TP-Link ADSL2+ Wireless :: TD-W8970 Wireless Connection And DHCP Server
Feb 27, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
View 5 Replies
ADVERTISEMENT
May 7, 2013
Region : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I am struggling to get a printer added through the print server. The printer is set up in the TP-Link USB Printer Controller and selected as the auto-connect printer. I can scan through the server, but can't add the printer in control panel or see it as a option when printing. The printer is a Samsung SCX-340F.
View 2 Replies
View Related
Feb 28, 2013
Region : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
View 3 Replies
View Related
Feb 25, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
View 5 Replies
View Related
Apr 16, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
View 2 Replies
View Related
Mar 24, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Infostrada
My TD-W8970 freezes randomly, sometimes several times a day, sometimes less, but now the problem it's more frequent and I suppose it could be generated by some internal component that could have a abnormal behavior.Anyway, this happens in different situations, either using all the functionalist, or being only on and in idle state. Last time was few minutes ago, when all the system were shuttled down and only router was on.
View 1 Replies
View Related
May 4, 2013
Region : Others
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
I just set up DDNS for my home, and also set forwarding port 5000 for my NAS with an specific IP address 192.168.1.xx. Then, I use my office Internet to call DDNS xxx.dyndns.org:5000 to connect the NAS in my home, It is working OK (from outside to home) However, if I call xxx.dyndns.org:5000 by my home Internet, it is not working (from inside home to home). But if I directly call NAS' IP address 192.168.1.xx:5000, it is OK to reach it. So I think, DDNS used behind TD-8970 (inside home) is not working. TD-9870 is not forwarding port.
I don't know what do I miss in setup this WD-8970.
My previous Zyxel wireless router modem can allow me to us DDNS behind it with out any extra setting. Is it possible that there is still some bug in Firmware of this TD-8970?
View 4 Replies
View Related
Apr 12, 2013
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
View 1 Replies
View Related
May 3, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
View 1 Replies
View Related
Apr 15, 2013
Region : United Kingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : O2
I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.
Please see the text below.........
I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.
I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.
I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.
There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.
View 6 Replies
View Related
Mar 4, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom
Below you point out my attenuation values detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
View 3 Replies
View Related
Mar 3, 2013
Region : UnitedStates
Model : TD-W8970
Hardware Version : V1
ISP : CenturyLink
Just installed new W-8970 via centuryLink ADSL, connected two computers (hard wire) which work fine. I also have it connected by hard wire to my Direct T.V DVR Model HR 24 to run T.V app's such as Pandora music etc. It will only stay connected for 5-10 minutes then drops out, any suggestions other then buying a different brand modem/router.
View 1 Replies
View Related
Mar 13, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
View 2 Replies
View Related
Mar 7, 2013
Region : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I am trying to get a windows 7 laptop to connect to a TD-W8970.
View 1 Replies
View Related
Nov 15, 2012
Region : Thailand
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 2.0.0 Build 111111 Rel.1111
ISP : 3bb
I have a problem when I am trying to add another static ip address to the list
the message above in title pop up, how can I fix it?
DHCP Table is Full!
View 1 Replies
View Related
Feb 25, 2013
Region : Australia
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N_V4_130205_Beta
ISP : TPG
I have an Optus Home Zone (mobile cell tower) that requires ports open.
Port
123 UDP
500 UDP
4500 UDP
I have assigned the Home Zone a Static IP outside the DHCP range and set the above Ports on the NAT, Virtual servers to that IP address.
I have used nmap to scan the ports and it provides open/filtered status for all of them.
Here is the kicker for me, i use a DGN3500 netgear (which keeps dropping WiFi hence its replacement) and enter the ports and it works straight away. Un plug and put the Tp-Link and nothing.
I use Eset Smart Security, could that be the problem?
