We have deployed an ACE 4710 and its working perfectly. But the problem is that after I chage the default gateway of the servers I am not able to transfer files from one server to other. Is there any special configuration needs to be done on ACE to achieve this?Other than copy Ping, telnet and everything is working fine from the servers. These servers are in the same subnet & VLAN.
View 3 RepliesI'm setting up an ACE 4710 in our test lab before deploying in production. Do the test web servers I am using need to use the ACE as their default gateway? The are currently configured to use a multilayer switch on their vlan as their gateway but I'm guessing the ACE needs to see the return traffic for load balancing to work correctly?
View 2 Replies View RelatedI'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
[code].....
I'm looking for a way to configure Cisco ACE4710 loadbalancer to bypass traffic that is initiated from server side to Internet?Are there any way to configure this, so that the loadbalancer will not maintain session for this bypass traffic to maximize throughput?
View 1 Replies View RelatedOur Exchange 2010 hub servers run multiple services/ports: smtp, www, pop3,135, 143, https, 993, 995, 6001,6002,6003,60200,60201,8400, and 8402 what is the best way of balancing these servers so that if only one of the services failed on a server, it would switch only the failed service to remaining servers. At present I only use an smtp probe, so as log as that sevrice is running the server is marked good.
View 3 Replies View RelatedI want to transfer big fiiles from PC to another PC, and it has happened frequently, I was wondering is there any way that I can send them directly with high speed if they are connected to the same router (my Router),I got an Desktop with Windows 8 64bit.The target PC (to transfer files) Laptop Windows 7
View 2 Replies View RelatedI have a friend with a mac laptop that I need to transfer roughly ~110 GB from. I have a laptop that dual boots Windows 7 and Kubuntu 12.10. Easiest way to directly transfer these files between our computersNeither of us has a large enough external hard drive.
View 1 Replies View RelatedWan goes down when transferring files between pcs connected to the lan port.It looks like it's running out of resources or something. Passing more than 10GB of data to other pc is a pain in the ass because nobody else can access internet (lan and wireless clients).Filled a support request in local dlink site. No response so far.
Model Dir-600 B2
Firmware 2.05
2 pcs transferring lan data.3rd pc (doing nothing) can't access router config at 192.168.0.1.
I am using csc-ssm module in Cisco ASA 5520 firewall, with the csc version as 6.3.1172.0. I have a public Ftp server and when i ever i transfer the zipped files more than 50 MB or 70 MB or more than that, it fails. I used to upload by clicking the ftp site and copy past the file to the location. After a certain point of time, the download fails with the below error on the explorer.An error occured copying a file to the FTP server. Make sure tou have permission to put file on the server.Details: The operation timedout
Firewall log is below.
ABCFTP1|21|10.120.110.162|1257|Teardown TCP connection 48091783 for Internet:ABCFTP1/21 to XYZ:10.120.110.162/1257 duration 0:00:27 bytes 656 TCP FINs .
-- When i remove the service policy from the firewall, and try to transfer the files, it goes through without any problem. ena
-- Pls check the attached screenshot of the ftp settings in CSC-ssm. There is no problem with downloading files from the server.
I have one machine at office and one at home, both Windows XP SP3, ADSL connection with static IP.On the office machine a have an archive of about 250 GB of files.When i am at home sometimes i need to connect to my office machine, search through those files, maybe preview some, and then download some needed files to my home machine, using a download queue feature is possible.
Radmin
UltraVNC
TeamViewer
p300
DC++ and many variations of it.
Note: am not allowed, and don't want to install any kind or sort of server application on office machine.
Here a have a quest that can't find the perfect solution for a half year now.I have one machine at office and one at home, both Windows XP SP3, ADSL connection with static IP.On the office machine a have an archive of about 250 GB of files.When i am at home sometimes i need to connect to my office machine, search through those files, maybe preview some, and then download some needed files to my home machine, using a download queue feature is possible.The task doesn't seem so complicated, yet, i did not find a perfect simple solution so far.
View 5 Replies View RelatedInternet connectivity on my laptop is lost shortly after beginning to upload/download files over the internet to my cloud storage provider. I also lose connectivity when transferring files to or from the laptop within my LAN to a desktop computer connected via wireless router as part of a workgroup. Connectivity is only restored once I restart the laptop or uninstall, then reinstall drivers for my wireless network card. The issue then reoccurs once file transfers begin again.The laptop is running Windows 7 Home Premium SP1. The driver for my Intel Wireless WiFi Link 4965AGN internal network adapter are up to date. I have a Linksys WRT610N ver.2 router, and an HP Pavilion dv6500 laptop.
View 11 Replies View RelatedI got a refurbished EA4500 (directly from Cisco) last week. I have been having a few issues, which I have found (not too great) workarounds for. However, the latest issue has me stumped, and is unacceptable.Whenever I am transferring files between 2 computers, I get kind of OK speed (5 MB/s). However, while this transfer happens, no other device can connect to the net. Actually, even trying to go to router home page (192.168.1.1) times out.The clients still say they are connected to the router, but I just can't get anywhere.As soon as the file transfer finishes, everything goes back to normal.EA4500 replaced a WRT54G. Never had any problems with that router. It was such a workhorse. Just needed to upgrade to a n-router.I am on the latest non-cloud firmware.I have reduced the MTU size to 1200. Not sure that matters.
