I am receiving this error while the device is booting up :
kernel=(hd0,1)/c4710ace-t1k9-mz.A5_1_1.bin ro root=LABEL=/ auto console=ttyS0,9
600n8 quiet bigphysarea=32768 [Linux-bzImage, setup=0x1400, size=0xe719b73]
We are using Cisco ACE 4710 for load balancing the servers. The predictor used is 'least connections'.Have observed the below;The number of connections for a particular server in a serverfarm is 15 in the Cisco ACE.The actual number of users in that server is 6.All the users access using the VIP.Still i couldn't understand why there is difference in the number of users in the server and the load balancer statistics.
View 2 Replies View RelatedI am configuring a load balancer from cisco, a ACE 4710.Load blancing is completely new to me, and i am unexpereinced in this field. It has to be configured for a customer that want to load balance HTTP and RTSP traffic over 4 application servers (Back-end),I searched alot on google for possible solutions, and got RTSP in some way to work, but http wont work says my customer.
[Code] .....
I have trouble with new installation LB ACE 4710 for Oracle application load balance. Problem: Unable to PING VIP - 10.11.10.55 / 24
Below are the simple configuration parameters:
1. ACE 4710 is connected with Cisco 3560 Switch - L2 Trunk (Channel Group)
2. Cisco 3560 Switch is connected with Cisco 6500 Switch (Core) also L2 Trunk
3. There are 3 Vlans,(255, 310, and 370), Vlan 255 is management Vlan
4. Real Servers and Virtual IP are part of Vlan 310
- VIP - 10.11.10.55
- Real Server1 - 10.11.10.46
- Real Server2 - 10.11.10.47
5. Gateway is 10.11.10.1 (vlan 310), 10.11.70.1 (Vlan 370)
how to capture the incoming and outgoing packets on the balancer?The load balancer is connected in between the customer DCN and cisco switches 2960.The reason of capturing both incoming and outgoing packets on the balancer is to prove to our customer that there is no packet loss issue on the balancer, and it could be some issue on their DCN network.Since it is a production server, I will need to ensure that there is no impact to the incoming and outgoing traffic on the balancer and other networking equipments as well.
View 1 Replies View RelatedWe have a CSS 11503 with the following partial config [code] it is clear that the server at 10.10.10.222 is active. What we cannot understand is why web site is inaccessible thru load balancer using http://10.10.10.1.
View 2 Replies View RelatedSIP Load balancing Issue with ACE 4710?I have a Cisco ace 4710 with vesion Version A4(2.2). i configued simple SIP load balancing first without stickiness. without stikeiness we are having a problem because bye packet at the was not going to the same server all the time that left our port in used even though user hang up the phone. its happen randmly. i have a total 20 licenced ports and its fill out very quickly. so i dicided to use the stickiness with call-ID but still same issue. below is the config
rserver host CIN-VOX-31
ip address 172.20.130.31
inservice
rserver host CIN-VOX-32
ip address 172.20.130.32
inservice
[code].....
Experienced the same sort of behaviour with an ACE 4710 version A3 (2.5). When trying to connect to a webpage on port 443, the pages over 1 minute to download fully. I have timed the download using the plug-in firefox. What is strange is that the browser successfully makes the connection, 200OK etc, but each 'get' takes a very long time to transfer. If I go directly to the server and don't pass via the ACE the page takes between .7 and 1 second to transfer.Is there a way to speed this transfer up, I am currently looking at connection maps.
View 1 Replies View RelatedHow to load balance two/three ISPs using ACE.
What might be the default gateway?Can i create a serverfarm with two rserver with different subnets?
We have two Cisco ACE 4710 and we want to install both of the devices in HA with load balancing mode.While i have done HA mode configuration between ACE 4710.But unable to configure load balancing configuration between them.i want to tell you connectivity between server,client & loadbalancer.Our Web servers are connected to VLAN 152 on the L3 (3750) switch.Which are alreday working in redundancy between other L3.And ACE 4710 it is also connected to vlan 150 which are connected to same L3 (3750) switches and users are also connected to vlan 6 on the same L3 itself.
View 2 Replies View RelatedCan an ACE 4710 have , in the same context - servers which are
a. just being routed to
b. a set of load-shared servers
I have been told you may not be able to do this on this version?
Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later. I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
View 6 Replies View RelatedI am trying to configure ACE 4710 to load balance base on the URL, If it matches the specific URL ( /456/ ), the traffic will be sent to server farm 456 else the traffic will be sent to server farm 123.
I attached an image of the topology.
Ace Config:
rserver host SRV01_123
ip address 192.168.1.101
inservice
[Code].....
