DNS servers.
Once the client machines picks up an IP they are unable to ping any external domain names or IP's and not even the ISP DNS servers, but they can ping the Cisco router IP. As a note I have tried my ISP DNS servers and as a test Google's DNS servers, but neither will allow access to the Internet.
Below is the current running config:
Building configuration...
Current configuration : 1440 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
We are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 Replies View RelatedI am in trouble with my cisco 1841 configuration.The "what I want to" schema: very external IP ( AAA.AAA.AAA.AAA ) in the internet cloud => | cisco 1841 external IP BBB.BBB.BBB.BBB | => internal computer IP CCC.CCC.CCC.CCC
View 1 Replies View RelatedI am in trouble with my cisco 1841 configuration. The "what I want to schema":very external IP ( AAA.AAA.AAA.AAA ) in the internet cloud => | cisco 1841 external IP BBB.BBB.BBB.BBB | => internal computer IP CCC.CCC.CCC.CCC
Steps (this what I think should be done):
1. Find all packets from A by acl
2. Route finded packets throught cisco1841 directly to internal ip address
It should be easy but it doesn't.