View 9 Replies View RelatedOn my moms laptop, (month old Lenovo B570/i3-3230/4GB/W7), when transferring files to my Crucial Gizmo! 16GB USB Drive, it is pretty much impossible to surf the web. Loading websites take 30-60 seconds, it's ridiculous. Is this normal? Her router is Linksys WRT54G. Router is not connected via USB, in fact the Laptop is connected through ethernet cable (not currently using wireless).
View 5 Replies View RelatedWe now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
View 2 Replies View RelatedReport run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View Relatedi'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?
View 2 Replies View RelatedI have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.
View 1 Replies View RelatedWhat are these ports used for? What can I do with them?
View 2 Replies View RelatedI am trying to configure sticky on an ACE 4710 and don't understand what the netmask part of the sticky ip-netmask netmask address {source | destination | both } name command.
Some examples use 255.255.255.255 and others use 255.255.255.0 but I don't know what the significance is or what it does?
I am going to configure for both source IP and destination IP (both).
With the current (A5) ACE 4710 lic setup, does the "X gigabit per second appliance throughput" that is licensed affect: -
A) Only "appliance" i.e. load balancing traffic, any other normal routed traffic is not included in the limit
or
B) Is it an overall throughput limit on the interfaces i.e. includes all traffic not only load balancing traffic but also normal routed traffic crossing the appliance
Looking at a scenario where the lic size I need for HTTP load balanacing would be one size if A) but would need to be much larger is B) to accomodate out of hours routed backup traffic crossing the ACE 4710
I've just run the ACE 4710 and it seems that is booting up well but it stops when 'Setting up dynamic memory size' message appears.
INIT: version 2.85 booting
b4 lspci
1 Cavium device(s) found.
[Code]....
I've got a web app that the owners want to run over port 80, but also using SSL to secure private data in transit. The architecture is an ACE 4710 in SSL termination mode->Apache (port 2000)->Back-End app server.
I've got two VIPs set up already - one on port 443 and one on 2000 - both of which do the SSL termination quite nicely, but using the 3rd VIP set up on port 80, the connection steadfastly refuses to be HTTPS (i.e. doesn't show the padlock).
I've done all the set-up through the web interface so far, can this be done? If so, how?
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
[URL]
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
View 3 Replies View RelatedI'm receiving a lot of these messages in a ACE4710 cluster. 192.168.100.1:80 is the VIP, 193.126.127.28:56380 is the client. Already tried to set the mss with this:
parameter-map type connection my map set tcp mss min 0 max 1380
policy-map multi-match L4_policymap
class vip_PRDWEB_http
loadbalance vip inservice
[code].....
But it doesn't work.
We have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
View 3 Replies View RelatedIf we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
View 2 Replies View RelatedI am new to the 4710 appliance.Apart from the 4 GE 'data' ports, there are 2 Ethernet 'management' ("console") ports. I find the description in the "quick start guide"somewhat confusing. URL, Is a first-time serial connection (at least to run the initial config. script) mandatory? Or can you obtain the same result via one of the 2 Ethernet management ports and using a default ip address (192.168.1.10 ? When running the initial config. script (only possible from the serially connected console i suppose), you have to select your management port. Why does the system in step 5 proposes you 4 ports, and not just 2? I suppose the intended port for management is one of the 2 management ports, not one of the 4 data ports?
View 1 Replies View RelatedI have a pair of ACE 4710s with 12 contexts sharing the load, running A4(2.1). esterday I upgraded one of them to A4(2.3) now I cannot telnet to the Admin context.Pings ok. I can telnet to other contexts on the box and everything seems to be working ok when i do a " sh telnet" comes back with
No Session Information is available
sh telnet maxsessions
telnet maxsessions 16
ACE# sh script code NORDICID_PROBE.Error: Called API is invalid or non-existant.Hardware is ACE-4710-K9 and software A3(2.7)The probe itself is functioning ok according to show probe detail.However show script script_name probe_name -counters all remain at zero for some reason. This wasn't the case on the previously use ACE software.To my recollection the command show script code has worked successfully before on the same ACE software. Not 100% sure though, but it definitely worked on the previous software we ran on the ACE.
View 2 Replies View Relatedthe ACE 4710 is running 3.2.5 and I need to put it in another environment.Is there a way to reset its settings?
View 3 Replies View RelatedAny document that details the steps to change the FT ip addresses of a pair of Cisco 4710 whilst they are running in a production environment without causing an outage?
Would the steps be:
On the secondary unit:
hbs-syd04-lb01ft interface vlan 417 ip address 172.30.254.221 255.255.255.252 peer ip address 172.30.254.222 255.255.255.252
Then on the primary unit:
hbs-syd04-lb01ft interface vlan 417 ip address 172.30.254.221 255.255.255.252 peer ip address 172.30.254.222 255.255.255.252
Or Vice Versa?