Linksys Cable / DSL :: WCG200 Power Plug Getting Very Hot?

May 26, 2007

I have a WCG200 v1, and lately it keeps reseting, so I started thinking maybe it's a power problem. I go to unplug it, and the power plug is extremely hot, so we unplug it, and let it cool off, then plug it back in later. It works fine, and we go to bed, I wake up this morning and it's back to very hot again..

View 2 Replies


ADVERTISEMENT

Special Power Cable Plug For Switch 5400zl?

Jan 13, 2011

i just got a couple of these units delivered but have problem. the power supplies (j8712a) have this plastic insert key between the 3 prongs in the female connection. The cheapest nema 5-15p to iec c15 power cable I found in usA coincidentally is through hp for $23.75usd plus shipping (hp part 8121-0973): [code]

View 3 Replies View Related

Linksys Cable / DSL :: WCG200 Bridge Mode From Wireless-G Cable Gateway To Wired?

Mar 14, 2013

Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:

- WLAN AutoConfig service has successfully stopped.Wirel?

- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll

- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.

- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down.  Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]

Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.

View 9 Replies View Related

Linksys Cable / DSL :: WCG200 Wireless Is Not Working?

Jul 1, 2009

I have the WCG200 and it has been working fine with my Comcast service for the last 4 years with no issues, either wired or wireless.  Starting about a week ago, I have been having a lot of trouble with my wireless.   I am on Firmware Version: 2.0.3.9.31-1023 and my ISP is Comcast.  I have tried calling Comcast to see if there is a firmware update but that phone call usually doesn't go very far.

View 8 Replies View Related

Linksys Cable / DSL :: How To Setup Password WCG200

Jan 31, 2008

How do I set up a password to secure my home wireless network. Gate is on a XP desktop. Just have my Vista notebook on network. Use WCG200 gateway which was given to me by relative who has upgraded.

View 6 Replies View Related

Linksys Cable / DSL :: WCG200 Factory Reset?

Apr 26, 2012

If I use the reset on the back of the WCG200 and reset it to the original factory settings, does the firmware version revert to the original version?

View 2 Replies View Related

Linksys Cable / DSL :: WCG200 Eventually Loose Connection

Jan 18, 2012

I'm having a problem with my WCG200 wireless gateway.  I can sucessfully use it to connect to the internet using the wireless feature but only for a short time (10-30min at a time). Eventually, I loose the connection.  I'm not sure if it's a modem issue or an ISP issue but only one of my two laptops has this trouble.
 
 Symptom: Connecting with a Dell Lattitude E5520 laptop It works normally until the "US" and "Online" LEDs turn off and only the DS light is left blinking. At that time I no longer have a connection to the internet.  Once I cycle power on the WCG200 it re-connects and works for a while, then the same issue repeats. I cleared the modem log and let the failure occur again to record the fresh log. 
 
 I attached the Modem Log in case that would troubleshoot. I've got the security of the modem set to allow the laptops MAC addresses and using WPA-personal / TKIP encryption. I never had this problem until I started using a new laptop,  I'm starting to suspect that my ISP is disconnecting that laptop for some reason ?

View 3 Replies View Related

Linksys Cable / DSL :: Installing Vista Drivers For WCG200?

Mar 25, 2007

WCG200?i have just bought a new laptop with Vista Home Premium as the OS.i've already downloaded the new driver file, and unzipped it. but how to i install it so that i can get online wirelessly?all my permissions are set properly to allow communication, but i cannot get onto the wireless network.i've also noticed that the WCG200 is not listed on the Linksys Windows Vista Support page. does this mean that my WCG200 is not supported to work with Vista. if so, why are there Vista drivers available for download?currently i am connected via wire and it works fine. it also detects my wireless network. the problem is just connecting to it.

View 9 Replies View Related

Linksys Cable / DSL :: No Drivers Were Listed As Needed For Wcg200

Jun 19, 2012

I just replaced a hard drive on my computer, installed win7, hooked up the linksys according to the guide but it is not recognizing anything attached.  My devices indicates an unknown ethernet controller.  I have installed no drivers for anything, no drivers were listed as needed for wcg200. 
 
The same linksys is hooked up to a second computer (which I am posting from) so I am assuming it works fine.  Also I had the thing set up on the last harddrive with win7, the only difference was the harddrive was loaded up with the OS by the computer shop.  I have never done this before and wanted to try it out. I swapped ethernet cables to make sure nothing changed with the cables, but no luck. 

View 1 Replies View Related

Linksys Wireless Router :: WRT54G V1 Disconnect Power From Router For About 15 Seconds / Plug It Back In

Apr 27, 2013

I have a Linksys WRT54G2 v1 router which is having a daily problem of connectiing to the Internet on my home wireless LAN. My temporary solution is to disconnect the power from the router for about 15 seconds and plug it back in .... and all is well.... at least for another day or so.The real problem is that instead of properly connecting to IPv4 address 192.168.1.100 ..... it randomly connects to Autoconfiguration IPv4 address 169.254.29.54 When this problem occurs the SSID list shows both my 192 connection as well as a public network with no Internet connection?
 
