TP-Link 300Mbps Wireless :: WR841ND / WR541G - Configuring 2 Routers To One Cable Modem
Mar 29, 2013
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
Region : Germany Model : TL-WR841ND Hardware Version : V8 Firmware Version : 8.1 ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany Model : TL-WR841ND Hardware Version : V3 Firmware Version : 3.13.18 ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
Region : Italy Model : TL-WR841ND Hardware Version : V8 Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
Region : UnitedStates Model : TL-WR841ND Hardware Version : V5 Firmware Version : ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
Region : Malaysia Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.12.9 Build 120221 Rel.31475n ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
Region : Portugal Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Others Model : TL-WR841ND Hardware Version : V8 Firmware Version : wr841nv8_en_3_13_27_up_boot(121101) ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master) Connects to the internet/ADSL DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
Region : Brazil Model : TL-WR841ND Hardware Version : V7 Firmware Version : 3.13.9 (Last) ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Romania Model : TL-WR841ND Hardware Version : Firmware Version : 3.13.27 Build 121101 Rel.38183n ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Recently I had changed my ISP and I get a brand new modem and a D-Link DIR-615 wireless router, but the problem is the wireless signal is not strong enough to reach second floor, so I decided to get a new TP-Link TL-WA901ND access point and after configure the AP to repeaters mode, I saw it has traffic coming throughout to the AP but my PC cannot get any internet connection not even an IP address. When I was facing this problem, I thinking of is that possible using my old wireless router which is TP-Link TL-WR841ND to have a internet connection working with D-Link wireless router, I had tried plug my TP-Link router LAN port to D-Link router LAN port with a network cable and setting into same IP range (192.169.0.xx) but cannot get any traffic getting through.
I'm trying to configure mine as a wireless repeater, but to no avail. Here's what I've done so far: disabled WPS changed my router's IP to 192.168.0.2 (because the source router's IP is 192.168.0.1) rebooted the router enabled WDS, found the network I want to repeat using the Survey feature, then filled in the WPA2 password. enabled WPA2 security on my own repeated network, using the same authentication type and password as the original rebooted the router.
My router complains that "WAN port is unplugged", and it doesn't get a WAN IP or incoming packets, which probably means it's expecting the internet signal to come from the WAN port rather than the wireless network I set up, right? How can I force the router to connect to the network? Also, should both routers be in the same subnet? I've tried with different subnets but nothing changes. The source router is a D-Link DIR-600.
Region : India Model : TL-WR841N Hardware Version : V8 Firmware Version : ISP : Reliance
I got a new broad band connection , its with an ADSL modem (ZTE ZXDSL 831). Now i want to plug in my TL-WR841N to use my WiFi and to connect to my second machine!! no matter what setup i try, i'm unable to connect
Region : UnitedKingdom Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version : ISP : Virgin Media
Bought recently and I'm very pleased with Setup and Performance.
However, even though I have tried repeatedly with different user details and passwords I cant access the router Config without resetting to defaults using the pin in the back and admin admin.
I am using W7 and get to a log in screen via Control Panel / ... Network Sharing Centre / Network Map and see Router. Click on this and up comes a User Name and Pasword form but it never works with what I entered for the router.
Region : France Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.13 build 120405 ISP :
i discovered a speed issue with cable with my router TL-WR1043ND. i have no more than 11 MB/s from computer to NAS... so like all transfer speed was setup like a 100Mbps adapter. my card on my computer is in auto negotiation. If i set it manually to 1Gbps no link is active between router and computer. i tried it with my laptop and once again the same issue.
I have managed to get the wireless portion of my router working for the two wireless laptops in my house (one is Win XP, the other Linux) and am now trying to connect via rj45 ports + ethernet cat5e cable, my router and desktop computer that is running Windows XP. My connection type, set when I setup my wireless router, is pppoe.I have my router connected to a SpeedStream Modem, my ISP is Bell.I am worried that I will have to purchase a hub/switch in order to allow the desktop (PC3) to access the internet, although it seems to me (from reading other internet postings) that what I am attempting to do should work with just the modem+router setup that I have.I haven't worked with Windows LAN networks before (wired, not wireless) I have only dealt with my laptop's wireless internet connections and it seems much simpler to deal with than wired lan connections.
configuring 2620 cisco to cable modem for internet.I'm setting up a lab to practice and am having trouble getting this to work.Made several configs that don't work and starting over form scratch.
Region : Canada Model : TL-WR1043ND Hardware Version : V1
I was wondering if it is possible to connect two routers through wireless and make them talk to each other. Here is why I need it, I currently Have 6 wireless IP Cameras going too 8. 2 are wired on one router in my house and the other 4 are wireless(with wired capabilities) Im going to wire the other 4 too a 2nd router so the cameras are always running and don't suffer any down time due to signal loss (happening a lot at the moment). How can I get Router B to talk to Router A, so I can look at all of the cameras from Laptop in my house which is closer to Router A.
My Router A is TL-WR1043ND, I'm also going to probably buy another one. How to configure it properly. So I can login to the cameras from my laptop.
My setup consists of the following: TP-LINK Router Model No. TL-WR541G and TP-LINK Wireless Repeater Model No. TL-WA500G.I've set the Wireless Mode Settings to Universal Repeater and turned on MAC filtering. My problem is that when I connect to the wireless repeater with a phone or tablet (both working on android) it just wont connect. It gets stuck on "obtaining ip address". The wireless repeater works fine with any laptop, pc, netbook etc. I made sure that all the MAC Addresses are entered correctly. Also the phone and tablet connect fine to the router, but when the router is out of range and it tries to connect to the repeater it doesnt work. I tried all the basic troubleshooting techniques i.e. turning off wifi, turning off repeater & router.
I have a TP-Link WR541G/542G router which I would like to utilize as a switch to connect my xbox 360, blue ray player and TV box to the internet. The switch is connected to a powerline adapter and another adapter is connected to the main router Huawei HG533. I have tried to follow your instructions I found in the thread however it did not work.
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
I have linksys router connected to my cable modem. I want to change it Belkin AC900. How can I keep the linksys connected until I have tested set up for Belkin AC900 router.
We have kids in the house and I'd like to limit their internet access to certain times of the day but because of the great amount of devices they use (phones, tablets, laptops, etc.) the only way I could think of doing that easily was to set up two wireless networks: one that the adults could use 24/7 and the other that the kids could access during certain set hours.
Here's the equipment I'm working with:
DLink DIR 615 wireless router DLink DIR 515 wireless router Motorola Surfboard cable modem S85101U
I plugged the DLink 615 in, set it up for DHCP client and plugged it into the cable modem. I lef the default 192.168.0.1 IP address for the device. On that router, I also reserved the 192.168.0.199 IP address and assigned it to the DLink 515.I also gave the DLink 515 device the IP 192.168.1.1 so I could administer it.I set the DLink 515 to static IP and made the IP 192.168.0.199 and the default gateway 192.168.0.1.I plugged the DLink 515 into one of the LAN ports in the DLink 615.I set a schedule on the DLink 615 to shut down internet access to the DLink 515 at a certain hour and turn it back on at another time.Everything seems to work ok, but at least once a day we have to unplug and plug the routers to reset them.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : charter, its smarter.
so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.
My computer is not wireless so I have needed a wireless router from Time Warner. Directions tell me to connect to my computer. Will that solve the fact that my computer is not built in wireless?
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
