Cisco Switching/Routing :: 891-W Access Verification Prompt?
Jan 25, 2013
Recieved this unit from an individual who has very little knowledge (like myself) with the 800 series.
I'm having issues just getting into this device, when I power it on and console into the unit i am presented with an "Access Verification" prompt that requires credentials that I do not have/know.
At some point (not sure how) I managed to get to a "yourname#" prompt at which point I configured using this document here and created a username and password and some other basic settings, I saved the config and did a reload and it takes me right back to that "Access Verification" prompt.
Sould I be using the CCPE to gain access to this device instead? Is there a way to recover that "Access Verification" username and pass? How did I ever get to that "yourname#" prompt?
View 7 Replies
ADVERTISEMENT
Oct 27, 2011
I have a 6509E switch with dual 6Kw power supply that is logging "Power supply 1 input has changed. Power capacity adjusted to 2671.20W" then will bounce back to normal at random times from 1sec to 10sec. Is there a command to check what each input level of the power supply to try to identify possibly which source is causing the problem? The power supply input lights remains green while this is occuring.
View 3 Replies
View Related
Apr 1, 2013
I'm trying to test port-security in my c3550 but when I show port-security int f0/23 shows it only "Disabled" as below:
run
interface FastEthernet0/23switchport access vlan 200switchport mode dynamic desirableswitchport port-security mac-address stickyspanning-tree portfast
View 2 Replies
View Related
Sep 19, 2012
Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on. This layer 3 switch will be used to connect to servers.
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
[Code]....
View 6 Replies
View Related
Feb 6, 2013
I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
View 1 Replies
View Related
Nov 3, 2012
I have found that the Catalyst 2955 series switches do not use an external MODE button for getting a switch into the switch: prompt, but they use a break sequence like routers do to get into Rommon state URL
So I was wondering if there is a similar mecanism that applies to other kind of Catalyst switches, like 2960, 3560 or 3750.
View 7 Replies
View Related
Mar 6, 2012
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies
View Related
Nov 17, 2012
I was testing on 802.1x function on Catalyst 2950. the funtion itself work fine with my radius. but after I have setup the aaa new-model, I have no access to my switch!everytime I telnet it prompt me username, but I didn't create any user!!
how to recover to the origianl status, just prompt to input password but not username needed, and with 802.1x enable ofcause. [code]
View 10 Replies
View Related
Sep 29, 2012
I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
View 1 Replies
View Related
Jan 13, 2013
in my run promt i can only run cmd.other commands are not worked
View 1 Replies
View Related
Apr 12, 2011
For weeks guest access to my e3000 worked fine. Today I have a friend come over, his XP connects to the guest wi-fi, but his computer does not get a prompt for a password.
View 6 Replies
View Related
Nov 21, 2012
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
View 9 Replies
View Related
Nov 6, 2011
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".I have made different Default Device Credential sets that I'm using when I add devices to LMS. I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
View 1 Replies
View Related
Mar 31, 2009
I am trying to install a digi cert on a 7921 and I get the message on import of "certificate verification failed".as there does not seem to be much documentation with the above error message.
View 2 Replies
View Related
Jan 3, 2012
I have a problem when doing this report. If I do a device credentials report on a user defined group (40 devices) 11 of these devices fails to connect via SSH. I can make an SSH connection to all 11 devices from the CiscoWorks server, but 11 devices still fails on the report
Device Name Read Community Read Write Community SSH
1. 149.212.XXX.164 Ok Ok Failed to connect.
2. 149.212.XXX.153 Ok Ok Failed to connect.
3. 149.212.XXX.152 Ok Ok Failed to connect.
4. 149.212.XXX.151 Ok Ok Failed to connect.
5. 149.212.XXX.150 Ok Ok Failed to connect.
[code]....