I've used this router for several years without a problem until I recently bought a new  Canon wireless MG5320 printer which initially had problems connecting to my LAN. After a telco with tech support the printer works fine but now I am now experiencing the Autoconfig address problem.My LAN consist of the WRT54G router, a Motorola cable modem, a Lenovo laptop running Win7 64bit, a Hp desktop running Win7 64bit  and the Canon wireless printer. (all connected wirelessly)

View 2 Replies View Related

Correct Polarity Of Power Input Plug For Vigor110 Modem?

Mar 6, 2012

What is the correct polarity of the power input plug for vigor110 modem?I know it should be 9volts but which part of the plug should be positive? Original power supply gone missing and no indication on unit of plug setting.

View 5 Replies View Related

Cisco Switching/Routing :: 2960 When Trying To Plug IP Camera Device / It Doesn't Take Any Power

Nov 12, 2011

when am trying to plug a PC into the switch, it takes power as the switch is POE . but when trying to plug IP Camera Device it does not take any power. although i have cisco 2960 - 24 ports both PC and IP Camera getting power. while troublshooting by #show power inline , i get nothing as well.

View 6 Replies View Related

Cisco Switching/Routing :: 3750x - Plug In Powerstack Cables With Switch Power Applied?

Mar 13, 2013

I have a customer that has a stack of 3750x switches installed in production and now would like to install the powerstack cables. The switches are in production and downtime would like to be avoided. Can you install the powerstack cables with the switches powered up? I would assume you can, but wanted to verify before doing so.

View 4 Replies View Related

Linksys Cable / DSL :: X2000 Power Led Is Red

Jun 27, 2012

linksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work

View 3 Replies View Related

How To Plug In Ethernet And Phone Cord Cable

Jan 6, 2011

This modem has only three ports. How can I plug in an Ethernet cable and a phone cord cable?

View 1 Replies View Related

Plug Wireless Router To Cable Modem?

Feb 4, 2012

How do I plug the wireless router to the cable modem?

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N Red Power Light

Apr 4, 2012

My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !

View 3 Replies View Related

Linksys Cable / DSL :: Transmission Power On A WAG160N?

Apr 15, 2012

I am trying to lower the transmission power on my WAG160N. I thought it should be an option in my advanced wireless settings of the web based setup page, however there is only transmission rate, n transmission rate and cts protection mode.

View 1 Replies View Related

D-Link DIR-601 :: Must Unplug / Plug Back In Cable Modem

Jun 30, 2011

I've had my DIR-601 for almost a year now and it's been working near flawlessly until just recently.  I have a very simple setup with a desktop PC, router, Time Warner cable modem, and the only device that accesses the router is my Droid phone.  I shut my PC down every night.  The next day when starting up my PC, there's no internet connection.  I haven't fooled around with any router settings, but what I've been doing to re-connect is unplug the cable modem power cord and router power code, wait a minute, then re-plug them back in and it connects right away.  Is there something easy that I can do/repair to correct this?  Maybe I should check if there are firmware updates?

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Power Cycle Or Reboot

Aug 1, 2011

It seems there's no way to reboot this device from the browser interface.  You have to actually go and recycle the power by physically pressing the button.Plus, to setup Port Forwarding you have to reboot the modem.This is a major problem because it means you have to be on the premises to change things like the port forwarding.  You setup it up, but have to reboot for it to take effect.

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N USB Printer And Transmission Power?

Feb 12, 2011

1. Does Linksys WAG320N support USB printer? Can I connect a printer to USB-port and send some text to print from notebook via wi-fi?

2. The fact is that I have a cheap, simple chinese WiFi-ADSL-modem ZTE, which has 3 modes - low / medium / high for WI-FI signal. So, the signal is transmitted by ZTE at LOW-level is equivalent to signal, which now sends my WAG320N. When I  turn ZTE on high-level, then the range of wi-fi signal increases much, comparing with the range given by WAG320N. So, where can I turn on high-mode in my WAG320N?

View 1 Replies View Related

USB Wireless Card Doesn't Work Until Plug In An Ethernet Cable?

Jan 1, 2013

I have a Belkin usb adapter to pick up my wireless internet. problem is when i choose my network to connect to it constantly says "acquring network address". But as soon as i plug in an ethernet cable from the router the wireless starts working and i just unplug the ethernet cble. So why does my wireelss card depend on my ethernet conenction?

View 7 Replies View Related

Linksys Cable / DSL :: WAG 200G - Installing Power Socket Not Working?

