Cisco WAN :: Which IOS Is For Router 7606 To Accept FWSM

Nov 10, 2011

I need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.

View 2 Replies


ADVERTISEMENT

Cisco WAN :: PBR Command Not Supported On 7606 Router

Jun 5, 2012

We are planning to configure the ipv6 PBR  on our 7606 routers.  We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
 
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
 
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.

View 1 Replies View Related

Cisco WAN :: 7606-S Router - Replace SUP32 With RSP720?

Sep 29, 2012

I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
 
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?

-are there any steps should i do before the upgrade ?

-i am planning to take the router out of service during the operation, how much down time it will be ?

View 4 Replies View Related

Cisco Security :: 7606 - Unknown Open TCP Ports On Router

Oct 19, 2011

Any know how to close these open ports on my Cisco 7606 router? Any know what these TCP ports are used for?
:
49   - Not sure what this one is other than what IANA reports about TCP port 49
4510
4509
2222
:
I'm sure I could add an ACL to block communications to my router based on this ports but would rather figure out how to close 'em so this already overloaded router doesn't have additional processing.

View 3 Replies View Related

Cisco WAN :: Configure Policy-map With Police Command At Router 7606-S?

Dec 27, 2011

Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
 
[code]...
 
So for egressQOS , i want to configure with police, not shape (for the memory reason).

View 4 Replies View Related

Router Will Not Accept Kodak Printer

Oct 19, 2011

router will not accept kodak printer

View 1 Replies View Related

Printer Will Not Accept Wireless Network Key For Router

Jul 22, 2012

I'm trying to connect my printer to my wireless network via my new Netgear Gateway 7550. The printer will not accept the Wireless Network Key for the router.Had no problem with the old 2Wire gateway.

View 1 Replies View Related

Wireless Router That Will Accept A Usb Dongle Modem?

Oct 25, 2011

I have a three mobile wireless dongle/modem i want to be able to share it, i have found you can buy wireless routers to do this, but they seem to be £60+ because they also contain a mobile receiver transmitter my question is, is there a wireless router, that accepts a usb dongle for the modem connection rather than containing the mobile equipment? which makes it so much more expensive, as the dongle already contains the mobile part anyway tonyuk123 has chosen the best answer to his/her question.Click here to view the answer that was selected.

View 7 Replies View Related

Wireless Router Does Not Accept Subnet Mask

Feb 27, 2013

I am using TP-Link wireless router model no. TL-WR941ND.my isp provided static ip via cable modem.ip = a.b.c.d subnet = 255.255.255.254 = /31 but the router does not support subnet mask saying wrong subnet mask?

View 2 Replies View Related

Set Up TV To Accept Video Media Via W-Fi From DLNA Router From Laptop?

Mar 27, 2011

How can I set up my TV to accept video media via wifi from DLNA router from my lap top?

View 4 Replies View Related

Can't Get Access To Router / Won't Accept Admin Password Or 1234

Apr 8, 2012

I can't get access to my router. Won't accept admin password or 1234 .

View 3 Replies View Related

Linksys Wireless Router :: E3000 FTP Cannot Accept A Log-in From Outer IP

Mar 26, 2011

No Matter what I use-admin/new user or group I assign... CAN NOT login from the outside IP!I can see it/map it and access it all day from my network, no problem. I get at 530 login error everytime I try to come in from the outer world. I have a static IP and cannot get in. It will prompt me for user name and password so I know it is responding to my query. I need to get this fixed ASAP!

View 8 Replies View Related

Linksys Wireless Router :: WRT54G Won't Accept Firmware V4.21.5

Jun 4, 2012

My current unit is at  Firmware Version: v1.02.8 What can I do?

View 3 Replies View Related

Linksys Wireless Router :: EA6500 Won't Accept Connection?

Feb 11, 2013

When I plug in the power cord to my EA6500 all the LED's on the back, and the white Cisco on the front come on solid, then the lights on the back go out and the white Cisco light starts blinking faster than every second. I can't get it to stop blinking no matter what I've tried so far.
 
It won't let me connect to it at all.  I've tried everything I can think of, and have tried almost everything I could find in Troubleshooting in Cisco Community.  The Linksys Smart Wi Fi  Router setup says "We could not find your router."
 
I've also tried using the red Reset button and the light never stops flashing.  I've tried pushing the button quickly, holding it down for ten seconds, and holding it down for more than 30 seconds, but the light continues to blink.  I've also unplugged it and waited more than 10 seconds, but nothing seems to work.