View 2 Replies
View Related
Aug 16, 2011
i get for all devices telnet credential failed in my credential verification report. I exported the device from the Device Manager into a csv file to verify the correct passwords.The export shows the correct values in
<DEVATTRIB Name="primary_username">cwuser</DEVATTRIB>
<DEVATTRIB Name="primary_password">secretpassword</DEVATTRIB>
View 4 Replies
View Related
May 28, 2012
My Dell Laptop is connected to Wildbue via LAN connection to Broadband. January or February I connected Belkin Router to obtain Wi-Fi access for other laptops, Cell and PS3, Everything seemed to be working fine. I tried to disconnect the Dell in order to use it via Wi-Fi. This caused problems when my sons laptop lost connection. My guess was that it was actually routed through the Dell via network. Anyway, as I was working to network all correctly. My sons friend decided that he couldn't wait for internet and forced another laptop to login to internet. In the process, it appeared that he changed by router password so that I could not access it. Being a beginner when it comes to network connections, etc., I spent alot of time trying to correct the Belkin Router. I finally disconnected the router and attempted to remove all detail on my Dell. I am sure that my adapter information is not completely accurate. Or so it appears. Note that I do have LAN internet connection and I can search for wireless access. If necessary, I will reinstall the Belkin Router since it is my understanding that it is needed for Wi-Fi access to my internet provider connected via Broadband modem.
I am sure that there will be corrections. I am sure that there is more that will need to be done in order to provide access to other laptops and cells. At this time, I am getting internet on my main laptop that is connected via LAN connection. However, I am having problems understanding adapters for wireless connects.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsPenis>IPCONFIG/ALL
Windows IP Configuration
[code]...
View 1 Replies
View Related
Feb 21, 2012
I recently installed and configured the Prime LMS 4.1 Soft Appliance. After discovering the devices on the network I ran a credential verification check on everything. All of my devices passed accept for the Nexus 7010s and Nexus 5020s -- these show up in the failed device report with a BLANK value for SSH and "Did Not Try" under Enable by SSH. I have verified SSH is enabled and accessible outside of Prime, and that there are no access lists preventing access. All other tests pass for these devices.
I've also visited the troubleshooting workflow section for these devices, and when I test the connectivity, SSHv2 passes.
I've downloaded all of the updates available for the device packages and have tried other credentials. All other aspects seem to be working properly.
View 10 Replies
View Related
Jun 4, 2012
I'm trying to troubleshoot a problem with mpls fast reroute. The primary (protected) link is between PE-PE and the backup link is PE-P-PE. The IGP I'm using is OSPF. When there is a issue with the primary link and debug mpls tra tunnels signalling there is a message "LSP-TUNNEL-SIG: TunnelX [237]: re-route path verification failed (protected) [Can't use link x.x.x.x on node x.x.x.x]". After 30 seconds (without ospf tuning) the SPF is recalcalated, but that's not the point From the show mpls tra tunnels tu1013 (the backup one)everything looks ok:
Status:Admin: up Oper: up Path: valid Signalling: connected From show mpls tra fast-reroute database everything is ok, the status is Ready I'm using 7206VXR, Version 12.4(24)T3
View 0 Replies
View Related
Aug 2, 2011
We plan to use machine certificates on our notebooks with Windows Vista. Our authenticating server is Cisco ACS 5.1. To access the wireless network we want to use the machine certificate of the notebook and a verification of the corresponding computer account in the Active Directory. What authentication method is the best to check the machine certificate and if in the Active Directory exist the enabled corresponding computer account ? How to configure the ACS and the notebook to use it like described ?
View 1 Replies
View Related
May 24, 2012
I seem to get conflicting information on using the Management port as a regular routed interface on the ASA5510..The management interface can be used for the traffic that passes through the firewall as well. The Security Plus License for the ASA 5510 is required in order to use the management0/0 port as a regular interface. With a base license on the 5510, the management0/0 port cannot be used as a regular interface.
