Region : UnitedStates
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631_V1_130108
Does this modem support NAT Loopback? I can't get it to work.If so, why not, can we have a firmware that supports NAT Loop back?
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631_V1_130108
ISP : iinet
I have set up this modem correctly as it will occasionally sync and internet will be connected for a short time 5-10 seconds then loses sync.Have asked ISP to check line and they say it is fine. I have upgraded to current firmware but same result.I purchased for wireless N and print server features.Have reverted back to 4+ year old Netgear DG834GV which works perfectly with same cabling, filter etc. ISP suggest connect VG3631 on ADSL 1 but if I need to do that I may as well take it back and buy a cheaper wireless AP.I also set my existing Netgear as modem only and connected to EWAN port of VG3631 and it did the same thing (kept dropping connection), this suggests that it is a VG3631 hardware or software problem (completely separate to DSL/Line issues).
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP : TPG
RE: Voice SIP Account Phone Number Not Accepting 2 Characters My ISP TPG VoIP SIP account phone number is my TPG username rather than an actual normal telephone number. When I enter my 2 characters TPG username 'xx' as my TPG VoIP SIP account phone number as the 'Phone Number' field in the 'Voice - SIP Account' modem router management page on the LAN IP 192.168.1.1, then I press the 'Save' button, I encounter the error message "The length of 'Phone Number' is out of range[3,32]."I believe this error is due to my TPG SIP account Phone Number’ is not within the TD-VG3631 ‘Phone Number’ character length range from 3 to 32 inclusive.My old modem can register to my TPG VoIP account successfully with my TPG username 'xx' as the VoIP SIP account phone number.
I have contacted my ISP TPG and tried to get an actual VoIP SIP phone number. However, TPG does not provide an actual VoIP SIP phone number to their customers. TPG states I should use my TPG username as my VoIP SIP account phone number. They ask me to contact TP-Link to resolve the aforementioned error.Is there a way I can enter only 2 character TPG username as my VoIP SIP account phone number in the browser management page of the modem router? i.e. workaround, request TP-Link for a new firmware fix or else?
Region : France
Model : TD-VG3631
Hardware Version : V1
Firmware Version :
ISP :
I tried to upgrade a TD-VG3631 that came with firmware version TD-VG3631_V1_120929 to the latest TD-VG3631_V1_130108 version.[url]...Is there a recovery procedure to flash back a firmware?
-Region : Spain
-Model : TD-VG3631
-Hardware Version : V1
-Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up.And when I call, I can see in the log the INVITE action.
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version :
ISP : Engin
i purchased this new modem TD-VG3631 to replace my old one, Finished the internet configuration, it's ok, i can go to internet smoothly. however when i configured the voip function, i encountered a big problem, even i have entered all info which provided by Engin into your modem, it doesn't work. the status always down..Very sure it is not my account problem, because if i enter these info into my old modem , it works very well.
[code]...
Region : Spain
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP :
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up And when I call, I can see in the log the INVITE action :
32013-03-19 10:16:33OTHERDebugport 1 cx 0x3, evt/reason 3/0 buf (nil)
42013-03-19 10:16:01OTHERDebugport -1 cx 0x3, evt/reason 1/4 buf 0x4761a8
52013-03-19 10:16:01OTHERDebugthe initial INVITE request for [accIndex(0),callIndex(3) dest(<sip:103@192.168.1.254>)] is sen
But I�am sniffing traffic in the PBX and not received the invitation... Obviously the 103 station never recive the call...I think that maybe the INVITE is going out behind the WAN interface.... bug version?
When can we have an upgrade to include 'Lookback' function for Virtual Server ? I understand both Build-120802 and Build-120926 does not support this Loopback feature. Without the loopback feature, we won't be able to test out Dynamic DNS URL is working or otherwise on local PC.
View 1 Replies View RelatedRegion : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
I have a problem in the model TD-W8968 of modem.Wireless abruptly stopped Even works must turn off the modem Malk happens sometimes 3 to 5 times
Region : Canada
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Bell Canada
Can I use TD-W8960N an additional router with my ISP bell router. Will it increase my speed and range of internet in my home.
Region : Egypt
Model : TD-W8961ND
Hardware Version : V3
Firmware Version :
ISP :
my router is placed in my home. i want to access to it with IE from my office.but no luck.also i try to ping the WAN ip address of the router.
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : not clear
Firmware Version :
ISP : BT
I am thinking of buying a TL-WDR3600, but just need to know the answer to the question below.Can anyone confirm if the TL-WDR3600 supports NAT Loopback functionality?
Region : CzechRepublic
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : Ufon
I have a modem ANY DATA ADU-520L and I would like to know whether you are considering supporting this modem in your router?
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : Airtel-4G
using ZTE MF 880T LTE modem and TL-MR3220. I am not sure whether TL-MR3220 supports ZTE MF 880T.
Region : Finland
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 rel.577775n
ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies View RelatedI have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
I plan on moving to a new internet service provider within a few weeks time, and I have a question.I'm going with TekSavvy, and they have a DSL plan which is quite worth it, and I'm in need of a modem when I make the switch. I think I made up my mind on which modem I want, but I just need to know.. can I use ADSL2+ on the DSL service I am going to get?If you need to know what modem I'm going for, I'm going with "TP-LINK TD-W8960N, 300Mbps Wireless N ADSL2+ Modem Router"
View 1 Replies View RelatedRegion : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."