Cisco VPN :: 888 Configure VRF With COOP Having Primary And Secondary Key Servers
Jun 19, 2012
We are trying to configure vrf aware GET VPN with COOP having primary and secondary key servers and also 3 GM routers. All GM routers we use are Cisco 888 and Key servers we use cisco 2911 routers. All GMs crypto maps have been applied into Vlan interface as there's no L3 interface on 888 routers.
Always members can form a tunnel with primary KS, we have configured redundancy with secondary key server and listed on each GM primary and secondary KS on GDOI group.
The issue we facing is that whenever we shutdown the primary or secondary servers the tunnel is not forming with available KS unless otherwise we mannually clear the crypto session. In another way when primary KS down it doest not fall back to secondary KS and no GM get registered. We have already played with all the timers such as DPD, SA lifetimes, GDOI rekey lifetime etc and also exchanging the keys (import/export) with KS and COOPs but there's no luck. We could see the following message was seen on both KS.
[code] 192.168.1.3 is the primary KS and 192.168.1.6 is the secondary KS.I captured attached debug output from 1 GM and secondary KS while I shutdonw the primary KS and also attached is our senario we were trying get work.
Also attached is the show output from both KSs when it form a tunnel with GM.
View 2 Replies
ADVERTISEMENT
Jun 16, 2011
it is possible de use two servers ACS 5.2 (primary and secondary) in active/ active? or just in active/ passive?
View 3 Replies
View Related
Jun 22, 2011
How can you figure out your primary and secondary DNS? I have a linksys router, and i'm trying to figure out what my primary and secondary DNS are so i can hook up my PS3 online.
View 1 Replies
View Related
Apr 25, 2011
I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
View 19 Replies
View Related
Jan 22, 2012
I have a question about the number of Cisco licenses needed in two cases for ACS 5.3 Virtual Machine.One primary + One secondary : Just one license for all or one license for the primary + another one for the secondary ?One primary + several secondaries : Just one license for all or one license for the primary + just one license for all the secondaries ?
View 1 Replies
View Related
Jun 11, 2012
Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
View 3 Replies
View Related
Feb 22, 2013
I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies
View Related
Dec 5, 2011
We have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
View 7 Replies
View Related
May 15, 2013
Management purchased a HA package from Cisco consisting of 2 5508's with pre installed 500 users license on the Primary WLC and none on the secondary WLC. We have 5508's already so I am familiar with setting them up and so forth. What I am not familiar with is setting them up using HA for failover and license sharing. I've looked and looked and can't find documentation online showing how to set this up. I have found some but nothing that is complete. I have spent 2 days spinning my wheels.
View 2 Replies
View Related
Apr 21, 2013
I have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
View 8 Replies
View Related
Aug 9, 2011
IP address of Primary had to be changed, to respond to a hardware failure of TACACS server with IP in many device configs.
Now the Secondary fails to respond to repeated "Deregister from Primary" requests, even after reload - apparently because it cannot reach the Primary at its old IP address.
Requesting Deregister in GUI generates pop-up that says, "This operation will deregister this ACS Instance from the Primary Instance. Management applications on this ACS instance will be restarted and you will be required to login again. After performing this operation
[code]....
View 1 Replies
View Related
Nov 2, 2011
Cisco ACS 5.2 secondary server is configured as a log collector for both primary and secondary server .Now i am facing problem in log collection from primary server .ACS secondary server is not collecting any logs from primary .
View 2 Replies
View Related
Apr 12, 2011
I have a pair of ASA5520s in active/active failover - this works fine. Both primary and secondary ASAs are running 8.2(2) code.I have a 30-day temp 50 seat SSL license that I applied to the primary. I then started having problems with L2L tunnels.
I noted that if the 'show crypto isakmp sa' state for an L2L was MM_STANDBY, then the remote protected net could not reach my side. However, I could ping across to the other side at which time the state changed to MM_ACTIVE as I would expect and the remote could then reach my side.
I believe this results from the differences between the two licenses. When I applied the 50 seat SSL lic. it disabled failover, but I was willing to risk that for a few days to do show my customer the benifits of SSL connectivity. Note license differences. Is this causing the MM_STANDBY IKE issue and if so can I overcome it and use the 50 SSL VPN Peers lic.
[code]...
View 3 Replies
View Related
May 11, 2012
I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies
View Related
Aug 25, 2011
Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
View 1 Replies
View Related
Jan 7, 2013
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
View 4 Replies
View Related
Feb 5, 2011
my partner cannot connect to the internet on her computer. I have tried disabling the ipv6, typing in oranges dns server in the ipv4,and attempted to find the dns automatically. I tried running the ipconfig, but it flashes up for a second then goes off before I can look at it. As mentioned I am with Orange, I contacted them and they wanted to run the computer through an ethernet cable and reset everything which I think is a pain in the backside and I know it should be a bit simpler than that.
