D-Link DIR-601 :: Must Unplug / Plug Back In Cable Modem
Jun 30, 2011
I've had my DIR-601 for almost a year now and it's been working near flawlessly until just recently. I have a very simple setup with a desktop PC, router, Time Warner cable modem, and the only device that accesses the router is my Droid phone. I shut my PC down every night. The next day when starting up my PC, there's no internet connection. I haven't fooled around with any router settings, but what I've been doing to re-connect is unplug the cable modem power cord and router power code, wait a minute, then re-plug them back in and it connects right away. Is there something easy that I can do/repair to correct this? Maybe I should check if there are firmware updates?
View 1 Replies
ADVERTISEMENT
Nov 25, 2011
i have an e3000 linksys cisco router. i havent had any problems before until i tried adding a new computer via cat5e ethernet cable. The first computer always is connected fine whether i unplug the router or modem in any order and replug. i dont know much how to fix this. ive tried some unplugging method once but it only worked until i turned the computer off and back on later. i am also running 2 xboxs with no trouble. i used cisco connect to diagnose problem but it just told me to unplug modem power and tv cable and i did that with no luck.although i have good equipment, the internet is pretty slow.i have the best service of my provider that states it has upto 50 mpbs download speed.i ran the cisco internet speed test and only got a max of 20 download and 5 upload.how could i speed this up?
View 9 Replies
View Related
May 22, 2012
I use a modem d-link DWM 152,,at first be detected, was able to browse. connect the modem still keep fit (I forget if it still connect.), I just unplug it. when i plug it in again, the modem is not detected.
View 1 Replies
View Related
Feb 4, 2012
How do I plug the wireless router to the cable modem?
View 1 Replies
View Related
Dec 18, 2011
I have not yet hooked up my router, N150. What I would like that after I hook the router up and then deside I don't want to use it. How do I disconnect it and go back to using my DSL modem and being connected to the internet?
View 3 Replies
View Related
Apr 27, 2013
I have a Linksys WRT54G2 v1 router which is having a daily problem of connectiing to the Internet on my home wireless LAN. My temporary solution is to disconnect the power from the router for about 15 seconds and plug it back in .... and all is well.... at least for another day or so.The real problem is that instead of properly connecting to IPv4 address 192.168.1.100 ..... it randomly connects to Autoconfiguration IPv4 address 169.254.29.54 When this problem occurs the SSID list shows both my 192 connection as well as a public network with no Internet connection?
I've used this router for several years without a problem until I recently bought a new Canon wireless MG5320 printer which initially had problems connecting to my LAN. After a telco with tech support the printer works fine but now I am now experiencing the Autoconfig address problem.My LAN consist of the WRT54G router, a Motorola cable modem, a Lenovo laptop running Win7 64bit, a Hp desktop running Win7 64bit and the Canon wireless printer. (all connected wirelessly)
View 2 Replies
View Related
Feb 26, 2013
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
View 4 Replies
View Related
Sep 6, 2011
I have a network set up currently with a cable modem that goes into a router, the router then goes to a 16 port switch and the switch goes to computers, printers, and my server. I am trying to figure out how to make the modem plug into the switch instead of the router. I'm guessing my problem lies with the default gateway since that is the router. Any suggestions on this? Or how is the best way to set this up? I have 2 NICs on my server and the server has windows 2008 r2.
View 6 Replies
View Related
Jun 20, 2011
My modem does not have a Ethernet plug in for my router. do I have to buy another modem for a 2nd computer?
View 1 Replies
View Related
Jan 24, 2013
How do I hook up a Belkin 750 Router to my modem when modem has only one plug?
View 1 Replies
View Related
Jan 6, 2011
This modem has only three ports. How can I plug in an Ethernet cable and a phone cord cable?
View 1 Replies
View Related
May 26, 2007
I have a WCG200 v1, and lately it keeps reseting, so I started thinking maybe it's a power problem. I go to unplug it, and the power plug is extremely hot, so we unplug it, and let it cool off, then plug it back in later. It works fine, and we go to bed, I wake up this morning and it's back to very hot again..