Mar 8, 2012

I purchased wag 200g from dubai more than a year ago. When i tried installing the power socket never worked and till date I never got a solution for this. At present I do not have any documents relafinding a cisco authorised service center in India but in vainted to this product but this issue could not be solved by any computer service center.

View 1 Replies View Related

6867R - Network Cable Is Unplugged When Plug ADSL Line To Router?

Nov 20, 2011

I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Loosing Internal Settings After Power Reset?

Dec 19, 2010

I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?

View 5 Replies View Related

Linksys Cable / DSL :: WAG320N - Loosing Internal Settings After Power Reset

Aug 25, 2011

I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)
 
However ...when powering off (and back on) the device , my Dream box Satellite units (DM500) could not get access to the internet anymore (outbound) on port 12000.

All other internet traffic went fine ...through browser, wireless, ...all OK.....I tried everything to resolve but ultimately only succeeded in re-configuring from scratch. This solved the issue .....until ....right...I powered off the device and brought it back up ....same symptoms. Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all OK again .....until I powered the device off and back on .....

I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dream box unit directly to the device) and ....same symptoms ....when powering off/on, the dream box cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.

And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works OK ). It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ? (and ...no...I did not setup any port forwarding not triggering.

View 7 Replies View Related

Linksys Wireless Router :: E3000 Unplug Modem Power And Tv Cable

Nov 25, 2011

i have an e3000 linksys cisco router. i havent had any problems before until i tried adding a new computer via cat5e ethernet cable. The first computer always is connected fine whether i unplug the router or modem in any order and replug. i dont know much how to fix this. ive tried some unplugging method once but it only worked until i turned the computer off and back on later. i am also running 2 xboxs with no trouble. i used cisco connect to diagnose problem but it just told me to unplug modem power and tv cable and i did that with no luck.although i have good equipment, the internet is pretty slow.i have the best service of my provider that states it has upto 50 mpbs download speed.i ran the cisco internet speed test and only got a max of 20 download and 5 upload.how could i speed this up?

View 9 Replies View Related

Use Wcg200 As Bridge?

Dec 19, 2012

So I have an RV120W as my "main router" but I can't get a wire into the garage to get a couple of computers in there access to the internet / LAN. I have a WCG200 cable gateway at my disposal, with a built in 4port switch and wondered if I can configure it's WLAN to connecto the RV120W SSID and use wireless as my link between my garage network and the rest of the house LAN? WCG200 isn't going to connect at blinding speeds, which I'm ok with, I just wanted to know if it's possible?

View 3 Replies View Related

WCG200 - VPN Not Connecting From Outside Of Router?

Jul 11, 2011

I am new to VPN and have set a server up using windows XP's built in feature. I have tried to connect to the VPN from inside the router and it works fine. but I can't access from outside of the router. The computer will connect but then when on the "Verifying Username and Password" step the connection will disconnect with error 721: The remote computer did not respond. The router that i have is a Lynksys WCG200, I have tried turning all the security features off. Could my router just not be compatible with VPN?

View 9 Replies View Related

Linksys WRT54G When Plug Any PC Into Ethernet Ports It Doesn't Work

Feb 1, 2011

I have the Linksys WRT54G Wireless Router, when i hook my at&t modem to the modem port on the router the wireless portion of the router works, when i plug any pc into the Ethernet ports it doesnt work!If i plug the modem into the Ethernet port and plug other pcs into the other existing Ethernet ports it works by Ethernet but not wireless.

View 1 Replies View Related

LAN Through Power-line Or Coax Cable?

Mar 5, 2013

I have been trying for a week now to figure out how to wire the upstairs bedroom in my house, I live in michigan and don't want to go on the roof.Found these on Amazon and was wondering which would be most reliable as I have both a coax cable and power lines in my bedroom .

View 1 Replies View Related

No Internet Connection After Cable Power Went Out

Jun 14, 2011

We have optimum dsl, windows 7 computers, a windows server a lynksys router and a gigabit switch. The cable power went out in the area last friday. Now they say the internet is on but our network wont pick it up. After reading a number of sites it seems our switch to router may be the issue. the switch has all similar ports for network cable connections. the router has an obvious port for the main cable internet connection. I can not figure out if the location of connectors on the gigabyte switch matter in terms of where the switch and router connect to each other. this all worked last week. my other problem is that i have no internet access at the office to troubleshoot this. I dont remember model numbers for the switch and modem. we have 6 computers networked.

View 3 Replies View Related

Linksys Wireless Router :: EA3500 Disconnect After Plug In Portable Hard Drive

Mar 6, 2013

I bought an EA 3500 refurbished through linksys. I can't configurate it using the CD-Rom. Always said "can't find your router". So I flash with the classic firmware, and it fixs the problem and automatically upgrade to smart Wi-Fi. That being said, whenever I plug in a portable hard drive, the router disconnect from internet after a minute. I tried my seagate HDD and also my flash driver. Both Lost internet after a minute or so. So I think it is probably the router's problem.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved