Cisco Wireless :: Getting Command Prompt On AP 3502i?

Jul 16, 2012

I have AP  which is not connected to switch.I console it and it gives error unable to to get  IP from WLC.Need to know is there any way that i can go to command prompt of this AP without getting IP from WLC? I tried control + c etc it does not go to command prompt.

View 8 Replies


ADVERTISEMENT

Wireless :: PS3 MAC Address Through Command Prompt On PC?

May 30, 2011

My PS3 recently got stolen. I was informed that the detective assigned to my case can contact Sony with the serial# and MAC address to track it down.I realize that there is this way:" If all you have is the serial number SCEA would need the MAC address, and only SCEJ has the "master list" of serial number to MAC address comparison. All SCEA would need from your local PD is an affidavit request / warrant (whatever their specific agency prefers to use or call them) asking SCEA to acquire said information."However, I also realize that I can find my MAC address through command prompt on my windows. However, there are more than one MAC addresses (or physical address as referred on the command prompt). My Question is, how do I know which one is the same as my PS3 MAC address?
There are these choices:

Wireless LAN adapter Wireless Network Connection 2:
Wireless LAN adapter Wireless Network Connection 2:
Ethernet adapter Local Area connection
Ethernet adapter Bluetooth Network Connection

View 2 Replies View Related

How To Send A File Using Lan / Command Prompt

Aug 17, 2012

how to send a file using command prompt ?

View 1 Replies View Related

Send A File Using LAN / Command Prompt?

Jul 21, 2012

i there any way to send tje file using command prompt option for sending a file if we have the ip address of the person to whime we want to sand the file

View 1 Replies View Related

Command Prompt To Show Devices On Network?

Jan 30, 2013

I am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.

I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!

View 1 Replies View Related

Find Wifi Password Through Lan Or Command Prompt?

Dec 4, 2012

How to find the password through lan or cmd

View 2 Replies View Related

Broadcast A Message On Network Using Command Prompt?

Aug 10, 2011

how do i broadcast a message on my network using command prompt?

View 2 Replies View Related

Windows Xp - Command Prompt Appears And Disappears?

May 19, 2012

Windows XP sp3 home edition.On login in when the PC open the desk top the icon opens and a command prompt flash and desappears

View 1 Replies View Related

IP Address Displays A Question Mark On The Command Prompt

Mar 15, 2011

When I went to the cmd prompt and typed in ipconfig/all I got...

Ethernet adapeter Wireless Newtork Connection 4:
Description- Dell Wireless Mini Card
Physical Address-00-1E-4C-05-99-B3

[Code].....

View 1 Replies View Related

Command Prompt Suddenly Appeared Copying Files?

Nov 18, 2012

I was using my laptop - working in MS Word and hadn't even opend a internet browser and suddently a command prompt appears and all i managed to see before closing it from the task manager (which had it running through internet explorer i think) was that it was copying files.Its a work laptop so i would like to know if it was remote access from IT which seems doubtful on a Sunday or if i need to be concerned about security. Is there a relatively easy (considering i have zero programming experience) way for me to check if anyone logged on with remote access and who and what files were copied?

View 2 Replies View Related

Linksys Cable / DSL :: Upload HTM File To WAG200G Using Command Prompt?

Feb 9, 2011

is it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?

View 3 Replies View Related

Cisco Wireless :: 3502i LED Not Remaining Lit?

Oct 17, 2012

I am in the process of deploying 3502i APs. This site has 2 - 5508 WLCs both running Software version 7.0.220.0 and 2 - 4402 WLCs both running the same version of software as the 5508s. All of the APs that I have installed so far have joined the controller and I can associate to them and access the network. When the APs first are connected to the switch they go through the 'normal' boot up with the LED changing colors - white, red, green, blue (not necessarily in that order). Once the AP has completed its boot sequence the LED goes out and remains NOT lit.
 
This is happening to most but not all of the APs. This is the first time I have deployed 3502s - previous experience is with 1142s and 1242s and the LED does not do this with them.
 
I can, through the CLI, turn the LED on but it is then ALWAYS blue, even if a device is NOT associated to it.
 
I do not want to leave them off because the account will believe they have a 'dead' AP and with them always blue they cannot properly troubleshoot using the LED.

View 5 Replies View Related

Cisco Wireless :: Area Coverage With 3502i

Nov 4, 2012

In an idle situation how much area is covered by a cisco 3502i acceccpoint , I understand there are many factor that will effect this , thats why I am adking in idle situation , I am looking for a number is square feet.

View 1 Replies View Related

Cisco Wireless :: Can 3502i Be Downgraded To Autonomous

Oct 1, 2012

Can a 3502i be downgraded to autonomous mode?