View 2 Replies
View Related
Jan 13, 2011
i just got a couple of these units delivered but have problem. the power supplies (j8712a) have this plastic insert key between the 3 prongs in the female connection. The cheapest nema 5-15p to iec c15 power cable I found in usA coincidentally is through hp for $23.75usd plus shipping (hp part 8121-0973): [code]
View 3 Replies
View Related
Mar 6, 2012
What is the correct polarity of the power input plug for vigor110 modem?I know it should be 9volts but which part of the plug should be positive? Original power supply gone missing and no indication on unit of plug setting.
View 5 Replies
View Related
Jan 1, 2013
I have a Belkin usb adapter to pick up my wireless internet. problem is when i choose my network to connect to it constantly says "acquring network address". But as soon as i plug in an ethernet cable from the router the wireless starts working and i just unplug the ethernet cble. So why does my wireelss card depend on my ethernet conenction?
View 7 Replies
View Related
Jun 6, 2011
i'm trying to connect to my wii n my laptop. i have a cricket broadband hookup to desktop.
View 1 Replies
View Related
Nov 20, 2011
I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies
View Related
Jan 9, 2013
I've had a dlink604router connected to a dsl modem for the longest time with all my computers receiving internet without any problems. I just switched to a cable modem and the router blinks as if it's communicating with the modem but no internet is getting to the computers connected to the router. I've always left the dlink's settings to default-my 2 macs receive automatic dhcp. If the settings on the dlink have to be changed to communicate with the new cable modem?
View 7 Replies
View Related
Feb 13, 2012
I've been trying to connect my D-Link DIR-601 router with a Motorola SBG901 cable modem. The modem itself has a built-in WIFI (G) and one ethernet port, but not good enough for my purposes. I need more wired connections and an (N) WIFI connection, which the D-Link could provide, if I could get it to work. I just cannot get the two pieces of equipment to talk to each other. I can set up 2 independent LAN's, but no WAN (internet connection) from either. D-Link has provided pages of instrutions, but nothing works.
View 1 Replies
View Related
Jul 21, 2012
We ran a D-Link DIR-655 for about 5 years on our home network of 7 desktop computers (LAN) and two laptops (wireless) with essentially no problems. However following a power outage last week the router stopped communicating with the cable modem (WAN port failure?). From the web site we determined that the DIR-825 is a fancier version of the DIR-655 (extra 5 GHz transmitter) so we upgraded to a new 825 three days ago. I did not use the wizard on the CD to set up the new router -- rather did it manually because I thought I'd configure the new router exactly the same as the old one -- this was probably not a good idea in retrospect. (FYI our new DIR-825 is a ver. B1 unit with ver. 2.02NA firmware.
After setting the router up -- it lit up like a Christmas tree and I could see all 7 desk top computers (3 are WIN7 & 4 are WINXP) in the LAN and all would go on-line with no issues. (FYI 3 desk tops are directly attached to the DIR-825 and four attached via a switch). However, when I tried to map the network I find that only 5 of the desk tops we assigned to our named home network -- 2 or them could not be mapped as they were assigned to a "public" network. So while they all still communicate with each other two are no longer in our home network. I do not think this was anything that I did -- knowingly at least.
I logged back on the the router home page but I see nothing that clues me in as to what I did wrong.So I'm wondering how the DIR-825 made these "assignments" and what I can do to redirect the router to bring the other two computers into our home network. (BTW one of the two "miss-assigned" computers is WIN7 and one is WINXP so its not a window version issue).
View 2 Replies
View Related
Apr 7, 2013
We have kids in the house and I'd like to limit their internet access to certain times of the day but because of the great amount of devices they use (phones, tablets, laptops, etc.) the only way I could think of doing that easily was to set up two wireless networks: one that the adults could use 24/7 and the other that the kids could access during certain set hours.
Here's the equipment I'm working with:
DLink DIR 615 wireless router
DLink DIR 515 wireless router
Motorola Surfboard cable modem S85101U
I plugged the DLink 615 in, set it up for DHCP client and plugged it into the cable modem. I lef the default 192.168.0.1 IP address for the device. On that router, I also reserved the 192.168.0.199 IP address and assigned it to the DLink 515.I also gave the DLink 515 device the IP 192.168.1.1 so I could administer it.I set the DLink 515 to static IP and made the IP 192.168.0.199 and the default gateway 192.168.0.1.I plugged the DLink 515 into one of the LAN ports in the DLink 615.I set a schedule on the DLink 615 to shut down internet access to the DLink 515 at a certain hour and turn it back on at another time.Everything seems to work ok, but at least once a day we have to unplug and plug the routers to reset them.
