I have been trying for a week now to figure out how to wire the upstairs bedroom in my house, I live in michigan and don't want to go on the roof.Found these on Amazon and was wondering which would be most reliable as I have both a coax cable and power lines in my bedroom .
View 1 Replieshow far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedUsing particular coax cable between a MGX and a Cisco 3845 router. The router has a NM-1A-T3/E3 network module (most likely since the label that the guys onsite saw at the back of the router says 1A-T3.The MGX meanwhile has a AXSME-16T3E3 front card and a SMB 8TE (?) back card, based on what our client said. There is presently a miniBNC-to-BNC coax cable connecting the MGX to the 3845, muck like the picture below. There are CRC errors on the ATM interface and the client would like to replace this cable. Unfortunately, I cannot find the exact Cisco cable for this.
View 3 Replies View RelatedI work for a place that has its own TV broadcast system. From the central site we have contracted fiber connectivity to each of our 10 remote locations. To each location we currently have fiber for data (1Gbps) and fiber to transport our TV channels. Am am looking for a device that can take in our TV channels on coax and give me an rj45 ethernet connection so I can plug the unit into a data switch to use our data fiber for everything (if I need 10 units at the central site to do this, that is fine).taking the ethernet back to coax to distribute TV to all of the TVs in the building. This would eliminate me 10 point to point fiber links.
View 6 Replies View RelatedI just got those TrendNet 500Mbps powerline adapters. Testing with CrystalDiskMark on a laptop to a remote SSD drive I get the following results. Notice that those are megabytes. [code]
View 2 Replies View RelatedI have two networks with two different external IP address, of course I have two routers where separate PCs are connected.
My question is if is possible to run with the adapter like DHP-342 or DHP 200 this two LANs over power without conflict?
Is it possible for Time Warner Cable to use a pre-existing cable line which is going into my cable box to hook up a modem so I can have Internet? I've got a modem in another room but I don't want a cable running down my hallway for 30 feet.
View 6 Replies View RelatedI currently have a pair of NETGEAR XAVB2001-100NAS Up to 200Mbps Powerline AV 200 Adapters. Can I just add a third unit upstairs (like url...) and all three ports will have connectivity to each other?
View 2 Replies View RelatedTwo of us were using power line adapters to connect to the router. We had no problems whatsoever. Then my other friend got a power line adapter and starte connecting that way too. Then pretty much both mine and his stopped working. Yet my other friend can still use his no problem.I ran and ipconfig /all and I'm noticing that its not giving me a default gateway address. I tried inputting it manually and still nothing. My windows 7 pc keeps saying it can't identify the network.I also have this problem when I try connecting my Xbox and he has the same issues with his ps3.Yet we can both connect wirelessly with no problems.The router in question is a Netgear N300+.
View 14 Replies View RelatedI have got a TP link wireless router connected by TP link power line ethernet adapters connected to my sky box, one to Samsung Smart TV, which both work fine the third I have connected to my computer. This shows up as as a local area connection but with no internet access. I have similar problems to other people with internet access dropping out after installing Windows * and had hoped an ethernet connection would be more stable. Any thoughts on why I can't connect to the internet via my powerline adapter.
View 5 Replies View RelatedI have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other.
The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!
The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date!
My situation is as follows: A modem in the hallway closet with an internet connection via a coax cable. A living room with an i Mac and a Philips PFL9604 TV connected to the wireless network. The wireless network is provided by a new TP- Link TL-WR1043ND router which is setup next to the modem.
I would like to do the following:
Stream content such as HD movies, shows etc from the i Mac to the TV. Use the TV to watch missed shows with the apps on the TV via internet. Make use of the internet speed upgrade (75 - 150 m bit/s) which will come in a few months. However the signal of the router currently isn't strong enough to maintain a stable connection since it's too far away. The distance from the router to the TV and the i Mac is 12 meters and 6 meters with a wall in between as well. Now I can't move the modem from the hallway closet else the signal to the modem will be too weak nor can I wire an utp cable from the hallway to the living room and put the router there.
I have come up with two possible options now:
Use power line adapters by plugging one into the hallway socket and one in the living room so I can put the router there.
I currently have these power line adapter to try out, however my internet connection occasionally drops while using these adapters. Take the old WRT54GL router or a second TP- Link TL-WR1043ND and use WDS to create 1 network and have good coverage in the living room. The i Mac and TV can then be connected via Ethernet cables to the second router if necessary. I assume it would be best to place the second router closest to the first one for the strongest signal.
The second options seems the best to me as the power line adapters don't seem very promising based on my experience so far. I would like to know if connecting two routers is a viable method to obtain good and stable coverage in the living room?
We have a few touch lamps (touch the base to turn on) that comes on all by themselves after I setup the PLK300 kit. Is this a natural occurrence with a powerline networking kit? Of is there a firmware update that solves this problem?
View 3 Replies View RelatedI have Comcast broadband with one modem connected to my PC. I just bought a Denon AVR-991 Receiver that has internet capability. I I plan to use it for internet radio, etc.The problem is that each piece of equipment is in different areas of the house. I could connect the cable modem to the receiver and connect the PC to the internet via a wireless router, but I don't want to lose the speed of a direct connection on the PC.. can I have two different modems connected to the same incoming cable line? FYI, the existing modem is a Linksys BEFCMU10, and the second modem is one Comcast is in the process of sending to me as I just added Voip phone service to my account.