View 7 Replies View Related

Cisco Wireless :: Stand Alone 3502I Without Controller?

May 10, 2012

I have a customer with several older Aironet 1121G WAP's.  In one area of the plant the noise levels from several large motors is preventing reliable connection to the WAP, even though it is located in the same conference room as the users.  I am suggesting upgrading the 1121G to the 3502I to take advantage of the Clean Air technology.  This raises two questions:
 
1) Will a single 3502I be able to effectively handle the RF noise, or does it require a network of WAPs to function properly?
 
2) Does the 3502I require the CT2504 controller for the Clean Air to work, or will it function in a stand alone mode?

View 8 Replies View Related

Cisco Wireless :: 3502i Autonomous To Lightweight?

Apr 28, 2013

how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
 
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.

View 4 Replies View Related

Cisco Wireless :: 3502i Cannot Join Controller?

Oct 15, 2012

When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
 
This is the illustration
 
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
 
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
 
Through research, those APs were getting a wrong IP address,
 
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
 
We also added the cisco-capwap-controller.localdomain  to our DNS servers, and then I rebotted the APs and still no luck.
 
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
 
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?

View 3 Replies View Related

Cisco Wireless :: 3502i Cannot Join 5508

Sep 25, 2012

I have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.
 
[code]....

View 4 Replies View Related

Cisco Wireless :: 3502i AP Does Not Download The Code From The Controller

Nov 27, 2012

I am having a Wism on 6500 chassis with software code 7.2.103.0 Now......... I use to have 7.2.111.3 on the Wism before but for some reason I had to downgrade the code to an older version (some compatibility issues with the NCS)......
 
Now before all the APs were having 7.2.111.3 version running as soon as I downgraded the controller IOS most of them downgraded the code but a few still did not show up...... so I picked one of them and did a factory reset on the AP and was guessing that it might get the new code from the controller this way but unfortunately since than I have tried a lot of things but no luck. I have switches configured on layer 3..... other APs connected to this switch are working fine,........ when I reset the AP to factory default it doesnot take an IP obviously so I manually define the IP,,, you would find that configuration below too.... but than after a while it trys to locate the controller and could not find it.... where as, as i said other APs on teh same switch works fine......
 
the only thing i notice is that it does not release the IOS .. it is still having 7.2.111.3.....
 
using MCNG ddr static values from serial eeprom
ddr init done
 Running Normal Memtest...
Passed. 
IOS Bootloader - Starting system.

[Code].....

View 4 Replies View Related

Cisco Wireless :: 3502i Keeps Losing Communication With WLC 5508?

Jan 17, 2013

This problem only seems to affect one of our sites.  Every once in a while, several APs would lose link to the 5508 and get stranded.  The only way to fix the issue is either to power cycle, or better yet SSH into the APs and use the command "capwap ap controller ip address x.x.x.x", and then they'd automatically rejoin the controller.  At first, I thought network hiccups caused the APs to lose connectivity, but there's none that I could find.  I have the primary/secondary controller IPs configured in them as well.  See log below:
 
[previous log entries show AP working as intended, then...] 
*Jan 18 05:29:29.632: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_ECHO_REQUEST
., 1)
*Jan 18 05:29:29.632: %LWAPP-3-CLIENTEVENTLOG: Switching to Standalone mode
*Jan 18 05:29:29.645: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jan 18 05:29:29.645: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to [ommitted due to security reason]:5246
*Jan 18 05:29:29.704: %WIDS-6-DISABLED: IDS Signature is removed and disabled.

[code]....

View 2 Replies View Related

Cisco Wireless :: 3502i - How To Restore The Factory Settings

Jul 18, 2012

The ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,

View 3 Replies View Related

Cisco Wireless :: 2504 WLC / 3502I AP - Internet Connection

Dec 4, 2012

We have a 2504 WLC and 8 352l AP. All AP are working and can be seen in the WLC except 1. It can grab an ip address but cannot see on the WLC. the show AP join...only shows that it is trying to join but no error indicated. A debug cap swap events didn't show the ip add.

View 7 Replies View Related

Cisco Wireless :: 3502i - Dot11 Interface Shutdown

Dec 15, 2012

My 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
______________
      
interface Dot11Radio0
no ip route-cache
shutdown
antenna gain 0
beamform ofdm
mbssid(code)

View 10 Replies View Related

Cisco Wireless :: Upgrade Aironet 3502i To Lightweight?

Nov 15, 2011

How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?