View 2 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3040 Refuses To Accept PIN Code

Dec 11, 2012

Region : Belgium
Model : TL-MR3040
Hardware Version : V1
Firmware Version : factory default / most recent update
ISP : Mobile Vikings

I was configuring a device for one of our customers, but when I was setting up the MR3040's internet connection settings things went haywire.there's only a default selection for two of my country's providers. No biggy you'd think.

View 2 Replies View Related

Cisco WAN :: 2821 Router To Accept 2 Different Incoming WANs And Able To Create VPN Tunnels

Apr 1, 2013

I am currently running a 2821 to terminate vpn links from all our branch offices over a WAN. I need to add a second interface in order to facilitate a move to a different WAN provider. seeing as the 2800 models are EOL I was looking for an upgrade. My local retailer wants to sell me the following:CISCO3925E-SEC/K9 IS Router 3925E security bundle SEC license pack,HWIC-2T 2 port serial WAN card,MEM-3900-1GU2GB Upgrade to 2GB 1,now my question is why can't i use the 2900 models in order to save some money?All I need is a router that will accept 2 different incoming WANs and the ability to create vpn tunnels over them..

View 19 Replies View Related

Linksys Wireless Router :: EA4500 Won't Accept Password / Key For 5g Band

Jul 11, 2012

I just upgraded to the EA4500 for added range, etc. I'd like to let TiVo have the 5g side and use the 2.4g side for everything else. How can I even tell which band TiVo is using?
 
I tried setting TiVo up manually but it won't accept the password/key for the 5g band. I gave up and used the "push button" method, but I have a feeling that puts it on the 2.4g band.I do have two different SSIDs and two different passwords.

View 6 Replies View Related

Linksys Wireless Router :: WRT120N - QOS Doesn't Accept Phone MAC Address

Jan 23, 2012

My Linksys WRT120N router doesn't accept my cellphone's MAC address... Phone's MAC address is AC:81:F3:08:13:F5 but upon adding the MAC address Internet Access Priority Category based on MAC address, I get an error "Assign MAC address is incorrect".

View 1 Replies View Related

Linksys Wireless Router :: Setup EA6500 To Accept FTP Requests To Windows Home Server?

Apr 18, 2013

I am looking at buying the EA6500 router.  However, before I make the investment into buying this router, I need to know some basic information first.

1. I want to setup the EA6500 to accept FTP requests to my Windows Home Server.   Yes or No?
2. Remote access to the EA6500,  Yes or No?  i am aware of the security risks
3. I need to setup Port forwarding on the EA6500.  I assume I can?
4. Manage a Kindle Fire and other wireless devices?

View 5 Replies View Related

Linksys Wireless Router :: E1000 - Reset 4 Times But Not Accept Username / Password Input

Oct 10, 2011

I changed my E1000 router name successfully, and then went into the Administration section to change my password.  After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password.  When I enter the exact same user name and password it does not accept them.  When I try to enter the old user name and password it does not accept them either.  I then try combinations of the two and it still will not accept the input.  I have reset my router 4 times now and this keeps occurring.  I am completely baffled.

View 6 Replies View Related

Cisco WAN :: QoS In 7606 With SUP32

Dec 6, 2011

I need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having  WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations  use to access mail server over the same link.

View 1 Replies View Related

Cisco WAN :: High CPU On 7606-S?

Apr 18, 2011

high CPU on newly installed 7606.
  
CPU utilization for five seconds: 61%/59%; one minute: 62%; five minutes: 63% PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process 578        5856     9392486          0  0.55%  0.50%  0.50%   0 IP SLAs XOS Even 231       90364      576908  

[Code]......

View 1 Replies View Related

Cisco WAN :: 7606-s Is Not Booting

Jan 18, 2013

I tried to reboot manually and I changed the slot but the same behavior:
 
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
 
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102

View 1 Replies View Related

Cisco WAN :: 7606 Interface Configuration?

Mar 5, 2012

who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.

View 1 Replies View Related

Cisco WAN :: High CPU Utilization On 7606?

Sep 28, 2012

Our Router  7606 is in a problem with high CPU Utilization. We are using one EBGP  and one IBGP session. We are also running OSPF with area 0 between two  IBGP router to exchange few local networks. When bandwidth cross 100 MB  than only CPU use become 100%. when bandwidth consumption is 80MB CPU  use become 80% end so on.

Out put is when bandwidth consumption is 34MB
 
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process
  78          44        9625          4  0.39%  0.03%  0.00%   2 Virtual Exec
  13          40         375        106  0.07%  0.00%  0.00%   0 ARP Input
  30         116        1098        105  0.07%  0.01%  0.00%   0 IPC Seat Manager

[code]....

View 27 Replies View Related

Cisco WAN :: 7606-S Planning To Install New IOS

Sep 18, 2012

I have a fresh piece of 7606-S router, i am planning to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router.I have the image on TFTP server.

View 3 Replies View Related

Cisco WAN :: 7606 - Self IP Of Interface Not Pingable

May 1, 2012

I have an Internet Gateway with dual homed to 2 ISP's terminated in 2 different routers in my end. My end routers are 7606 routers.
 
I have a WAN link from Router 1 to ISP1 and from Router 2 to ISP2.
 
Router 1:
-------------
int Gi1/1
description " Link to ISP1"
ip address x.x.x.142 255.255.255.252
 
x.x.x.141 is configured in ISP end router.
 
The problem I m facing is that I m not able to ping x.x.x.142 from this router. But x.x.x.141 is pingable.
 
Also when I check from any internet route server, I m able to ping both x.x.x.142 and x.x.x.141.

View 1 Replies View Related

Cisco VPN :: Installing SPA-IPSEC-2G On 7606-S

Mar 18, 2011

I was trying to install a SPA-IPSEC-2G on 7606-S chassis. I installed the SPI/SPA cards in slot 3, after that I checked with "sh module"  and we could see the module "OK". After this we tried to configure a VPN tunnel but we received messages in the other router about "no ipsec package".
 
I was checking and I tried "sh crypto engine accelerator statistic"  and we got the message:   " There is no crypto device".
 
I don't know about installation commands in references and I don't know about restrictions or configuration modes.

View 3 Replies View Related

Cisco WAN :: 7606 - Tftpdnld Command Not Available

Jul 19, 2011

I have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
 
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
 
How to make the router in running condition.

View 3 Replies View Related

Cisco VPN :: Is It Possible To Run DMVPN On 7606 Without Ipsec Module

Apr 16, 2011

We have  7606 router without any ipsec module on it,so i check the ios and it has all commands in interface tunnel for configuring the dmvpn multipoint tunnel and also protection profile for ipsec! so i have this question: do we can run dmvpn between this router and our wan routers wich are 3845.

View 2 Replies View Related

Cisco WAN :: 7606 Monitor Session Not Working?

Mar 5, 2012

I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything.  Any guess as to why, or what I might be doing wrong?  Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress.  Both source and destination ports are routed ports.
 
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
 interface GigabitEthernet1/1
description WAN Link to *********************  ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252

[code].....

View 1 Replies View Related

Cisco Infrastructure :: PPPOE Gig Subinterface - 15.2S 7606-S

Nov 5, 2012

We have an environment where we terminate our DSL customers over PPPoE on a 7606-S MPLS PE router with RSP720. The PPPoE sessions are terminated on a GIG V2 interface of a SIP-400. Currently the IOS running on the device is c7600rsp72043_rp-ADVIPSERVICESK9-M, Version 12.2(33)SRD. The following is the current configuration used.
 
bba-group pppoe 7virtual-template 7
 
interface GigabitEthernet2/1/3.142647 accessencapsulation dot1Q 14 second-dot1q 2647pppoe enable group 7
 
interface Virtual-Template7 ip vrf forwarding TESTip address 10.10.10.1 255.255.255.252
 
In the  above scenario everything works well.
 
However we had to upgrade the router IOS to    15.2(4)S Advance IPServicesk9 to support 4-byte ASN. After the upgrading we observed certain commands used to terminate PPPoE on the sub-interfaces not available on 15.2(4)S , although  PPPoE on Gig and Ethernet with QinQ support is listed under 15.2S feature set.

View 1 Replies View Related

Cisco Switching/Routing :: Inbound Traffic On 7606?

Jan 17, 2013

I have two Cisco 7606 routers using BGP to connect our customers to the internet.  Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit.  We would like to shift some of the inbound traffic over to the other 7606.  Our Tier provider has the same AS number for both paths.  One path goes directly to New York and the other goes to Boston then New York. 

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved