I state that I'm very fast Voip router configurations, the problem is as follows: I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 in the motion that the 2102 can receive and make calls.
View 4 RepliesI have one POTS line and a SIP account with Skype. I want to configure my SPA3102 to take all incoming POTS calls (so I don't have to change my phone number or use up my bandwidth all the time). I want all local calls (303 and 720 area code) and possibly 911 (if possible) to go out the POTS line, but all long distance to go to SIP account on SKYPE. Pretty simple, but I can't find a wizard or samples in the documentation or firmware for the SPA3102.
View 1 Replies View RelatedHow to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies View Relatedsimple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View RelatedIs it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
Is it possible to configure two AG241 adsl routers back to back via two wire line as a Lan to Lan network?
View 8 Replies View RelatedI previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies View RelatedThe reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies View Relatedhow T line contributed to voice transmission.
View 4 Replies View RelatedOne of my branch offices is connected to an ADSL line as well as a VDSL line.Since I really don't need the ADSL line I came up with the idea to use it as a backup line.So I searched google and found this nice little article URL. I wonder if the router will switch back to the primary ISP if the primary line comes up again?
View 3 Replies View RelatedI was working on a problem the other day and came across something that I had seen before but never given much thought. I had a router with a switch connected to it and the interface was showing as Ethernet0 is up, line protocol is down. The problem in the end turned out to be a cable that had fell out because it was not connected correctly, but I was able to replicate this interface status on a router (FastEthernet0/0 is up, line protocol is down), and NO cable was attached to the interface.I've had a look on the internet but cant seem to find a good answer, so does anybody else know why this status is shown on the router? Remember, NO cable is connected to the interface so it isn't a speed or duplex problem
View 5 Replies View RelatedI ran across this today on a 7200 that when all the vty lines are filled, and dont release, you enter clear line vty x and it is supposed to release the line. Well in some versions it doesn't work.
Here is the work around I found. clear tcp line vty x
how to bring this interface back up? It's a 1252 with 80211.n.I started configuring it with CLI and then was using the web interface. I made a change on the web interface and it caused the AP to hang. I rebooted it and can access via Hyperterminal, but I cannot ping the IP address nor bring it up in the web interface any longer.I tried the "No shut" command in the BVI1 interface.
View 4 Replies View Relatedwe have one OC-24 private line between our data centers. we are looking to get best throughput but we get max. avg throughput of 300Mbps with peaks of 800Mbps throughput. i.e. we transfered 2TB of data over this link and we got average throughput of 300Mbps with peaks of 800Mbps.
we should at least be getting 800Mbps throughput since we have OC-24 (1244Mbps) private line. we contacted our ISP but they said there isn't any problem in private line from ISP side. what can we do to increase average throughput?
I was wondering about the folling witch i found in a Cisco 1941 running config
View 2 Replies View RelatedWe have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
How do I plug in a LAN line
View 1 Replies View RelatedWe have a barn that is quite a difference from the house and would like to add a router out there also, since all our animal sales are done from that point. We just have one phone line for the house and for the barn.
View 2 Replies View RelatedI have a cisco 2911 set up at one of my sites and it is configured with sub-interfaces as this provides a default gateway to each of the offices.I have just had a 100mb leased line put in and i have a couple of questions regarding the config.let me start by telling you how it is set up .I have 3 HP Procurve switches connected together then that connects to the Cisco and the Cisco connects to a Zywall
HP Switches > Cisco 2911 > Zywall > Internet
We are wanting to remove the Zywall and connect the Cisco to the Leased line box
HP Switches > Cisco 2911 > Leased Line > Internet
The config of the cisco is
G0/0 - is up but no cable connected as this holds the sub-interfaces
G0/1 - Connects the Zywall - 192.168.1.1 (this has firewall rules to forward traffic through)
G0/2 - Leased Line
The way i have configured the sub interfaces is with its own DHCP pool and default router, some of the offices have there own ADSL router and hold there own Internet connection and the default gateway for that is 192.168.xxx.253 and the offices that use the Cisco use default gateway of 192.168.xxx.254
Now my question is how would I move everyone onto the Leased line and get rid of the Zywall ? Would it be as simple as giving the leased line an address and put in a static route to forward all traffic through that connection ? Or am i missing a trick or 2.
My 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies View RelatedI've just want to confirm if I can protect a router (telnet and ssh) putting 2 ACL's (one IPv4 and other IPv6) on the same line vty. Something like:
line vty 0 4
access-class hostsIPv4 in
ipv6 access-class hostsIPv6 in
Do I have to use named ACLs?
Im looking for MIB for monitoring 6500 line card from availability prespective;
View 1 Replies View RelatedIm trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
I configured a 1841 router that connects to a DSL modem. This DSL connection is our Internet connection for vendor and IT testing. I have connectivity to the Internet using nat and have configured the router to act as a DHCP server. It seems to be working fine. I just want to configure some best practices for securing the device from the outside access. Is there some standard best practices I should be configuring?
View 2 Replies View RelatedI see differrent voltage in line card ws-6704. Iam afraid of something went wrong with my 6500 switch. two 6500 switch is redundant.
View 3 Replies View RelatedNow I am tring to setup Cisco 1812j with ISDN Line.
Here is what I connect the device. (I am in Japan)
ISDN Line (NTT east) >> DSU(NTT east INS Mate V30Slim with S/T port) >> Cisco 1812j(S/T)
On DSU setting I enable DSU and Disable Terminator.
First of I would like to test outbound call. Here is the config.
interface BRI0 ip address 192.168.92.2 255.255.255.0 encapsulation ppp dialer map ip 192.168.92.1 name Router1 broadcast 080********(Cell Phone Number) dialer-group 1 isdn switch-type ntt isdn point-to-point-setup ppp authentication chap ppp chap password 0 CISCO ip route 10.92.0.128 255.255.255.248 BRI0 192.168.92.1
Then I test by ping with #debug dialer. #ping 10.92.0.129
And I could not receive a call by my cell phone landline either.
Here is the debug.
[Code]....
we have noted the automatically removing of the only "nat (inside,any)" line, during the upgrade of ASA 5540 from 8.4(3) to 8.4(4) 1: why ?
View 1 Replies View RelatedI'm replacing a PA-POS-OC3-SM with PA-POS-1OC3 in a flex Wan module (WS-X6582-2PA) in Cisco 6506 using WS-SUP32P-GE PISA.I have a hard time bringing the "protocol up. the status I see is line up and protocol down. Debug shows (attached) no comunication with the edge router but when i put the older PA (PA-POS-OC3-SM ) back evertything works fine and older PA has been running for many years without the issue. I'm replacing older PA is becuase this is going EOL. I had opened a TAC case but the TAC engineer added no value. [code]
View 2 Replies View Related