Linksys Wireless Router :: E3000 Unplug Modem Power And Tv Cable
Nov 25, 2011
i have an e3000 linksys cisco router. i havent had any problems before until i tried adding a new computer via cat5e ethernet cable. The first computer always is connected fine whether i unplug the router or modem in any order and replug. i dont know much how to fix this. ive tried some unplugging method once but it only worked until i turned the computer off and back on later. i am also running 2 xboxs with no trouble. i used cisco connect to diagnose problem but it just told me to unplug modem power and tv cable and i did that with no luck.although i have good equipment, the internet is pretty slow.i have the best service of my provider that states it has upto 50 mpbs download speed.i ran the cisco internet speed test and only got a max of 20 download and 5 upload.how could i speed this up?
View 9 Replies
ADVERTISEMENT
Aug 28, 2011
Upgraded my E3000 from 1.0.02 to 1.0.04 and now I cant get an ip from my arris modem. I did the 30/30/30 reset and everything but no luck. I've had to plug the modem directly into the computer for now. Where can I find the 1.0.02 download or how can I fix this?
View 3 Replies
View Related
Jun 30, 2011
I've had my DIR-601 for almost a year now and it's been working near flawlessly until just recently. I have a very simple setup with a desktop PC, router, Time Warner cable modem, and the only device that accesses the router is my Droid phone. I shut my PC down every night. The next day when starting up my PC, there's no internet connection. I haven't fooled around with any router settings, but what I've been doing to re-connect is unplug the cable modem power cord and router power code, wait a minute, then re-plug them back in and it connects right away. Is there something easy that I can do/repair to correct this? Maybe I should check if there are firmware updates?
View 1 Replies
View Related
Nov 6, 2010
The power light keeps flashing. I tried to download the firmware, but when I click on the link it says the page cannot be found.
View 9 Replies
View Related
Aug 20, 2011
I just bought this Linksys E3000 high performance router and all it does is have the LED Power light flashing constantly. I've tried resetting it and leaving it unplugged for a few hours but nothing works. When I try to use the installation software it gets to 25% then says it couldn't find any network
View 9 Replies
View Related
Mar 4, 2012
I have a cisco E3000 with firmware version 1.0.04. I enabled the Local Management Access with HTTPS. If I connect to the HTTPS management interface, I can see that the date of validation of the HTTPS certificate is valid.If I disconnect completly my router (disconnect the power supply), it seems that the HTTPS certificate is regenerated for the boot. The problem is that it is regenerated with a validation date from 01/01/1970 to 01/01/1971. I guess that the certificate is generated before the router is able to automatically set its own time.
View 2 Replies
View Related
Dec 12, 2011
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies
View Related
May 22, 2012
I use a modem d-link DWM 152,,at first be detected, was able to browse. connect the modem still keep fit (I forget if it still connect.), I just unplug it. when i plug it in again, the modem is not detected.
View 1 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Jan 11, 2013
how to i connect mu linksys router to my ubee cable modem
View 2 Replies
View Related
Jun 10, 2011
Our router is connected through a cable modem and If I connect my computer directly wired to the cable modem, I have no problem, it does not disconnect at all.In comes the router in between, when I connect the router and connect my computer through the router WRT54G2, it works initially then I get disconnected after about 1-2 hours. This is very regular. I have a temporary solution by resetting the router via two ways:
1. Go to the admin page, and perform a release and renew IP method.
2. Simply power off the router and then on again.
View 3 Replies
View Related
Feb 24, 2013
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
View 9 Replies
View Related
Sep 27, 2011
I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.
View 1 Replies
View Related
Feb 20, 2013
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
View 6 Replies
View Related
Apr 9, 2013
Reset to factory defaults. DHCP turned on. Status page shows black for router IP, gateway, and DNS addresses. Powered router+cable modem on/off multiple times already. I also have another wifi router (WRT120N) and it works fine.
Pretty simple connection. Just a ethernet cable between the cable modem and E1200 internet port (Cable modem <---> E1200)
View 2 Replies
View Related
Jan 12, 2010
I have a need to have 2 seperate networks from my comcast cable modem.I was hoping to plug a 5 port hub into the cable modem and then plug both the wrt610n and the wrt54g into the hub. Seem that only one of the routers will get an ip assigned from Comcast.Is there a way to have one ISP cable modem and create two different home networks with the two linksys routers, thus two separate independent networks?
-Network 1: public household use and family (Jane's wireless laptop, household PC's etc).
-Network 2: private household/company use and separate from the public family network (company wireless laptop/company PC, un-secure media server).
View 7 Replies
View Related
Jan 14, 2012
I am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
View 2 Replies
View Related
Aug 26, 2012
I just switched to Roadrunner Lightening via Brighthouse Networks. There is no configuration capability in the Cable modem/ router / wireless - Ubee provided to make the Modem a bridge. You have to call Brighthouse to do that. They indicated that they only do that for supported routers and the EA 4500 is not one of them. I'm ready to call them to say I have one of the supported modems so "do it" and then find out what happens.
Meanwhile I have connected my EA4500 through their router and have a network in a network. I've noticed another more significant problem. The speeds through the EA 4500 drop to 90%. Is there something wrong with the router configuration that would cause this significant drop in speed? I'm afraid if the problem is the EA 4500.
View 2 Replies
View Related
Mar 6, 2013
We have a E3200 wireless router but our only connection is wireless. There is no Ethernet connection or cable modem. Presently I am unable to bring up the web page ie...10.100.x.x for entering the id/pw to login. Router is setup with default settings. Is there a setting that needs to be changed from the setup menu or this type of setup will not work with this router.
View 9 Replies
View Related
Sep 26, 2012
Attempting to get EA6500 working with TWC Motorola Surfboard SBV5220 modem, which has been working just fine for the last 2 years with a Linksys E3000 router. DHCP client in the EA6500 either doesn't ask for an IP address from the cable modem or the modem just isn't supplying one. With the E3000, you could see the IP address assigned by the cable modem and the primary and secondary DNS server addresses provided, and if the DHCP request didn't work, these addresses would be all zeroes. But, with the EA6500, I can't find an equivalent screen that shows these assignments, or zeroes when the DHCP request fails.
View 1 Replies
View Related
Mar 7, 2007
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies
View Related
Apr 5, 2013
I cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?
View 9 Replies
View Related
Feb 5, 2013
I am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection. If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.
View 4 Replies
View Related
Jun 10, 2011
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies
View Related
Sep 20, 2012
i have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in
View 1 Replies
View Related
Jan 18, 2012
I have DOCSIS 3.0 modem and a Linksys E1000 wireless router with which I get reults from SpeedTest of 8.6 mps down, 1.57 mps up up from 15 mps service from cable provider. Connected to modem via ethernet cable produces 16.0 speeds. Do I need to upgrade the router or are my settings wrong?
View 1 Replies
View Related
Mar 6, 2011
I want to get a Linksys E3000, mainly because it stomps all over the competition in this bracket for wifi throughput.But I have forgotten how to set up the DG834G to act as a modem for the E3000 going from the DG's LAN port to the E3000's ethernet WAN/Internet port?
View 5 Replies
View Related
Jun 25, 2012
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies
View Related
Apr 15, 2013
I have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
View 1 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
Jul 8, 2012
I recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies
View Related
Mar 23, 2011
Is there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies
View Related
Dec 13, 2012
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
View Related
