Cisco Application :: Configure ACE 4710 For Load Balancing Speech Servers?
Sep 18, 2012I'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
[code].....
ADVERTISEMENT
Cisco Application :: SIP Load Balancing With ACE 4710?
Nov 8, 2011SIP Load balancing Issue with ACE 4710?I have a Cisco ace 4710 with vesion Version A4(2.2). i configued simple SIP load balancing first without stickiness. without stikeiness we are having a problem because bye packet at the was not going to the same server all the time that left our port in used even though user hang up the phone. its happen randmly. i have a total 20 licenced ports and its fill out very quickly. so i dicided to use the stickiness with call-ID but still same issue. below is the config
rserver host CIN-VOX-31
ip address 172.20.130.31
inservice
rserver host CIN-VOX-32
ip address 172.20.130.32
inservice
[code].....
Cisco Application :: ACE 4710 Server Load Balancing?
Jul 7, 2012We have two Cisco ACE 4710 and we want to install both of the devices in HA with load balancing mode.While i have done HA mode configuration between ACE 4710.But unable to configure load balancing configuration between them.i want to tell you connectivity between server,client & loadbalancer.Our Web servers are connected to VLAN 152 on the L3 (3750) switch.Which are alreday working in redundancy between other L3.And ACE 4710 it is also connected to vlan 150 which are connected to same L3 (3750) switches and users are also connected to vlan 6 on the same L3 itself.
View 2 Replies View RelatedCisco Application :: ACE 4710 (1) SSL Certificate Import ( 2 ) With Load Balancing?
Dec 3, 2012I am performing a deployment, in which i require clarity on the following. Our setup has DC and DR , in each site we have two devices for HA.We have received One SSL Certificate from Public CA, Kindly clarify the following doubts i have on thisIn Doc, i found Cert.pem and key.pem is required to generate the pair ,do i receive both Cert.pem and key.pem from the CA or we can generate key.pem from Cert.pem ?SSL Offloading is planned for the X application, and it is running in both DC and DR ( Considering each having their own Public IP address ) , do i need to have two different public certificates or a single certificate can i use in both DC and DR.Load Balancing IssueIs it possible to configure in ACE to access the service in Business hours and in non Business hours to display HTML page showing this is available only during these hours ?In DC we have Three Web Servers ( only in One physical server the service is active, other two are backup ), and these three servers are under cluster and shares one cluster IP , In ACE we have created the VIP and Pointed to only Cluster IP ( like pass through only ). The issue we face is if active web server is down, even then ACE is sending the traffic to that webserver only instead of sending it to the new Active web server. let us know if any solution is there to overcome this issue ?as per my understanding instead of giving cluster IP as real server IP we can issue the three physical servers. now i dont require load balancing between three servers instead require failover king like if first server is down then it should forward to Second server ?
View 4 Replies View RelatedCisco Application :: ACE30 Load Balancing Across Two Slightly Different Servers
Apr 10, 2013is there a possibility to get a load balancing across two rservers so: when client sends http://vip/ and it goes to rserver1 then url is sent without change when client sends http://vip/ and it goes to rserver2 then url is modified to http://vip/xyz/
Or maybe load balancing can be done across two serverfarms ?
Cisco Application :: ACE 4710 Multiple Services Running On Load Balanced Servers
Jan 30, 2012Our Exchange 2010 hub servers run multiple services/ports: smtp, www, pop3,135, 143, https, 993, 995, 6001,6002,6003,60200,60201,8400, and 8402 what is the best way of balancing these servers so that if only one of the services failed on a server, it would switch only the failed service to remaining servers. At present I only use an smtp probe, so as log as that sevrice is running the server is marked good.
View 3 Replies View RelatedCisco Application Networking :: How To Configure ACE 4710 Bypass Traffic From Servers To Internet
Jan 1, 2013I'm looking for a way to configure Cisco ACE4710 loadbalancer to bypass traffic that is initiated from server side to Internet?Are there any way to configure this, so that the loadbalancer will not maintain session for this bypass traffic to maximize throughput?
View 1 Replies View RelatedCisco Application :: URL Load Balancing In ACE 20?
