Region : United Kingdom
Model : TL-WR841ND
Hardware Version : Not Clear
Firmware Version : 7.1
ISP :
failed to verify router settings
What's wrong with my router?
Region : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
I've been trying to set up my TP-Link WR740N router but it always give the error "Failed to Verify router settings" on the last step of the set up screen. Broadband: Globe broadband (Wired)Modem: Siemen Gigaset SE260 I'm also confused on the 2nd Set up screen, it gives the option to select Dynamic IP Static IP PPoEI've tried using the Dynamic IP and PPoE but still getting the same error message
View 1 Replies View RelatedRegion : Brazil
Model : TL-WR841ND
Hardware Version : V7
Firmware Version : 3.13.9 (Last)
ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany
Model : TL-WR841ND
Hardware Version : V3
Firmware Version : 3.13.18
ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
Region : Italy
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V5
Firmware Version :
ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
Region : Malaysia
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.12.9 Build 120221 Rel.31475n
ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
Region : Portugal
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Others
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : wr841nv8_en_3_13_27_up_boot(121101)
ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master)
Connects to the internet/ADSL
DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
What can couse this very slow transfer speed?
Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
Region : UnitedKingdom
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3-14-4 to 3-15-4
ISP : Primus Saver
I had it all working fine, then I wanted to upgrade the firmware. The original firmware was 3-14-4. I downloaded and applied the 3-15-4 firmware. Now when it powers on the power light is on all the time. Immediately the sys, 4, 3, 2, 1, Internet, usb and wps lights flash once. Then about 5 seconds later the 4, 3, 2, 1 & Internet lights flash once, then a second later the cycle starts again. When I connect it to the PC it starts to make a connection on the NIC, but then the router resets. Model: TL-WR1042ND, Ver 1.3 . Is there a way to reset the firmware or get it working again?
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have two(2) WR941ND routers working at my home. The primary has IP : 192.168.1.2 , this primary router is working as an Acess Point, DHCP is OFF, and no wireless security activated. This primary router is connected to a DSL modem+router and DHCP is activated on it.For the secondary router I configred 192.168.1.100 . On the secondary router I have activated WDS function as well as Wireless Security (WPA2) , DHCP is Off on it. This secondary router is to work as wireless bridge + Access Point. You will understand that this secondary router is wirelessly connected to the primary one.I am able to configure all, and all things work correctly for few days at a time.But if at any time the secondary router is switched OFF, and then again switched ON, it seems to have lost al the settings and its IPs, and thus unable to connect to primary router. At such time I am unable to locate /connect my laptop to this secondary router, and it keeps on searching & searching.
Region : Others
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
View 1 Replies View RelatedHow to verify router's wireless set up is secured ( and encrypted) from Admin GUI ?Which menu to look at in Admin GUI ?
View 3 Replies View RelatedGetting this error on the data center 2581 (12.4(24)T) from a GRE/IPSEC tunnel, remote branch is 2811 running 12.4(25d)
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed for connection id=
The tunnel has been up and working okay for months, nothing has changed on the config and the key is correct. Traffic is following but remote users are complaining of performance issues. A wireshark shows checksum errors and lots of packet resends. Remote ISP has checked the circuit and says its clean.The data centre router has quite a few tunnels but only 1 causing this issue. From the head end router -
sh crypto ips sa | b x.x.x.x
current_peer x.x.x.xport 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 15129, #pkts encrypt: 15129, #pkts digest: 15129 #pkts decaps: 13346, #pkts decrypt: 13346, #pkts verify: 13346 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0 #pkts not decompressed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 1992
Can a VPN module go bad like this? I've tried disabling the branch onboard engine and using software but it doesn't work.
I upgraded the firmware per one suggestion, but no difference.I am going thru the setup wizard with ethernet cable attached. I want to use them wirelessly so I clicked wireless setup, and entered my network info. At that point I get an error message saying it failed to save settings. I know the ID and password are correct.I have tried exiting the setup wizard and accessing the camera thru the web interface. All wireless settings are correct. The camera works FINE on web browser, myDlink, and even my iPhone app as long as the ethernet cable is attached.Other wireless devices have no trouble connecting to my router. Is there some setting on the router that can be preventing the connection? I've done some trial-and-error changes, like different ports and enabling/disabling UpNp on both camera and router.Oh and almost forgot to mention.I did call tech support, which was a joke. Some foreign lady was reading off a script that told me to reset, unplug, reboot everything. Then she gave me a case# and said upgrade the firmware.
View 11 Replies View RelatedRegion : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP : Bezeq benleumi
I want to setup WDS using my TL-wr941nd WDS router?
Region : Malaysia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 Build 120605 Rel.38634n
The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.
Region : Sweden
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :
Have just bought this new router and it works faultlessly on all laptops and mobile phones in the house except for a laptop running Vista, the TCP IP properties look all right, it asks for a username and password ( only if connected by an ethernet cable, otherwise it cant access a network) but they are not accepted, the same username password was accepted for al the other computers
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP :
I have a flaky internet connection, and it drops every few days. I've thus far powercycled my router by unplugging and plugging it back in, which fixes the issue.
I'm traveling soon, and would like to be able to have access to my stuff remotely, even after the connection drops.
I have two ideas:Run a script in Windows 7 which would soft reboot the modem - free, not sure if soft reboot is enough though. If that doesn't work, Get a hardware which would powercycle the router - haven't researched if these are readily available and cheap
Is there a way to schedule a soft reboot of my router using Windows system tools? I'd schedule it to reboot every night.
Region : Others
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Baltcom TV
I have very low speed with router.First test without router - using cable directly to PC (DLINK DGS-3210 Managed SW - > My PC), here is result : Second test, using WR1043ND router (DLINK DGS-3210 Managed SW - > WR1043ND Router -> My PC), here is result : First of all, i thought that maybe WAN port is 100Mbit mode, but after i checked it on SW - port is still in 1Gig Mode (from router to PC, it is also 1Gig)Also downloading speed have same picture...Without router i get around 55MB/s, with router max that i saw is ~14MB/s....
Region : Canada
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 1
ISP : Kwic Internet
I have up graded to Windows 8 PRO but when I try to setup a wireless network Windows cannot find my router.
Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Which WORKGROUP does router have for sharing? I need this, because I have WD TW live and want to access routers usb hdd through sharing. Because router media server only supports up to 100 files, I see no other solution.Is there anyway to set the workgroup
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12
My router is not working wireless. Just stopped working. I hadn't touched anything in the settings. Nothing is picking up it's signal. All the lights are on saying that it SHOULD be working!I checked all the settings and they were as before. I have unplugged it and restarted, I have reset to factory settings and set it back up again but nothing! Works fine on the wire.
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version :
ISP : blueyonder
I am having a problem connecting my router to my cable modem. I keep getting the check network status.
Region : UnitedStates
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version : 3.12.5 Build 100929
ISP :
I have the WR841N v6/v7 Firmware 3.12.5 Build 100929
The router stops showing up after 30 minutes to 1 hour. If I switch it off and on , it starts working normally but again suddenly stops and cannot be detected after 30 mts- 1 hour.