I believe that I saw another post that mentioned it was part of the standard IOS if you had a later version.
View 2 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Jan 23, 2013
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
View 5 Replies
View Related
Dec 11, 2012
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
View 14 Replies
View Related
May 11, 2011
There's something funky going on with my prompt for a pair of multiple context ASAs. In the system execution space I have the following command:
View 6 Replies
View Related
Sep 7, 2012
Almost new switch giving error: %%Low on memory Try again later.This is a 2960 48pt lanbase image.I can't get a console prompt, telnet in or anything, it is however switching packets OK. [code]
View 1 Replies
View Related
Jul 16, 2012
I have AP which is not connected to switch.I console it and it gives error unable to to get IP from WLC.Need to know is there any way that i can go to command prompt of this AP without getting IP from WLC? I tried control + c etc it does not go to command prompt.
View 8 Replies
View Related
May 30, 2011
My PS3 recently got stolen. I was informed that the detective assigned to my case can contact Sony with the serial# and MAC address to track it down.I realize that there is this way:" If all you have is the serial number SCEA would need the MAC address, and only SCEJ has the "master list" of serial number to MAC address comparison. All SCEA would need from your local PD is an affidavit request / warrant (whatever their specific agency prefers to use or call them) asking SCEA to acquire said information."However, I also realize that I can find my MAC address through command prompt on my windows. However, there are more than one MAC addresses (or physical address as referred on the command prompt). My Question is, how do I know which one is the same as my PS3 MAC address?
There are these choices:
Wireless LAN adapter Wireless Network Connection 2:
Wireless LAN adapter Wireless Network Connection 2:
Ethernet adapter Local Area connection
Ethernet adapter Bluetooth Network Connection
View 2 Replies
View Related
Aug 17, 2012
how to send a file using command prompt ?
View 1 Replies
View Related
Jul 21, 2012
i there any way to send tje file using command prompt option for sending a file if we have the ip address of the person to whime we want to sand the file
View 1 Replies
View Related
Jan 9, 2012
Having issue with WLC 5508 using ACS 5.2 tacacs+ protocol to do device management.The problem statement is after key in the username and password on the WLC login page, it is endlessly prompt for authentication on WLC. Whilst on ACS monitoring and reporting i able to see it is successfully authenticated, shown at AAA protocol > TACACS+ Authentication.On ACS, the shell profile for this is setting role1 , value = ALL.
View 3 Replies
View Related
Apr 11, 2013
I work in a lab testing interoperability between Avaya and Cisco VoIP products.I am setting up an environment to test Avaya 96x1 phones with VPN using SCEP going thru an ASA 5510 to a backend IP PBX.
Environment: Windows Server 2008 R2, Enterprise Edition, AD with DNS, NDES Cisco ASA 5510 running 9.0(1)
I would like to setup certificate enrollment between a Windows Server 2008 R2 and a Cisco ASA 5510. Here are the commands that I use for the Cisco ASA 5510:
crypto key generate rsa modulus 2048 crypto ca trustpoint ASA5510-trust enrollment url http://10.129.112.20/certsrv/mscep/mscep.dll enrollment retry period 5 enrollment retry count 3 password Interop123 exit crypto ca authenticate ASA5510-trust crypto ca enroll ASA5510-trust
Everything works as expected until I try to enroll. There is no prompt for the enrollment password and the certificate request is denied.
ciscoasa(config)# crypto ca enroll ASA5510-trust%% Start certificate enrollment ..% The fully-qualified domain name in the certificate will be: ciscoasa.avayasil.avaya.com% Include the device serial number in the subject name? [yes/no]: NoRequest certificate from CA? [yes/no]: yes% Certificate request sent to Certificate Authorityciscoasa(config)# The certificate enrollment request was denied by CA!
Why isn't there a prompt for the enrollment password?BTW, If I set "enforcepassword" to "0" in the Windows registry, then it works.
View 1 Replies
View Related