View 1 Replies
View Related
Feb 8, 2012
my dir-655 rev. A2 router won't connect to the new modem that Charter sent me. I had the scientific Atlanta model dpc2100r2 modem but Charter called and said that they have upgraded my speed for free from 18/2 to 30/4 and that I needed a new docsis 3.0 compatable modem in order to take full advantage of the speed upgrade. I received the modem and connected an activated it according to their instructions. The modem works fine when connected to the PC only but as soon as I connected to the dir 655 the link light went out on the modem and I lost my internet connection. The first step I took was to clone the mac address in Wan section of router. It still did not work. The next step was to turn the modem off, the router off and shutdown the PC. I waited until this morning to reconnect everything. I started the PC, then I started the modem and waited for it to stabilize and finally I restarted the router. I still had no connection. The status page of the router said that the cable was disconnected and that network was disconnected. There was no info to release so I clicked the renew button but nothing happened.
View 3 Replies
View Related
Feb 14, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : charter, its smarter.
so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.
View 1 Replies
View Related
Mar 29, 2013
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
View 3 Replies
View Related
May 7, 2013
I just replaced my DIR-655 with a DHP-1320 since the constant microwave usage in our house whacks out our wireless during breakfast and dinner time. Now the PCs on the other side of the house are connected over a Home-Plug network.Is there a way to connect the DIR-655 to one of the Home-Plug ports on the distant side of the house to "extend" the wireless coverage there for our laptops? Presume this is a different scenario than creating a "bridge", "access point", or "extender" since the router would be connected back via Ethernet cable. There may be some overlap too in wireless coverage around the middle of the house. Ideally I'd like to use the same SSID.Has this ever been done before? What would I need to reconfigure on the DIR-655?
View 5 Replies
View Related
Nov 19, 2007
I have a BEFCMU10 v1 that has been misbehaving recently. It will go off line losing contact with the router and the Internet. It will stay off line for 8 to 10 minutes and then comeback on its own. If I cycle the power it will come up pretty quickly. Here is a log of a recent episode without power interruption.; [URL] Is there a solution or is it time for a new modem?
View 9 Replies
View Related
Jun 3, 2013
I have a Netgear ADSL2 router connected to my main computer and want to add a new Belkin AC900db via plug link at the other end of my house so that we have wireless coverage throughout the whole house. It was working at first but the belkin needed an update which I did now It won't work at all?
View 3 Replies
View Related
Mar 13, 2011
I have an older (but still good) computer...it's gotten to the point of being somewhat less than functional due to remnants of old programs and viruses and such scattered thoughout it. After a few weeks of fighting it to get it to run properly I think at this point my best option is to reformat the hard drive and re-install the original OS from CD. I've already backed up all my important files to CD and DVD, pretty much ready to pull the trigger here.... Concerned about getting back online! I have cable internet (Bresnan)...I want to make sure I have the proper drivers and any applicable software to get back online, I know people have had problems with this after reformatting....The computer is a dell dimension 8400, I'll be returning it to a windows XP home edt. with sp2 from the OS CD, (circa 2004ish). I plan on putting a comodo firewall installation on a CD as well, so I have a functional firewall in place (instead of the crappy norton one that will get re-installed) when I go to get the sp2 updates and the sp3 and updates and not just end up re-infected again...
View 3 Replies
View Related
Feb 20, 2013
How can I configure Belkin N1 Vision Modem router to use Back to My Mac? Bcos in iCloud preferences its give me a error message "setup router for better performance"
View 2 Replies
View Related
Jul 4, 2012
How to create loopback cable for gig copper port (cisco 6513).I
View 3 Replies
View Related
Jun 15, 2012
We have multiple cisco cat 2900 switches. all switches don't have cascade cable port in back panel. i want some sort of solution to manage those switch remotely.
View 9 Replies
View Related
Dec 13, 2012
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
View Related
Apr 23, 2013
With this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies
View Related
