How To Configure To Use Router With Lease Line
Feb 14, 2011
How to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
View 1 Replies
ADVERTISEMENT
May 26, 2011
- I just need internet in all 15 PCs - I do not want them to be connected with any sever locally or in network but my demand is internet on all system with good speed.
View 5 Replies
View Related
Feb 21, 2012
simple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
View 15 Replies
View Related
Apr 30, 2012
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies
View Related
Jan 10, 2008
Is it possible to configure two AG241 adsl routers back to back via two wire line as a Lan to Lan network?
View 8 Replies
View Related
Dec 18, 2010
I state that I'm very fast Voip router configurations, the problem is as follows: I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 in the motion that the 2102 can receive and make calls.
View 4 Replies
View Related
Nov 12, 2012
configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies
View Related
Dec 7, 2011
Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
View 2 Replies
View Related
Jul 23, 2011
I have a smc wireless cable modem gateway router lease is set to expire every 7 days does it matter if its like more often, is this good enough, i was told every day might be better as i get better connection.
View 2 Replies
View Related
Nov 3, 2011
I previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
View 1 Replies
View Related
Jun 11, 2012
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
View 2 Replies
View Related
Dec 20, 2012
Small company, under 10 computers, wired and wireless printers, straightforward network. Do not need (nor particularly want) Smart Wi-Fi, Cloud Connect, or or anything other than a simple manually-setup router. Have a new EA6500 I plan to use replacing an E1000 that is playing up (needs to be reset every morning) connecting to Verizon east (former GTE) aDSL. Connected the EA6500 to a laptop via ethernet, changed router password to same as E100, set up the two port forwards I'll need (IPs on the internal network are static in the 192.168.1.0/24 block), changed DHCP server to start at 101 (don't ask), leave Internet Connetion Type setting at "Automatic Configuration - DHCP" (same as E1000), shut down both routers and modem (Westell WireSpeed 890-210015-04). Connect EA6500 to modem, power up modem, power up router, and...Nothing. Does not receive external IP via DHCP.If I switch back to the E1000, it immediately picks up the IP lease.
View 6 Replies
View Related
Aug 9, 2012
a couple days ago my BEFSR41 started making trouble, and so far I have not been able to get it working properly again. When I hook up my laptop directly to the cable modem everything works fine, and I get an IP address via DHCP. When I connect through the router, though, the router status shows 0.0.0.0 for all DNS, gateway, etc. addresses, and even pressing DHCP Release/Renew doesn't change that.Also, in the log I see these messages:
2012-08-08 20:30:41 warning DHCP RENEW WARNING - Field invalid in response
2012-08-08 08:30:52 notice TLV-11 - unrecognized OID
Since I can connect to the cable modem directly, it seems the cable modem is not at fault.My overall setup is:
- BEFCMU10 cable modem
- BEFSR41 (not sure which version, but I believe it's a 4.x)
- WAP54G
Could it be that my provider (Cox Communications) has changed some configuration in their DHCP server, and my laptop (MacBook Pro) can handle it, but the router cannot?
View 1 Replies
View Related
Sep 25, 2011
i cant seem to change my dhcp lease time even though i change my Client Lease Time to 1 day.
Firmware Version:v1.0.06 build 001 Apr 29 2011 11:08:40Boot Code Version:v0.03Firmware Verification:Current Time:Sun, 25 Sep 2011 10:15:32 PMInternet MAC Address:Host Name: Domain Name:
View 6 Replies
View Related
Jul 8, 2011
I just bought an e4200. I was using a LinkSys WRT54GS running DD-WRT alternative firmware.
One feature that I really liked in DD-WRT was the ability to assign static IP leases from the DHCP server. I liked having all of my devices running with a predictable, known IP address on my network. I have a Home Theater PC, and various controller applications that run on iPhones, etc. - some pretty homebrewed. Configuring the firewalls, etc. was much easier with IP address based controls.
Is there a way to achieve the same within the e4200's stock firmware?
View 1 Replies
View Related
Jul 7, 2011
Can the client lease time be set to never expire to prevent loss of connection for wireless printer with a permanent ip address on E3200? Or is there another way to ensure continuous connection?
View 6 Replies
View Related
Jun 11, 2012
we finally got my Cisco refurbished E2500 configured and working downstream from a UVerse 3801HGV box. We had to change the default IP address of the 3801 because it conflicted with the E2500's default. The E2500 is set up to get its Internet IP address using DHCP from the 3801. This is working fine for normal web browsing, etc. However, anything that requires extended connections (downloads, streaming, etc) freezes after a couple of minutes, forcing me to refresh the action to get it started again. Extremely annoying to say the least.
I'm pretty sure that I've tracked it down to the E2500's configuration of the 3801's DHCP allocation. For some reason, the E2500 wants to set the DHCP Lease Time for the 3801's assigned IP address to 10 minutes regardless of the upstream settings from the 3801. The 3801's default is 24 Hours which I've changed to 168Hours (7 days), but the E2500 stays stuck at 10 Minutes. Specifically, I'm referring to the setting displayed on the E2500 under Status>Router>Internet Connection IPV4>DHCP Lease Time.
View 9 Replies
View Related
Jun 26, 2011
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
View 1 Replies
View Related
Apr 28, 2013
I have a Linksys WRT310N v1 with firmware v1.0.10 build 002Jul 19, 2010 My router fails to renew it's DHCP lease from my cable provider, causing internet access to drop. I can still access my cable modem at 192.168.100.1, but I must do a "IP Address Release" then "IP Address Renew" to get back internet access. The router works fine otherwise.