View 14 Replies
View Related
Dec 27, 2012
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies
View Related
Sep 12, 2012
I am getting little confuse about the configuration of my second WLC .I have a project going on with main office and 10 sites . I have placed my primary WLC 5508 with software 6.0 and all the branches i deployed ap . I put all the AP in Hreap mode did VLAN MAPPING . And i Created Groups based on the location and i put this AP's insde those group .All the sites seems perfectly working. Now I have to place my sedcond WLC in one another branch . I did all the initial configuration of my 2nd WLC .
But am worried if my primary wlc fail how could it can be taken to second WLC . And if i put inside wireless--> hight avaliabilty--primary ip and secondary ip .Again do i need to configure those WLAN , AP GROUPS , everythink in this WLC sepretely or any option . If i need to create the group do i need to select the ap's which already added to primary wlc groups.
View 1 Replies
View Related
Nov 24, 2012
We already have a subnet defined to inside interface and is in produciton. the default gateway is this interface ip. In that setup now I have to add one more subnet and as the first subnet is been defined in ASA indside interface, I have to assign secondary Ip to the inside interface so that new subnet users can easily reach here and go outside.
View 1 Replies
View Related
Oct 16, 2011
how to configure the backup port for the management interface for a WLC 2112. I see in the documentation that it states:
"Each interface is mapped to at least one primary port, and some interfaces (management and dynamic) can be mapped to an optional secondary (or backup) port. If the primary port for an interface fails, the interface automatically moves to the backup port. In addition, multiple interfaces can be mapped to a single controller port."
But nowhere can I find where it says how exactly to do it. Google seaches have come up empty as well. I am connecting the WLC to a 3750 stack, and would like to have a secondary port from the WLC connected to the second node of the 3750 stack. So far I have connected port 1 (management) of the WLC to a port on node 1 of the stack which is configured as a trunk and everything is workign fine. I have also connected port 2 from the WLC to a port on node 2 in the stack that is configured the same as the port on node one. how to tell the WLC to use port 2 as the management backup if needed.
[URL]
View 2 Replies
View Related
Feb 21, 2012
simple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
View 15 Replies
View Related
Apr 22, 2012
How to assign NAT IP to server from Firewall
View 2 Replies
View Related
Jan 11, 2011
I have windows servers connected on cisco switch 4500 series. Issue is when server NIC configure with Teaming, some times servers gets not reachable, and after restarting the servers it gets reachable. Is 4500 series switch support the teaming software?
View 3 Replies
View Related
Nov 27, 2011
is there a owners manual for Toshiba Canvio Portable Hard Drives?
View 1 Replies
View Related
Feb 5, 2011
I want to set up ipchain firewall of my ubuntu so that it prevents to traffic to an specific IP address?
View 1 Replies
View Related
May 31, 2011
the linux server should be configured with LDAP, so that any user should not login into that machine by local user credentials but by his intranet credentials.
View 1 Replies
View Related
Apr 25, 2011
In my collage i have a LAN to the wind server 2003 again i m also configure a small LAN may be take a 5 computer but the communication is not done.
View 1 Replies
View Related
Sep 18, 2012
I'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
[code].....
View 23 Replies
View Related
Nov 9, 2012
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
I have read how to configure the Virtual Servers - Forwarding url...and added two entries, one for port 44612 and one for 32680 , my pc ip is 192.168.0. 100.Before I installed the router (my pc was connected directly to the lan connection) all was working just fine.And I double checked that the ports are not being blocked by firewall.
View 4 Replies
View Related
May 1, 2012
I can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies
View Related
Jan 1, 2013
I'm looking for a way to configure Cisco ACE4710 loadbalancer to bypass traffic that is initiated from server side to Internet?Are there any way to configure this, so that the loadbalancer will not maintain session for this bypass traffic to maximize throughput?
View 1 Replies
View Related
Jun 11, 2013
We are planning to split the Private servers from the DMZ Servers and configure an additional Interface and segment for this purpose.
Private Servers Segment: 192.168.4.0/24 (there is no DHCP all servers' IPs are statically configured)
DMZ Segment: 192.168.3.0/24 (This is a future deployment)
LAN Segment: 172.17.0.0/16
Both, Private Servers and DMZ Servers are in a collocation as well as the ASA5520. There are multiple Branch offices that uses subnets within the 172.17.0.0/16 Network and they are connected to the ASA5520 via Metro-E.
I do not know if this is possible but what I want to do is this:
In order to avoid the change of internal DNS records I want to mask the DMZ servers with a Private Server IP when a Private server or LAN host wants to access it like this:
The FTP server in the DMZ has the IP address: 192.168.3.100. But when a PC from the LAN wants to reach the FTP server it should points to its old IP: 192.168.4.100. This way the PC sends a packet to the ftp.corporate.net (192.168.4.100) the ASA recieves the packet and translate it to the (192.168.3.100) and send it out through the DMZ Interface.
Also if the Private Servers wants to reach the same FTP the ASA will act like a proxy-ARP and send the paquet to the DMZ by means of the translation of the IP.
View 6 Replies
View Related