May 23, 2011I have 2 rservers 10.30.1.73, 10.30.1.76,I have 3 URLs in both
[URL]
I want to have only one link for two same link in both servers with this ip address 10.30.1.172 so I will have 3 link and will load balance to 6 links
[URL]
Cisco Application :: 389 Load Balancing LDAP In ACE?
Dec 5, 2011Does loadbalancing ldap services in ACE? Both port 389 and 636.
View 4 Replies View RelatedCisco Application :: ACE20 Load Balancing
Apr 26, 2011I have a problem with the ACE 20 load balance
To start with following is our architectural request flow:
Load Balancer --> Webseal /(reverse proxy) --> HTTP Server --> Portal Server
We have Hardware Load Balancer Cisco ACE20. When we access our portal from Webseal server it works totally fine without any issue, but when we access the same application using ACE we face the following issues:
1) Some of the links on do not work. For eg: We have a link "subscribe" which points to [URL], whenever we click on this link, the request is directed to [URL] i.e homepage
2) URL redirection does not work We have some links which have a url forwarding or redirection for example when we open [URL] it forwards the requests to [URL] opendocument....., but this redirection fails and again the request is thrown to homepage i.e., [URL]
3) The response of the request and the overall portal when accessed via ACE is very sluggish and it takes 20 seconds for homepage to load, whereas the homepage loads in 4 secs when accessed via webseal.
Below is the ACE details.
Hardware Product Number: ACE20-MOD-K9 Card Index: 207 Hardware Rev: 2.3 Feature Bits: 0000 0002 Slot No. : 7 Type: ACE
Software loader: Version 12.2[120] system: Version A2(1.4) [build 3.0(0)A2(1.4) adbuild_11:54:12-2009/03/05_/auto/adbu-rel2/rel_a2_1_4_throttle/REL_3_0_0_A2_1_4] system image file: [LCP] disk0:c6ace-t1k9-mz.A2_1_4.bin installed license: ACE-SEC-LIC-K9
Cisco Application :: ACE 4700 Not Load Balancing
Oct 26, 2011I'm running an ACE 4700 appliance, i have a 4 server serverfarm setup, non-ssl, with leastconns predictor...i have tried round robin as well, and nothing...
I've taken each rserver out of service, and placed back in, and still, the traffic is handed off only to 1 server...
I do have sticky persistence (IP subnet)...
Cisco Application :: CSS 11501 Load Balancing With X-forwarded For Address
Sep 15, 2011We have a pair of CSS 11501,Currently it is using source ip for load balancing and 5 servers as backend , however we have users loggin in using http and based on its source IP (ISP PROXY) , it is forwarded to SERVER A.However, we have a SSL page and when the client switches over to SSL , it is forwarded to SERVER B/C/D/E based on its source IP ( REAL CLIENT IP) .This will cause the user to be terminated as the 5 servers are independent and not running in a cluster.
Is there any way that we can use the X-Forwarded-For address to load balance so that when users loging , they are sent to SERVER A (Based on X-Forwarded-For Header IP which translate to REAL CLIENT IP).This way we are able to also send it back to the same server when it uses SSL.I believe that we should be able to load balance using X-Forwarded-For IP or to rewrite the X-Forwarded-For IP into client source IP.
Cisco Application :: ACE30 Normal Load Balancing In Routed Mode
Sep 23, 2012We are in the situation we have a active configuration with ACE30 doing normal load balancing in routed mode, we have tons of rservers going out on a VIP.we now had to add a new private network to a provider that strangely enough does not want to see our public or private addresses. we need to loadbalance towards him on a priovided subnet (still rfc1918) (IOS VRF bug? is that correct?)I have two options, add the network (new interface) to the active loadbalancers (contexts) and then tie in new policies to the active serverfarms or make a new context just to load balance towards this provider.(preferred)Now - If I do this, the rservers see the client source addresses from this new provider. as the loadbalancer does not "hide" the client IP's. I would then have to add static routers toward the new context - I would want to skip that.
is there a way, to make the loadbalancer hide the client addresses towards the rservers ? perhaps I'm just needing the correct search term to find the config example.
Cisco Application :: Load Balancer For ACE-4710
Mar 25, 2012I am receiving this error while the device is booting up :
kernel=(hd0,1)/c4710ace-t1k9-mz.A5_1_1.bin ro root=LABEL=/ auto console=ttyS0,9
600n8 quiet bigphysarea=32768 [Linux-bzImage, setup=0x1400, size=0xe719b73]
Cisco Application :: ACE 4710 Webpage Very Slow To Load When Going To ACE
Aug 13, 2012Experienced the same sort of behaviour with an ACE 4710 version A3 (2.5). When trying to connect to a webpage on port 443, the pages over 1 minute to download fully. I have timed the download using the plug-in firefox. What is strange is that the browser successfully makes the connection, 200OK etc, but each 'get' takes a very long time to transfer. If I go directly to the server and don't pass via the ACE the page takes between .7 and 1 second to transfer.Is there a way to speed this transfer up, I am currently looking at connection maps.
View 1 Replies View RelatedCisco Application :: ACE 4710 Load Balancer Usage
Dec 13, 2011We are using Cisco ACE 4710 for load balancing the servers. The predictor used is 'least connections'.Have observed the below;The number of connections for a particular server in a serverfarm is 15 in the Cisco ACE.The actual number of users in that server is 6.All the users access using the VIP.Still i couldn't understand why there is difference in the number of users in the server and the load balancer statistics.
View 2 Replies View RelatedCisco Application :: 4710 - Load Balance Two / Three ISPs Using ACE?
Oct 16, 2011How to load balance two/three ISPs using ACE.
What might be the default gateway?Can i create a serverfarm with two rserver with different subnets?
Cisco Application :: ACE 4710 / Transferring Files Between Servers?
Jan 25, 2012We have deployed an ACE 4710 and its working perfectly. But the problem is that after I chage the default gateway of the servers I am not able to transfer files from one server to other. Is there any special configuration needs to be done on ACE to achieve this?Other than copy Ping, telnet and everything is working fine from the servers. These servers are in the same subnet & VLAN.
View 3 Replies View RelatedCisco Application Networking :: ACE 4710 Configuration Of Load Balancer
Jan 22, 2013I am configuring a load balancer from cisco, a ACE 4710.Load blancing is completely new to me, and i am unexpereinced in this field. It has to be configured for a customer that want to load balance HTTP and RTSP traffic over 4 application servers (Back-end),I searched alot on google for possible solutions, and got RTSP in some way to work, but http wont work says my customer.
[Code] .....
Cisco Application :: Ace 4710 - Same Context Routed And Load-sharing?
May 16, 2012Can an ACE 4710 have , in the same context - servers which are
a. just being routed to
b. a set of load-shared servers
I have been told you may not be able to do this on this version?
Cisco Application :: ACE 4710 HTTPS Load Balance Configuration
Apr 16, 2012Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later. I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
View 6 Replies View RelatedCisco Application :: ACE 4710 - Load Balance Https Based On Url
Nov 15, 2011I am trying to configure ACE 4710 to load balance base on the URL, If it matches the specific URL ( /456/ ), the traffic will be sent to server farm 456 else the traffic will be sent to server farm 123.
I attached an image of the topology.
Ace Config:
rserver host SRV01_123
ip address 192.168.1.101
inservice
[Code].....
Cisco WAN :: How To Configure Load Balancing On 6509 Switch Between Two ISP
Jul 22, 2012We have two 100 MBPS P2P link from two different ISP and we have terminated both the link on our 6509 switch. Now we want to configure the load balancing between these two disfferent ISP 100 MBPS P2P link.
So, how to go and what all options we can try ? We are thinking for Ether Channel configuration. Need your expert opinions on the same and if etherchannel configuration is the option then what would be the configuration for the same ?
Cisco Application :: ACE 4710 Load Balance Only If Primary Server Fails
Oct 14, 2012I've done a lot of ACE work over the years but this is the first time this has ever come up.
I have a request from an application group where I have 3 rserver in the server farm but they want all traffic to only go to the first server unless that server fails. If the first server fails, only then do they want traffic to go to the 2nd server instead and if that fails, then traffic goes to the 3rd.
I've read through the documentation but haven't figured out a way to do this. What to do this type of failover configuration?
Cisco Application :: Configuring Load Balancer (ACE 4710) - Unable To Ping VIP
May 13, 2013I have trouble with new installation LB ACE 4710 for Oracle application load balance. Problem: Unable to PING VIP - 10.11.10.55 / 24
Below are the simple configuration parameters:
1. ACE 4710 is connected with Cisco 3560 Switch - L2 Trunk (Channel Group)
2. Cisco 3560 Switch is connected with Cisco 6500 Switch (Core) also L2 Trunk
3. There are 3 Vlans,(255, 310, and 370), Vlan 255 is management Vlan
4. Real Servers and Virtual IP are part of Vlan 310
- VIP - 10.11.10.55
- Real Server1 - 10.11.10.46
- Real Server2 - 10.11.10.47
5. Gateway is 10.11.10.1 (vlan 310), 10.11.70.1 (Vlan 370)
Cisco :: Configure Multiple Next-hop Entries And Have It Perform Load Balancing?
May 2, 2012Can you configure multiple next-hop entries and have it perform load balancing?
Example
route-map test
match ip address test
set ip next-hop 1.1.1.1
set ip next-hop 2.2.2.2
Cisco :: Configure Load Balancing In MPLS Between Two Different Service Provider?
Dec 19, 2012How to configure load balancing in MPLS between two different service provider.
View 4 Replies View RelatedCisco WAN :: 12416 Configure Static Route Load Balancing
May 14, 2011I got an issue when configure my 12416 router.
I plan to configure Static route load-balancing, which just assign different administraive distance to static routes.The route with lower distance is preferred. For example, if ISP A is our primary Internet provider the default route may be configured with a distance of 1 (all static routes are assigned this administrative distance) and the default route through ISP B may be configured with a distance of 100. In that case the default route through ISP B will be used if only the route through ISP A becomes unavailable.
But when I trying to configureWith Enhanced Object Tracking to do the route failover (a generic track object can monitor presence of an ip route, state of an SLA), I found my IOS not support such Track command. [code]
Cisco Application Networking :: ACE 4710 Test Web Servers / Need To Use ACE As Their Default Gateway
May 26, 2011I'm setting up an ACE 4710 in our test lab before deploying in production. Do the test web servers I am using need to use the ACE as their default gateway? The are currently configured to use a multilayer switch on their vlan as their gateway but I'm guessing the ACE needs to see the return traffic for load balancing to work correctly?
View 2 Replies View RelatedCisco Application :: ACE 4710 Deployment - Load Balance HTTPS Requests From Internet
Oct 17, 2012I’m looking for some notes from the field guidance here from those that have much more deployment experience.
I have a GSS and an ACE, and its the ACE that's primarily giving me something to think about, in terms of placement and what mode to adopt.
The traffic flow will look loosely like this:-
Client---Internet---Firewall---GSS---ACE---Servers
Physically, it's like this. The RED line denotes a boundary, and pretty much anything North of that is not accessible to us, we simply have a L3 trunk between our switches and "their" switches (S3/S4) and talk using EIGRP.
There are other servers in the top tier, some that also require load balancing, some that don’t. Typically, I want to load balance HTTPS requests from the internet, to one of the 3 servers in the top half.
I’m not sure what mode to select, routed, one arm? What about placement of the ACE? At the moment, I’ve just configured 1/1 on it and made it part of the MG MT VLAN, it's S VI exists on the S1/S2 switches, so I’m open to change as it's still all in the lab.
Cisco WAN :: 5510 - Configure Load Balancing 2 Switches And Active / Standby On ASA?
Jan 26, 2012now i have some problem on Cisco Switch 3750 and ASA 5510, i would like to do loandbalancing on Cisco Switch 3750 and Active/Standby on ASA 5510.
which topology that we can use on this diagram, i mean which protocol connect 3750(2unit) to ASA 5510(2unit) and ASA 5510 to 3750, which protocol 3750.
Cisco Application :: CSS 11503 - Server-to-server Load Balancing?
Feb 16, 2012I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
Cisco Application :: ACE 4710 SSL Cannot Configure Backup Sticky Network
Sep 24, 2012I'm looking for some documentation I can share with a customer to explain why I can't configure them a back-up sticky server farm when we're not terminating SSL on the the ACE (we pass SSL from the client through to the rservers, sticking the client to the rserver by source IP address). I've not been able to find anything that addresses this particular scenario in my googling so far. I remember discussing this in my training class with the instructor, but I can't find any reference to it. Have any of you run into this and have a link they can share?
View 7 Replies View Related