View 6 Replies
View Related
Apr 2, 2013
I'm trying to change the DHCP Client Lease Time from 1440 minutes to 480 minutes. When I try to apply the new settings, I'm getting a message that says "Invalid Characters" and it won't stick. I've tried this in three different up-to-date browsers (ie10, Chrome and Firefox). Also, I'm connecting locally through LAN and I have the latest EA6500 Firmware: 2.1.39.145204
View 2 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
Mar 27, 2012
The reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies
View Related
May 5, 2013
my Laptop is about nine years old, HP Pavillion Pentium 4. I run Windows XP Home Edition Version 2002 SP3. I use a broadband card from Verizon that I just put in my USB (no router, etc) I'm getting a System Error Source DHCP Event ID 1002. When this happens, my computer, I believe, is going into sleep mode and I have to reboot the system. When I turn it back on and go back on the internet, all my websites that I was in are still there. The error says: The IP address lease 10.170.223.48 for the Network Card with Network address 2c3068c16ED1 has been denied by the DHCP Server 10.173.229.86 (The DHCP Server sent a DHCPNACK message)The DHCP Server Service did not extend the lease on your computer's IP address, so your computer temporarily lost its connection with the Network. I tried the ipconfig /release and ipconfig /renew. I tried going in services.msc and going under DHCP and keeping it automatic but stopping it. I called Verizon and I believe he refreshed my Network settings (I think I knew more about the topic than he did) He said it was my computer, whatever. I just tried the static IP but it didn't seem to take. I restarted and it jumped back to automatic. My last guess is it's something to do with the time frame of when it automatically obtains the address and when it expires. When I do the ipconfig /all it shows only a two hour time frame before it expires. Today I noticed that my computer shut down/sleepmode at the exact time the ipaddress was obtained. So, is there a way to increase this time between obtaining and expiring?
View 7 Replies
View Related
Mar 28, 2011
delete a lease from a DHCP scope on a WLC 5508? I'm using that unit as the dhcp server, no relay. I am unable to find anything either through the web or cli.
View 2 Replies
View Related
Mar 22, 2011
I've recently purchased 5 WAP610N access points to replace my older US Robotincs access points.I've configured one WAP610N (upgraded to the latest firmware i found on the site) with a static IP, bropadcasted SSID & WPA2 personal security.I had no problem at all to connect PC's but when i tried to connect the Ipad & Iphone (with the latest 4.3 firmware) i was able to connect to the network but unable to get an IP lease.
I had no problem before connecting to the US roboticx access points.When i change (lower) the security to WEP on the WAP610N then everything works fine but i want to use WPA2 in stead of the unsecure WEP protocol.
View 1 Replies
View Related
Jan 25, 2011
I've been having this issue for about 3 months now, off and on, never seemed to be predictable but started happening more and more, which prompted me to look into it.
Currently, the DSL Modem is configured in bridge mode with the ASA handling PPPoE. The WAN address is being assigned via DHCP. The ASA is running 8.2(1). The WAN interface will drop it's DHCP lease and will not renew it without power cycling the DSL modem. I did a little bit of googling and found mention of setting "dhcp-client client-id interface outside", specifically this was an issue pre 7.2(22), but doesn't seem to affect my situation. Originally, I had the MTU on the outside interface configured as 1500, changing it to 1492 has not resolved my issue either.
I've enabled PPPoE and DHCPC debugging and posted the results below when the event occurs, I'm thinking this is moreso a PPPoE issue than it is a DHCP/DHCP Lease issue as I am not seeing any debug messages from DHCPC.
Code...
View 1 Replies
View Related
Jun 23, 2010
I have several Cisco WAP4410N access points. They are configured to automatically obtain an IP address through DHCP. This works fine, but I've discovered when the DHCP lease expires, the access point doesn't renew it. It continues to use the same IP address but does not renew the lease. If I reboot the access point, it will renew the lease again.Is this a known issue with the WAP4410N? Is there any way to work around this, other than setting a static IP address or rebooting regularly?
View 9 Replies
View Related
Mar 26, 2013
N-Wireless modem Router F5D-8636 will not let me change the lease time from half an hour?
View 1 Replies
View Related
Apr 10, 2013
Region : UnitedKingdom
Model : TL-WR842ND
Hardware Version :
Firmware Version :
I've just set up an old netbook as a secure ftp server on my network. As part of the process I locked the server host IP by making the lease permanent in the DHCP/Address Reservation page of the routers web GUI.However I later noticed the MAC binding page which seems to achieve the same thing (lock an IP address to a specific adapter). I was wondering what the practical differences between the two techniques are? i.e is it better to use binding than reservation?
I have the gut feeling that binding is more robust as I'm not sure what happens to a reservation if the specified host device is removed and then the router rebooted, is the address released back to the pool of available addresses? Binding feels like that address will never be made available to another device even if that device is no longer present, or is that completely wrong?Also does the binding survive a router reboot?
View 2 Replies
View Related
Sep 26, 2012
I have a remote site on a 2811 IOS 12.4(15). Interface FA 0/0 faces the ISP and is set for DHCP. What command can I run to see all of the information given out with the IP lease from the ISP? I need to find out what the IP address of the DNS servers are.
View 3 Replies
View Related
Nov 26, 2012
Is there a way on the security appliance SA520 to remove someone from the DHCP lease client manually rather than setting the DHCP lease time to expire in less time like 4 hours or 2 hours. I was able to do this on other routers by highlighting the connected device and click remove. If not any recommendations on how to handle the device that are attached via DHCP and the person is no longer here, but the lease time is not up. I have set DHCP lease time to 4 hours.
View 1 Replies
View Related
Jan 12, 2012
How to clear dhcp lease in WLC 6.0.199 from the IP leased from internal server?
View 1 Replies
View Related
Apr 1, 2011
I use an adsl router DSL-320B to connect my Linux server (Fedora 12) to the web.I noticed in my logs that it was renewing its ip about every 30s.
View 1 Replies
View Related
