I have a newly purchased Aironet 3502i that I would like to configure on my network. I am new to Cisco networking in general, and would like to know how to configure the device to operate without a WLAN Controller.
View 4 RepliesHow to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedWe recently had the Aironet 3502i APs installed in our infrastructure and are having a bad time with hosts connecting to them. The controller sees them, they have an IP, they are showing a solid green light, but you cannot get devices to connect. If you reboot the device you get about 5 seconds of connection and then it disconnects. The only cure seems to be rebooting the APs, but I am baffled why this keeps happening. The installer is blaming our devices, but it is happening to laptops, thin clients, and even cell phones. From what I've seen, everything works fine until, i believe, the device tries to refresh it's lease and is unable to do so.
View 6 Replies View RelatedI just configured Aironet 3502i and it works ok but no lights. I could see the AP in switch, in WLC, and in WCS and ping ok but when you see it mounted it has no light. I tried to shutdown the port in the switch and I saw it turns green (booting), once it was registered in WLC the light will be off.
View 12 Replies View RelatedWe have a Cisco aironet 1162N connected to a Wireless Controller (LIGHTWEIGHT mode), the device failed and it needs to be replaced.We have a Cisco aironet 1142N in stock available to use.Can we proceed with the change just with disconnect the failed AP (model: 1162N ) and connect the new one (model: 1142N)? Or there is any other task to be done before the change? since the WLC manages the configuration for each AP.
View 8 Replies View RelatedI am tryign to set up an Aironet 1142, I have created a reserrvation in DHCP using the MAC address, and the reservation shows as active, but I cannot connect to the device with my browser.
View 1 Replies View RelatedI have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedI just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
Does the AP is able to configure 2 public ip address of the DMZ-WLCs?
like ip 1.1.1.1 in my US data center, whereas a second ip 2.2.2.2 in my EU data center?
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedI'm trying to configure my Linksys E2000 to be an ethernet attached wireless device to use on computers instead of dongles, etc. I don't want it to route, just act like a Wireless card.
View 1 Replies View RelatedI'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .
View 9 Replies View RelatedI just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View Relatedif i can configure the cisco aironet 3500i without WLC controller.
View 1 Replies View RelatedI am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below
%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
and the ssid is not getting broadcasted. kindly let me what could be the cause.
[code]....
I've purchased a wmp600n pci adapter january this year and installed it with no problems and did not encoutner a single problem with it until today. I use windows 7 64bit.
I've just came back from a 3 week absence and turned on my computer for the first time since i left. I notice that I have no wireless connection. So i go to network connections and realize that my wireless adapter dosent even show up..only my lan card. So i check my device manager, and under network adapters, i can see my wireless adapter, but with an exclamation mark next to it. I check the properties, and under the status box, it gives me this message.Your computer's system firmware does not include enough information to properly configure and use this device. To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35).
So i do what it says, and flash my bios to the latest version. After the update, I check the device manager, and the error message is still there. I check my wireless adapter driver version and it is v3.0.2, which is the latest version according to the linksys driver download webpage. I've tried uninstalling and re-installing the adapter but no luck there. I also checked to see if maybe there was a problem with my pci slot and that was not the problem because I was able to use my older wireless adapter.
I am in the process of deploying 3502i APs. This site has 2 - 5508 WLCs both running Software version 7.0.220.0 and 2 - 4402 WLCs both running the same version of software as the 5508s. All of the APs that I have installed so far have joined the controller and I can associate to them and access the network. When the APs first are connected to the switch they go through the 'normal' boot up with the LED changing colors - white, red, green, blue (not necessarily in that order). Once the AP has completed its boot sequence the LED goes out and remains NOT lit.
This is happening to most but not all of the APs. This is the first time I have deployed 3502s - previous experience is with 1142s and 1242s and the LED does not do this with them.
I can, through the CLI, turn the LED on but it is then ALWAYS blue, even if a device is NOT associated to it.
I do not want to leave them off because the account will believe they have a 'dead' AP and with them always blue they cannot properly troubleshoot using the LED.
In an idle situation how much area is covered by a cisco 3502i acceccpoint , I understand there are many factor that will effect this , thats why I am adking in idle situation , I am looking for a number is square feet.
View 1 Replies View RelatedCan a 3502i be downgraded to autonomous mode?
View 7 Replies View RelatedI have a customer with several older Aironet 1121G WAP's. In one area of the plant the noise levels from several large motors is preventing reliable connection to the WAP, even though it is located in the same conference room as the users. I am suggesting upgrading the 1121G to the 3502I to take advantage of the Clean Air technology. This raises two questions:
1) Will a single 3502I be able to effectively handle the RF noise, or does it require a network of WAPs to function properly?
2) Does the 3502I require the CT2504 controller for the Clean Air to work, or will it function in a stand alone mode?
how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
I have AP which is not connected to switch.I console it and it gives error unable to to get IP from WLC.Need to know is there any way that i can go to command prompt of this AP without getting IP from WLC? I tried control + c etc it does not go to command prompt.
View 8 Replies View RelatedI have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.
[code]....
We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedI am facing problem while connecting my VPN server configure at UC540 device. this device is behind my ISP router. i applied port forwording of IPSEC traffice to my cisco device which configured as vpn server. now if i try to connect with my Live IP i get the following error. [code] I test if i connect using 192.168.0.116 internally it works but if i try to connect using my Live IP it trying and trying but not connect..
View 3 Replies View RelatedI´m getting started on ciscoworks and i trying to configure a device discovery to start but i have some questions about how configure this tool exist 5 parameters that i have to configure to start the device discovery.
•Configuring Discovery Module Settings
#
•Configuring Seed Device Settings
[Code]....
I want to add devices that found neighbors via CDP son in the configuring discovery module setting i choice that option In the configuring seed device setting i choose DCR as seed device that means those devices already in the DCR start discovering from those devices but you can add more seed devices how i can add a seed device ? with ip addres or something like this? and this device have to be in the DCR already or not? The configuring SNMP settings, this community correspond to what device? the devices that i want to add ? and in the field target name what ip adders have to be? and if i have different community of snmp in my devices what device and snmp community have to configure in this parameter
I am having a Wism on 6500 chassis with software code 7.2.103.0 Now......... I use to have 7.2.111.3 on the Wism before but for some reason I had to downgrade the code to an older version (some compatibility issues with the NCS)......
Now before all the APs were having 7.2.111.3 version running as soon as I downgraded the controller IOS most of them downgraded the code but a few still did not show up...... so I picked one of them and did a factory reset on the AP and was guessing that it might get the new code from the controller this way but unfortunately since than I have tried a lot of things but no luck. I have switches configured on layer 3..... other APs connected to this switch are working fine,........ when I reset the AP to factory default it doesnot take an IP obviously so I manually define the IP,,, you would find that configuration below too.... but than after a while it trys to locate the controller and could not find it.... where as, as i said other APs on teh same switch works fine......
the only thing i notice is that it does not release the IOS .. it is still having 7.2.111.3.....
using MCNG ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
[Code].....