View 2 Replies View RelatedI just bought a new wireless modem router Linksys X2000 And I couldn't find the line status like SN margin and line attenuation and so on [URL]
how to access my ADSL line status
I have ADSL router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->
[Code]....
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedI am looking for a router or something else that still allows me to connect my phone line to my router or computer so people in the house can make calls. My cable modem is a Motorola SBV5120 I had it for eight years now and I am thinking of switching our network to wireless so I don't get those cluttered wires.
View 1 Replies View RelatedOn my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
View 1 Replies View RelatedHere's the problem : I've installed this router to a friends of mine home and since then in the gam "Warhammer 40000 Dawn of War 2 : Retribution" they can't play together (they're connected via WAN) in a 2v2 without getting disconnected FROM THE INTERNET (not only the game, the whole ADSL line collapse after an over 3000ms of ping for few sec.). Same thing if one of them try to make a 3v3 (so 1 with the WAG160Nv2, and 2 other persons via internet.), 3000pings for few sec and then they get DC from the internet, after few sec the router gets back online but still they can't play together or make a 3v3.
View 1 Replies View RelatedI can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies View RelatedI have two buildings. In first building I have network with internet. In other building network without internet. I need to connect buildings to the same network using two WAG320N modems by the phone line cable. Is it possible and what configuration I need to set up?
View 2 Replies View RelatedI have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies View RelatedWe have optimum dsl, windows 7 computers, a windows server a lynksys router and a gigabit switch. The cable power went out in the area last friday. Now they say the internet is on but our network wont pick it up. After reading a number of sites it seems our switch to router may be the issue. the switch has all similar ports for network cable connections. the router has an obvious port for the main cable internet connection. I can not figure out if the location of connectors on the gigabyte switch matter in terms of where the switch and router connect to each other. this all worked last week. my other problem is that i have no internet access at the office to troubleshoot this. I dont remember model numbers for the switch and modem. we have 6 computers networked.
View 3 Replies View Relatedlinksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work
View 3 Replies View RelatedSo I got a new router (DIR 655), but I forgot Verizon FIOS is using coaxial cable in my house. I looked around and seems like I can just call them to have it switched to ethernet connection. Would that cost extra? Or can I just do it myself? I don't have FIOS TV btw.
View 12 Replies View RelatedMy WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View RelatedI have a WCG200 v1, and lately it keeps reseting, so I started thinking maybe it's a power problem. I go to unplug it, and the power plug is extremely hot, so we unplug it, and let it cool off, then plug it back in later. It works fine, and we go to bed, I wake up this morning and it's back to very hot again..
View 2 Replies View RelatedI am trying to lower the transmission power on my WAG160N. I thought it should be an option in my advanced wireless settings of the web based setup page, however there is only transmission rate, n transmission rate and cts protection mode.
View 1 Replies View Relatedi'm trying to connect my xbox360 to the internet. I'm upstairs, my modem and router are downstairs. I'd prefer not to have to get a wireless adaptor for my xbox, but if that's the only way, i'll settle with that.We have Comporium internet. I can get cable if I hook a cable box up to the coax port in the wall upstairs. I have been looking at coax to ethernet adaptors, hoping I could go from the coax in the wall, to the adaptor, right into the back of the xbox. Is this possible?
View 1 Replies View RelatedI moved from an apartment where they had run ethernet to a jack for me to plug it into my own router, it was nice. My new apartment the installer came over when i wasn't there (my gf was there) and he installed a coax jack next to my router and supplied a huge frontier box (wireless router/modem). And then connected it to my router.
After much configuration I finally got it to run good on my router, and I started wondering if I'm going to get the same latency and speeds as it was on ethernet straight from the box. I'm paying for a 30/10 connection. I'm sure the coax is enough, but it's the cheap Frontier box and coax connection together that I wonder about.
My ultimate question is, I have an old motorola DOCSIS 3.0 Surfboard modem (when I had Comcast) that I have laying around, will it work with it? I assume it will be better. I really dont need all the junk that this huge Frontier box has. I just want a good connection.BTW my router is a DIR-655.
It seems there's no way to reboot this device from the browser interface. You have to actually go and recycle the power by physically pressing the button.Plus, to setup Port Forwarding you have to reboot the modem.This is a major problem because it means you have to be on the premises to change things like the port forwarding. You setup it up, but have to reboot for it to take effect.
View 1 Replies View Related1. Does Linksys WAG320N support USB printer? Can I connect a printer to USB-port and send some text to print from notebook via wi-fi?
2. The fact is that I have a cheap, simple chinese WiFi-ADSL-modem ZTE, which has 3 modes - low / medium / high for WI-FI signal. So, the signal is transmitted by ZTE at LOW-level is equivalent to signal, which now sends my WAG320N. When I turn ZTE on high-level, then the range of wi-fi signal increases much, comparing with the range given by WAG320N. So, where can I turn on high-mode in my WAG320N?