I am performing a deployment, in which i require clarity on the following. Our setup has DC and DR , in each site we have two devices for HA.We have received One SSL Certificate from Public CA, Kindly clarify the following doubts i have on thisIn Doc, i found Cert.pem and key.pem is required to generate the pair ,do i receive both Cert.pem and key.pem from the CA or we can generate key.pem from Cert.pem ?SSL Offloading is planned for the X application, and it is running in both DC and DR ( Considering each having their own Public IP address ) , do i need to have two different public certificates or a single certificate can i use in both DC and DR.Load Balancing IssueIs it possible to configure in ACE to access the service in Business hours and in non Business hours to display HTML page showing this is available only during these hours ?In DC we have Three Web Servers ( only in One physical server the service is active, other two are backup ), and these three servers are under cluster and shares one cluster IP , In ACE we have created the VIP and Pointed to only Cluster IP ( like pass through only ). The issue we face is if active web server is down, even then ACE is sending the traffic to that webserver only instead of sending it to the new Active web server. let us know if any solution is there to overcome this issue ?as per my understanding instead of giving cluster IP as real server IP we can issue the three physical servers. now i dont require load balancing between three servers instead require failover king like if first server is down then it should forward to Second server ?
View 4 Replies View RelatedI've done a lot of ACE work over the years but this is the first time this has ever come up.
I have a request from an application group where I have 3 rserver in the server farm but they want all traffic to only go to the first server unless that server fails. If the first server fails, only then do they want traffic to go to the 2nd server instead and if that fails, then traffic goes to the 3rd.
I've read through the documentation but haven't figured out a way to do this. What to do this type of failover configuration?
I'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
[code].....
Our Exchange 2010 hub servers run multiple services/ports: smtp, www, pop3,135, 143, https, 993, 995, 6001,6002,6003,60200,60201,8400, and 8402 what is the best way of balancing these servers so that if only one of the services failed on a server, it would switch only the failed service to remaining servers. At present I only use an smtp probe, so as log as that sevrice is running the server is marked good.
View 3 Replies View RelatedI’m looking for some notes from the field guidance here from those that have much more deployment experience.
I have a GSS and an ACE, and its the ACE that's primarily giving me something to think about, in terms of placement and what mode to adopt.
The traffic flow will look loosely like this:-
Client---Internet---Firewall---GSS---ACE---Servers
Physically, it's like this. The RED line denotes a boundary, and pretty much anything North of that is not accessible to us, we simply have a L3 trunk between our switches and "their" switches (S3/S4) and talk using EIGRP.
There are other servers in the top tier, some that also require load balancing, some that don’t. Typically, I want to load balance HTTPS requests from the internet, to one of the 3 servers in the top half.
I’m not sure what mode to select, routed, one arm? What about placement of the ACE? At the moment, I’ve just configured 1/1 on it and made it part of the MG MT VLAN, it's S VI exists on the S1/S2 switches, so I’m open to change as it's still all in the lab.
Is GLBP(GATEWAY LOAD BALANCING PROTOCOL) Work as a LINK LOAD BALANCER?
View 5 Replies View RelatedCan we monitor context of load balancer using LMS prime 4.2?
View 4 Replies View RelatedI have got Linksys RV082 in my home network to use it as load balancer between 2 providers.Is it possible to make some customisation in scenarioses and logging system? As I understand the device is based on some Linux core and Linux infracrtucture. So it must me available in sources... How I may get this kind of access? I want to get ssh/telnet or other raw access to installed on the device OS and manual control it, treat around web-UI. How may I do it?
View 1 Replies View RelatedReport run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View Relatedi'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?
View 2 Replies View RelatedI have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.
View 1 Replies View RelatedWhat are these ports used for? What can I do with them?
View 2 Replies View RelatedI am trying to configure sticky on an ACE 4710 and don't understand what the netmask part of the sticky ip-netmask netmask address {source | destination | both } name command.
Some examples use 255.255.255.255 and others use 255.255.255.0 but I don't know what the significance is or what it does?
I am going to configure for both source IP and destination IP (both).
With the current (A5) ACE 4710 lic setup, does the "X gigabit per second appliance throughput" that is licensed affect: -
A) Only "appliance" i.e. load balancing traffic, any other normal routed traffic is not included in the limit
or
B) Is it an overall throughput limit on the interfaces i.e. includes all traffic not only load balancing traffic but also normal routed traffic crossing the appliance
Looking at a scenario where the lic size I need for HTTP load balanacing would be one size if A) but would need to be much larger is B) to accomodate out of hours routed backup traffic crossing the ACE 4710
I've just run the ACE 4710 and it seems that is booting up well but it stops when 'Setting up dynamic memory size' message appears.
INIT: version 2.85 booting
b4 lspci
1 Cavium device(s) found.
[Code]....
I've got a web app that the owners want to run over port 80, but also using SSL to secure private data in transit. The architecture is an ACE 4710 in SSL termination mode->Apache (port 2000)->Back-End app server.
I've got two VIPs set up already - one on port 443 and one on 2000 - both of which do the SSL termination quite nicely, but using the 3rd VIP set up on port 80, the connection steadfastly refuses to be HTTPS (i.e. doesn't show the padlock).
I've done all the set-up through the web interface so far, can this be done? If so, how?
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
[URL]
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
View 3 Replies View RelatedI'm receiving a lot of these messages in a ACE4710 cluster. 192.168.100.1:80 is the VIP, 193.126.127.28:56380 is the client. Already tried to set the mss with this:
parameter-map type connection my map set tcp mss min 0 max 1380
policy-map multi-match L4_policymap
class vip_PRDWEB_http
loadbalance vip inservice
[code].....
But it doesn't work.
We have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
View 3 Replies View Related