View 1 Replies
View Related
Dec 3, 2012
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
View 2 Replies
View Related
Mar 3, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
View 1 Replies
View Related
Apr 9, 2013
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
View 1 Replies
View Related
Nov 8, 2012
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
View 2 Replies
View Related
Mar 22, 2013
Region : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
View 2 Replies
View Related
Jan 28, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 120926
ISP :
Is it possible to turn off the web server facing the internet. When accessing my external ip address I am presented with the logon banner requesting user name and password together with the TP-Link name and model numbers. I would much prefer if I could switch this access and banner off.
View 4 Replies
View Related
Apr 14, 2013
Region : Ireland
Model : TD-W8980
Hardware Version : V1
Firmware Version : 0.6.0 0.6 v000 build 130303 rel. 38108n
ISP : Eircom
Bought this adsl router on Friday and since then I have been experiencing random frequent wireless dropouts, router appears to reboot at this point too, Internet drops out too. Wireless drops as I hear the beep from my airplay speaker reconnecting. Any one have these issues too, tired changing channels, then back to auto again, still no joy.
View 4 Replies
View Related
Mar 7, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 1.0
ISP :
I recently bought this modem for use at home. When I try to log in to my computer at work I am able to log in to the server via a VPN connection but not onto individual computers via Remote Desktop Connection. Both computers run windows 7.
View 4 Replies
View Related
Jan 23, 2013
Region : UnitedStates
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.10 v0005.0 Build 120516 Rel.45877n
ISP : HiPointInc
Network Status.jpg
I've upgraded my line connection from 4mbps to 20mbps.I've also checked my status with HiPoint and on 192.168.1.1 which is shown on the attachment. No problems.
Max Downstream is 25612kbps but Current is only 4396kbps.Do I need to configure anything? Btw its directly connected to my PC?
View 2 Replies
View Related
Jan 23, 2013
Region : Australia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0
Build 120926 Rel.27100n
ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
View 2 Replies
View Related
Feb 24, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
View 1 Replies
View Related
Jan 1, 2013
I have two WAP321s in my office. The network they are on is a single VLAN (172.16.10.x). Both WAPs are setup with the same SSID, and I have setup Single Point Setup.
I am having a problem that was happening before I setup Single Point Setup, and it is still happening. Basically wireless will be up and running fine for part of the day. Then people throughout the office will begin to lose their connections to the DHCP server. They still retain the connection to the WAP, but can no longer access the network.
The only way I have been able to fix this issue is to reboot the WAP. As soon as it reboots the connections come back. At first I thought it was due to the number of connections (which is why we now have 2 WAPs), however we only have about 20-25 conncurrent connections.
I put in the second WAP to try to balance out the load but this does not seem to be working. Is there a setting I need to change on the WAPs to balance out the load?
View 13 Replies
View Related
Feb 16, 2011
Started this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
View 3 Replies
View Related
Nov 29, 2012
I have DIR-601 wireless router with two computers connected: Server (192.168.1.2) and Client (192.168.1.3 on Ethernet Port and 192.168.1.4 on Wireless)
I also use dlinkddns.com and my router's public IP is mapped as abc.dlinkddns.com.
In the router Virtual Server section, it is configured as:
Public Port: 3389 (for Remote Desktop)
Private Port: 3389
IP Address: 192.168.1.2 (server's IP)
I am expecting this to allow the client to access the server via windows Remote Desktop.
The current situation is:
- When wireless is on, the client can access the server's Remote Desktop
- When wireless is off and client is connected by wired Ethernet, the client cannot connect to the server's remote desktop. After timeout, the error msg is "Remote Desktop can't connect to the remote computer for one of these reasons: ...".
- When the client is in another network, it can connect to the server through the Internet.
I am sure it's not the client's problem because it can access via wireless or remotely from another network. It's not the router's virtual server config problem for the same reasons. Will it be a bug in the router? (hardware version: B1, firmware version: 2.00NA).
View 1 Replies
View Related
Jan 19, 2013
Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.
I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.
DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.
View 4 Replies
View Related
Apr 17, 2013
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
View 1 Replies
View Related
Jan 12, 2013
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
View 1 Replies
View Related