View 9 Replies View Related

Cisco Wireless :: WLC2106 And 3502i Radio1 Not Showing Up

Mar 2, 2013

I have a WLC2106 and AP3502i. The issue that I am having is the radio for 5GHz is not showing up in "Wireless > 802.11a/n" (see attached screenshot) I am not exactly sure what was the problem. When I went to 802.11b/g/n I do see an entry for 2.4Ghz radio, but nothing on 5GHz.
 
I have the AP plugged directly to my 3550POE, and when I used the command "show power inline" it says that the switch is providing 15.4W and there is still 345W remaining on the switch. The LED on the AP is solid green. I issued a no shutdown on dot11radio1 and the status is up/up, but there is still no entry under "Wireless > 802.11a/n"

View 23 Replies View Related

Cisco Wireless :: How To Upgrade To Mini IOS Version 7.3.1.73 On AIR-CAP 3502I

Mar 7, 2013

how can i upgrade to Mini IOS Version 7.3.1.73 on the AIR-CAP 3502I. we some that have Mini IOS Version 7.3.1.73 and some that have Mini IOS Version 7.0.112.74. want them all the same.

View 1 Replies View Related

Cisco Wireless :: Aironet 3502I - How To Configure Device

May 14, 2012

I have a newly purchased Aironet 3502i that I would like to configure on my network.  I am new to Cisco networking in general, and would like to know how to configure the device to operate without a WLAN Controller.  

View 4 Replies View Related

Cisco Wireless :: 3502i Ceiling Pole Mounting Options?

Jul 11, 2012

I've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above).  Ceiling is roughly 30-50' up.  Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling. 
 
Problem is I can't find any bracket or mounting options for this!  What are others using in this situation for mounting one of these access points onto a metal pipe such as this?  I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs.  Anyone mounting access points this way?

View 4 Replies View Related

Cisco Wireless :: Convert 3502i AP From Mesh To Access Point

Sep 27, 2011

I mis-ordered some 3502i’s . They came with Mesh image by accident.
 
Can I just setup DHCP Option 43 TLV to point to my WLC, plug the AP in and have it change from Mesh to LWAP?
 
How do I switch from Mesh to LWAP without touching console?

View 6 Replies View Related

Cisco Wireless :: 3502i - Sporadic Disconnects When 802.11n Is Enabled In Clients

Jul 11, 2012

Recently I upgraded the wireless infrastructure in my campus and deployed WISM2 controllers and Cisco 3502i APs throughout the campus. Until now all my users were using 802.11b/g/a speeds without any issues. However, now I am trying to enable 802.11n speeds in a test group of users by enabling AES encryption and I am seeing lot of issues. These test users sporadically loose wifi connection and an asterix appears in the WIFI icon in the task bar. Interesting part is that all the manually configured wireless networks in the laptop stop displaying. The broadcasted SSIDs continue to show up though. All these users are using "Intel(R) Centrino(R) Advanced-N 6200 AGN" wireless cards with driver version 13.3.0.24. I had upgraded one of the client drivers to the latest 15.1 version. However, he still complained about wireless disconnection (I am not sure about this problem as I didnt personally attend his laptop to know the cause of diconnect).
 
One another interesting incident is that 2 people from this test group were having a meeting in a conference room once and surprisingly both dropped at the same time with the same symptoms. The only fix was to reboot their PCs.
 
I have done following changes in my controllers hoping that the problem would get fixed, But still no luck.
1. Enabled client band select.
2. Checked EDRRM for A as well as B/G
3. Changed Channel allocation from freeze to auto.
4. Enabled "avoid persistent interferers".
 
In my calls with Cisco support we also ran debugs in the controller and sniffer captures in the client machine. All we see in the controller is that the client dropped without any reasons. Also, didnt find anything significant in the sniffer captures. At this point not sure what to do. If upgrading the client driver is an option, then I need to produce some proof or document to the management which says the current 13.3.0.24 has known bugs to run 802.11n speeds. Scanned the entire internet, put a post in intel support site but no luck.

View 1 Replies View Related

Cisco Wireless :: 3502I Access Point Unsuccessful Software Upgrade

Jan 16, 2013

I have a trouble with AIR-CAP3502I-R-K9 AP.I tried to upgrade IOS software in ap because it was connecting  and disconnecting to controller too often. I already upgraded one of two  access point and it working stable at this time, but the second one  not. [code] So, I even can't load new software. What can I do now?

View 19 Replies View Related

Cisco Wireless :: 3502i Mounting Plate Welded To Security Hasp?

Feb 20, 2013

Not sure why Cisco is shipping like this? It is a pain to mount them. Earlier we had option to slide out the Secuirty hasp.

View 1 Replies View Related

Cisco Wireless :: 3502i - Max Number Of WLANs / SSIDs Configured On H-REAP AP

Sep 7, 2011

What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
 
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved